Secware_Tech6

as118150 Whats the day mode current of this panel? ALso the charging voltage would be useful. As a side note, what detectors on on this panel? ANd what battery is in it / age?

Tynesider. Sorry I missed your thread yesterday. Nice detailed post AM i right in thinking from the post you have a problem with a simple set reader? If so, i would remove it from where it is fitted, disconnect all keypad wiring at the panel and just wire the one simple set in. If it works then we have eliminated a hardware fault. IF not it looks like we have a faulty simplset. 25m is fine. James

Are the other keys working correctly? If so id assume its a keypad problem. Assuming the warranty has expired id open it up and check the carbon pads etc from the back of the keypad. It might only need a clean. Where was it stored? somewhere damp?

Looking at the above images you have it wired correctly. I can only suggest the panel is faulty. If you raise an RMA ticket we will get that panel swapped for you.

These images were sent in.

Im a bit of a galaxy fan so i would say the galaxy. eg. galaxy 2 or dimension eg http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=193 or http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=2064 if using the dimension that will take touchscreens (1 per line so 1 on the Dimension 48 up to 4 on the 520) the G2 wont take a touchscreen Both panels will accept additional MK7 keypads / keyprox's http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=699 Quad pir wise you have quite a choice. It does depend on your environment, use etc. Not all quad sensors are created equal. Dualtec wise for an outhouse id recommend a DT74 series ie http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=1676 Internal door contacts to suit the door. again depends on application Garage door. You can use a std door contact but id recommend using a roller shutter type. Panic button, do you want single push double push etc? Whole seperate topic here IMHO Txt / speech dialler Both the galaxy units above have built in modems for sms via a landline. They also have built in digital comm units so can be set to signal an arc as std. Listen in function. To do this properly you would need the audi confirm module on the dimension and microphones in the relevant areas. SOme diallers have a very basic version of this functionallity ie the pyronix speech dialler and the better menvier units. Dial in arm etc. You cant do this on the galaxy without the pc software. If you want to dial in, then only the rf panels offer this, ie visonic powermax and the risco wisdom. There is a web client though for the scantronic ION40 unit. wired/wireless the dimension and the g2 will accept rf expanders making them into hybrid panel. The GD-48 is a fine high end panel. it may be overkil but that depends on your requirments. I have a dimension at home myself.

Chris The power requirments of the keypad itself are very low. The main value to consider is the current required by the lock. 0.5mm flex would be fine for this purpose, however is the run is short then std alarm cable is normally used. YOu may need to parralel up cores if the volt drop is too large.

you will need to use the keypad unless you have the rss software to enable programming vis rs232

Is this something you installed / look after?

What keypad is it?

when you say intermittantly is it possible a range or interference issue?

I dont know of a professional grade door alarm unit sorry.

i dont think you can omit the entry zone on a 9448. If you just wanted that zone on then yes you would have to omit all the other circuits. You may be better of with a more powerful panel that allows multiple part sets

15v is too high but id assume that is your meter. If your panel is outputing 12 v- 14v normally id say there was a fault with the panel. Dont suppose you can attach a pic of how both sides are wired so i can double check them?

You could reprogram the part set, but this panel only has a full set and 1 part set option you can add additional sensors assuming the panel has spare capacity. it will also accept additional keypads.

Id say probably not as unless your planning on taking the fresnel lens out and putting something else in its place that the cam can look through. Are they pinhole board cameras? Also re the regs etc, you do have a duty of care to make him aware of them etc. Just be very careful with coverts in a public place.

There are plenty of covert cams available in pir's smoke detectors, junction boxes etc. But i dont know of any manufacturer that releases pir cases only. The best thing to hide them in, are things that are already there. Just a word of warning if its commercial and it sounds like it is, be very careful how you impliment this, there are regs etc you need to comply with.

I have attached a wiring diagram

the grey fobs will work on the galaxy keyprox but not on a galaxy max reader, the black fobs work on both readers.

It is technical possible but it requires a modification. (there is a programmable output on the mk7 but you cant wire to it) Best thing to do is either go from the panel itself or a RIO

Its not one of seen on a cpx but that usually means the pane has restarted due to corruption or a hardware issue.

Thanks Phil However i dont see a question in your support request? James

When your disconnecting the strobe are you doing it at the panel or the sounder end? Id meter between Bell + and Strobe - at the panel with the strobe - disconnected. Whats the reading?

Elaibe can you ask risco about the recorded one?

The domonial rf kit is currently IMHO the best out there for range etc. However this will only function with the G2 galaxy range via an RF portal. On the dimension you can use a radio rio, but IMHO i would avoid the old radio rio and either use a standalone reciever and pir or use a G2. if using standalone you could use a http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&manufacturers_id=68&products_id=2126 then you could use a visonic wireless pir with that. there is also an 8 channel version.