Intruder Alarms

I need to change the battery on my alarm will the Enersys 12v 2.3 A/h Battery be a suitable replacement?

Good afternoon, I purchased a Veritas system with lcd keypad. The issue I have is that the keypad is showing a tamper fault and the tamper switch does not seem to be working. I have check all of the system and everything else seems in order. Is there an reason this would be a fault ? Kindest regards

Hi, My G2-20 is set to EOL and all the other sensors I have purchased from you have had EOL built-in. I guess the Activ8 BG I purchased does not. Can you confirm how I should wire this to my Honeywell Galaxy G2 panel. I have two zones spare that I'd like to use for the motion and the break glass feature of the Activ8. I guess I need to wire a 1k resistor between two of the terminals but not sure which ones. Terminal 1 & 2 - Tamper T 3 & 4 - R-PIR (normally closed) T 5 - EOL T 6 & 7 - R-MIC (normally closed) T 8 - +12v T 9 - GND Many thanks.

Hi, I already have a Galaxy G2-44 with : 2 Keyprox - MK7 & MK8 1 RF Portal - C079-2 1 Internal siren 5 wireless motion sensors - Honeywell DTPI8M 4 wireless door contacts - Honeywell DO8M 6 wireless Smoke Sensors - Honeywell DF8M 2 Wireless CO sensors - Honeywell CO8M I want to add a Honeywell ECO1005-A to this system as there is not a wireless heat-rising sensor for this system that I can find. First, it's wired so will it work OK with the wireless sensors or will there be any conflicts? Also, do I need a latching or non-latching base for this? Hope you can help and thanks,

Hello I am interested in the PowerMaster Visonic 33 Kit and I live in France, the system and accessories work in France? the instructions for use will be in French or only in English? Thank you

I am interested in buying a Premier Elite 48 panel from you and see that it comes with 8 Zones as standard. I understand that there are expansion slots in the panel to add more zones each slot in card gives an additional 8 zones. My installation will require around 28 Zones in total, so my questions are: How many expansion slots are there in the Elite 48 Panel before having to go to an external Expansion Module? Does Texecom produce a 16 Zone internal card or only 8 Zone? If I have to use an external module, is this powered from the main panel or will I require an addition Power Supply? What configuration will I need to have 32 Zones in total which will give me some …

I bought from yourselves about 2 years ago an Optima Compact Gen 4. following a burglary my insurance co are now insisting my alarm meets the above standards. Does this panel meet the above standard's, if not can you suggest one that does.

I am looking to upgrade my scantronics 9800 alarm system to remote control arm and disarm. I want to keep my exiting pir's and door contact and outside siren/ strobe box. Also I would like to keep the option of the keypad as well. I was looking at the LGSIX/01 unit. Will this unit do what I want. Also do you do any other remote control units that will work with this unit.

Hello I need to replace an wireless siren MCS-710 with a new model MCS-730/740. The control panel is a PowerMax Plus SN:15408.9BA2 JS700611 V3.4.08. Can you confirm that the MCS-730 and or MCS-740 are compatibile?

I need cable and software to program Galaxy 2 over PC, Please let me know what kind items do I need.

Hi, I am installing a Honeywell G2-20 alarm system at my home. I currently have two iWise 800QG3 movement sensors and am looking at installing an additional four to the system. I am considering purchasing the following detectors. https://www.securitywarehouse.co.uk/catalog/bosch-blue-line-gen-2-bld2-pet-tritech-blueline-detector-p-2392.html I understand TriTech is the best class of motion sensor to reduce false alarms. Is this sensor recommended or would you recommend something else? Any advice is much appreciated. Kind regards,

My wireless home alarm system has been jammed by source unknown. I have reset it but would like to back it up with hard wired system, not susceptible to jamming, for the upper floor of my house. Could you suggest components for such a system. I would like it to include Two PIRs (no need for pet friendly type) A remote wired keypad which can be set/unset easily without keying in a four number code ( I would like to either press one button or use a proximity tag, unless its operation can be jammed) A panic button (unless its operation can be jammed) Outside bellbox with battery back-up (not Odyssey) Thanks

Hi, looking to but the Texecom Kit 2 32 Zone Wireless Kit with Sounder but have some questions. How is the Premier LCDP powered... batteries of PSU? I assume the LCDP is wireless to the main control box? I have a couple of locations I would like to 'hard wire' will any 'standard' PIR be suitable for this? Is it only 4 hard wired channels I can use? Think I need a cover for the bell box with this kit? please point in right direction for this please

Hello, I have a scantronic 500r.+ system installed in 2002 which has been regularly serviced and works as installed. I now have a low battery light for one of the PIRs but the installer & servicer seems to have gone out of business as his phone contact is no longer recognised. Please could you say how to change the battery on the PIR as I do not know whether it has a tamper proof feature or not, hence, if I interfere with the PIR will it set off the alarm? Thanks for your help, Roger

i intend fitting a texacom premier and the client is wanting us to use the flush type keypads . can you advise as to the back boxes we need for these as we need them for the first fix stage . at the moment that will be two into brick and one optionally into plasterboard . can we order these upfront or do they only come with the keypads when ordered ?

Just bought an apartment with the above alarm fitted. At present no one seems to able to give us the access codes rendering the unit useless to us. Is there anyone who can reset it for us and/or give some helpful advice on its use. Thanks, best regards

Hello! I have bought a nice second hand DSC wired panel (PC1864) and is looking for some detectors. I am among other things considering the https://www.securitywarehouse.co.uk/catalog/rokonet-shocktec-with-magnet-white-p-620.html As I understand it this unit does not require any external analyzer card or anything and should work as any stand alone wired detector with my DSC right? I am thinking on using it for the doors on my house - do the main part of the detector in this case need to be mounted on the door itself or will it detect vibrations from break ins even if mounted on the frame? Do this unit have space internally to mount resistor? Do you have some install…

Require a ADE G3 Accenta Remote Control Pad that works in conjunction with a Jenko board. Would the current offering which you offer [ADE G3 - 4] that works with a Optima Board work with the Jenco board?

I have the following product I purchased last week - A073-00-01. It keeps throwing up RF Jam alerts. Is it possible that this can be faulty?

Dear. I try to install KP-250 PG2 to my Powermaster 30. But the cetral unit only say: "Wrong ID". What shall I do?

Dear Sir, I am looking for a wireless intrution alarm for a family house. I would like to have features such as, remote control frorm android or ios, GSM, camera display remotely. I live in Sweden and the alarm needs to support the EU standards so that it can be connected to a local security service if the alarm goes off. Would you recommend an Kit?

I am looking at purchasing a home alarm system for my house. My friends here in Sweden recommend the Visonic line. I am looking at a package to include the following: PowerMaster-33 G2 or PowerMaster-10 G2, could you please help me with what the pros and cons would be between these two? 1 x Internal GSM-modul GSM-350V21 2 x Wireless cameras (NEXT CAM PG2) 3 x Wireless magnets (MC-302 PG2) 2 x Wireless smoke detectors (SMD-426 PG2) Touch-panel + 3 tags either KPA-160 N PG2 or KP-250 PG2, could you please help me with what the pros and cons would be between these two? 1 x remote control Might also be interested in one or two outdoor cameras or motion detectors with lights

We have Optex FX-59 QZ alarm system which now it says to replace batteries however there are no batteries inside the sensors and in the panel. What are we supposed to do in this case? The alarm went off and an orange light keeps flashing.

Can you tell me what wireless portal is required for the galaxy dimension 520. Thank you.

Can you provide visonic power master magnets to compliment the visonic shock/vibration sensor making it a shock/contact sensor?