Secware_Tech6

However note you are limited to 12 circuits / devices in total on the 12.

Any dusk sensor can be inverted with the use of a relay. If the devices are 240v then use a 240v coil relay, if 12v use a 12v one.

Technically the id and id plus systems are interoperable. However in practice this is not always the case. The voltages used by the 2 biscuit variants is slightly different. Many companies that used to use iD have a large stockpile of the old biscuit type to support legacy systems due to this issue.

iD whilst owned by honeywell, they dont actually make a control panel to support them. Texecom, Castle care tech and menvier currently do, however its a dying tech, texecom recently announced they would be pulling support for iD

Is this for access control or asset protection? Im afraid i dont fully understand the question.

If it was operational before then you have either damaged something on the connections or board or not seated the control panel tamper switch correctly.

It depends on your DVR outputs. What is the manufacturer of that model?

There are 2 issues here. Systems such as this are not normally used for recognition capture. If you want to capture regs then lens size or scene width are the most important aspect. You want to be viewing approx a scene width of approx 6m at the point of reg capture. You also need to be facing the reg in question with the camera. Too much offset angle will make it harder.

Usually the old obs kits just sent video over the cores not a twisted pair converted signal. Its not supported but you should be able to open a cable and test for power and video. However bear in mind some kits were actually line fed. I would suggest it be a better idea to replace the cameras with some not locked to that monitor

No it is double pole only.

Any NC door contact would be suitable ie ie http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&cPath=36_44&products_id=667 but it may depend on your door. What are your protecting?

You need to narrow down which tamper is the issue. ID loop out the global tamper, keypad tamer (if a gen4) and SAB tamper. If you can upload a photo of your board i can see which tampers are in use.

Im afraid we dont support zoneminder. I do watch the project however. I have not tested the cards we have with zm as for my own use I only use IP cameras. James

You need to connect the C and NC to the circuit on the panel.

If you dont wire it this way or use a dedicated line. Anyone picking up the phone will prevent the system dialling out. Sales will update the other point

Dependent upon steam build up etc id normally go for a weatherproof unit. ie http://www.securitywarehouse.co.uk/catalog/optex-lx402-p-86.html

Overkill IMO unless you need the range of a redwall. Have a look at the voltek pir and switcher units.

Adding or replacing user fobs is a manager function. Is the local led on the unit working, ie is the battery installed correctly. WHat process are you using to add the fob?

If you click on the above picture you will see a set of terminals for 'line' and 'set' The line connection pair is the tel line connector. You can plug it in but this isnt the best connection method. If you connect the line connections to 2 and 5 respectivly in your master socket plate

Are you looking at a particular unit? Most accept upto 4 telephone numbers but are generally regarded as a low security device (just like any voice / text dialler)

There is no power in a contact. YOu should be able to see the reed itself. That is your alarm pair. And the tamper pair go to the leaf spring

That is a basic logging function. Any of the higher end panels will do this. IF you dont currently have the software id look at the texecom premier range. Their software is called wintex and can be used to connect via a compatible modem. You can the download your events and print etc

No the premier keypads are for the premier panels. The excel is a different panel

The smaller panel can only handle 1 partition, but i wonder if your mixing up part set and partition. If you need more than 1 partition you need the more powerful panel. A partition in this case is to create a separate logical system that is full set etc independently. Normally only used on commercial systems Yes there is a reader in the panel It can do voice dialling but will require gsm and an active sim etc for texting