Jump to content
Security Warehouse Support Forum

Secware_Tech6

Administrators
 View Profile  See their activity

  • Posts

    256

  • Joined

  • Last visited

  • Days Won

    14

 Content Type 

Everything posted by Secware_Tech6

  1. Secware_Tech6
    Have you adjusted the range down, set for harsh on Pir and mic? What pet mode is it in? And can the cats get within 6 Ft of the detector?
  2. Secware_Tech6
    i dont think so, im sure you need the servers etc. The siemens panel can be connected to directly via up or using the spc ddns service
  3. Secware_Tech6
    I don't know what you mean by a call sender? Bellbox use a cqr multibox best sounder currently imo
  4. Secware_Tech6
    Have you followed the rf enroll procedure fully?
  5. Secware_Tech6
    If it's on it's pwn circuit then use the non latching base.
  6. Secware_Tech6
    I'd recommend the siemens eline Pir range and knight door contacts
  7. Secware_Tech6
    The 9930 is a keypad not a control panel. You need to know what radio Rx system you have.
  8. Secware_Tech6
    A master blaster would work in this situation but I'd advise getting someone to do it. Our equipment is professional gear and not designed for diy use
  9. Secware_Tech6
    As above if you don't need cams integrated into the same app then the dimension is a good panel
  10. Secware_Tech6
    No you can't on a basic system like this, you would need a more flexible siemens spc or Honeywell dimension
  11. Secware_Tech6
    If authorised pro installer then the hkc has the best app support.
  12. Secware_Tech6
    Yes they will you can adjust the beam interrupt time. What do you mean by phone card dialler?
  13. Secware_Tech6
    The only control panel that I know that can easily do that is the siemens spc range.
  14. Secware_Tech6
    Iirc the 6 wire keypad is no longer available. I would advise a replacement as id guess yours is well over 10 years old.
  15. Secware_Tech6
    No it has to show. What if it was a rear door and had been left open. Its only reporting it is activating it does not affect the exit procedure
  16. Secware_Tech6
    Non of our equipment is designed for diy installation. For that you need to use b&q etc as these supply the low security easy fit products
  17. Secware_Tech6
    Use an enersys 2.8 but it does depend on the system load. What is your standby current on the system?
  18. Secware_Tech6
    You need a panel that supports groups such as the galaxy dimension or siemens spc. Id recommend a cqr sounder and siemens pirs
  19. Secware_Tech6
    Ok yes the aerial will help bit you may need some more receivers
  20. Secware_Tech6
    Are you just using the internal aerials? What's the distances and environment
  21. Secware_Tech6
    The detector manual will show how. You need to remove the eol jumpers
  22. Secware_Tech6
    It looks like you have wired it double pole but configured your detector for eol use. Change the jumpers for non eol use and you should be ok
  23. Secware_Tech6
    No you cant you will need a 12v detector. Honeywell do a 12v non latching base for their detectors
  24. Secware_Tech6
    Could you upload a picture of the wiring, the dip switch/jumpers and what panel you are using please
  25. Secware_Tech6
    It does sound like the pirs have no power. On a pir if there is no power they will be in alarm. Do the walk test less illuminate on the pirs
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept