Intruder Alarms

hi I have an accenta G4 which I purchased from you a while ago I never completed the installation due to illness, but now after a break in I decided to complete the installation. I have got to the point of setting up program but I get tamper fault lockout, I have checked all cabling and have even put link wires on all tamper circuits even the one on the lcd keypad. but I still get the same message. I have also made sure the panel spring is pressed, I have done a complete factory restore but still the same. do you have any ideas for me to try ? I am happy to replace the panel if it's faulty but I don't wish to waste money if it is something else. thanks in advance

Hi. I'm trying to find a light beam sensor to work on a driveway, to send a signal to my house when a vehicle or person breaks the beam. Can be hard-wired or wireless - the location is about 120m from the house - the back entrance to a farm. I think you must do such devices but I can't see them online.

All has been fine then about a month ago while setting it l received the message open zone 5 l don't know what have caused this. Have you any ideas? That zone is on a PIR Its a Honeywell lS3012.If you think l need to purchase a new PIR let me know or could it just need re programming?

I'm currently self-building a house and am trying to decide on the alarm system (wired v wireless primarily) We have a pet (uses ground floor only) so PIR may be an issue. There are 3 doors (entrance, back and bi-fold) and 9 ground floor windows, plus 2 upstairs by a flat roof. I think I'd prefer wireless if possible, but I have a detached garage with games room above (1.5m from house). I also like the Texecom flush control panel - can you connect 2 of these? Can you recommend a system please?

Hi, Just wondered if you could tell me please how to change the volume on the 16 ohm speaker? I have one but can’t figure it out. Are they just one volume or is it changed at the panel? There is no adjustment at the keypad. https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/sounders-c-36_45/internal-sounders-c-36_45_139/secware-16-ohm-internal-speaker-tampered-grade-3-p-5040.html

Well, the Honeywell ADE Informa speech dialler I bought is to replace the current AD2000 speech dialler that is not working any longer. The speech dialler is to be connected to an Ademco 4204 relais module (with 4 relais) which in turn is getting its pulses from a Honeywell Vista 50P alarm system. So, basically, when there is an alarm in one of the 3 partitions I have in the alarm system (the Vista 50P), this triggers one of the relais in the Ademco 4204 which in turn triggers the speech dialler which then calls the phone of the home owner. The problem is that the current AD2000 speech dialler is connected to the Ademco 4204 relais with two wires each while the Hone…

Will Fike Sita ASD Detector with Sounder work with ADE Honeywell Accenta Mini Gen4 with LCD Keypad 8SP399A

I am replacing old ones of these. On the existing Optex EX-35R units is a sticker 869Mhz When I get these new ones, howh do I 'pair' it to the existing old Tunstall control unit, or how do I set the frequency to 869Mhz? Cheers in advance.

We currently have a Karisma Plus wired system installed. There are 9 zones. It is getting creaky, I have repaired it several times, time for a change. Our Ancient house is not good for wifi, so I want to stick with a wired system for reliability, using existing wires as these are hidden. The Karisma uses a 3 wire id device, which made wiring and set up easy. Is there an equivalent today? Or what do you recommend? Integrating fire detection / alarm would be useful.

Will these Optex Battery Powered 4 Channel Synchro Twin 30m Active Beam work with The new Visonic powermaster GTX kit https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/active-beams-c-36_142/optex-battery-powered-4-channel-synchro-twin-30m-active-beam-p-3371.html

HiI have been asked to install/add 2 Texecom AEB-0001 Impaq Plus Shock Sensor to a Scantronic 9448 alarm panel. (18 months old)There are 4 spare zones so that is not a problem, my question is will the 9448 panel support these type of Shock Sensors or could anyone recommend a more suited Shock Sensor?I will be glad to hear if any one thinks the panel is not suitableThankyouRichard

I am after a bit of help. I am looking for a wireless alarm recommendation. I normally fit a mixture of texecom and Honeywell hard wired system, but looking for a wireless system. Just a few requirements : Decent looking keypad. Bell box with illuminated back light Ability to send activation via internet. Thanks Ryan

do you know how many Texecom Impaq SCcan be connected to one zone on an alarm panel

got around to installing the pyronix twin alert and the bell output is nice and loud but the spk just clicks? I have it set on a entry/exit output on a galaxy G3 panel and have moved the volume control. To debug I moved the wire I have going to the bell side to the spk and it don't sound? I even tried using the pull up resistor, still didn't work... I know I was somewhat brain frazeled by the time I got to do that (I even wired a sensor to the wrong zone lol) and wondering if I have missed something.. +12v -0v Spk switched to 0v Bell switched to 0v

Hi, We are looking for a UL approved device and the Honeywell unit does not have that, please see my full specification below Our application calls for motion detection within a space (floor area of max 6mx4m) mounted at a height of nominally 2.5 – 3m with angle and rotational adjustment to optimise operation. Hence the request for the Bosch mounting bracket. We only require a single relay contact for detection of motion. (switching duty 24Vdc at < 10mA) PIR supply 24vdc operation preferred if possible, if not 12Vdc operation is OK. This application is for the US market and UL approval is specified. Hence the initial request for the Bosch PIR. Tamper faci…

i've purchased a Honewell 8EP416-EU to replace the RCP on my C&K Securit 800L. Please would you confirm which connections (COMMS and SOUND) correspond to C and D on the old Securit RCP? Thank you.

would the Siemens IMKW6-10 wireless contact work on a Europlex signet 200 alarm panel.?

Hi Is there a key fob option for the RKP. Thanks For your help Enjoy the weekend.

Could you please tell me how I can pick the updates for the newer panel with the new display panel coming up to date

Would it be possible to use a Voltek 1803 alongside a Takex PR11BE Beam?

we are searching for Flush mount type magnetic contact EN 50131-2-6 compliant, Grade 3 type do you have any?

We are Electrical Contractors (had products from SW in the past) normally install bells only systems but we have been asked us to replace an old system. (monitoring not required)customer ideally want a hard wired system planning to use Pyronix KX15DT`s and Pyronix Databell Plus My question is what would be a suitable control panel 8 zone minimum with 2 RKP`s which will allow programming etc with a Smart or Android phone ? Thanks Richard

The problem seems to come from the battery supply from motherboard no power to charge battery so flat battery will the unit need to be replaced

I'm looking at buying the dualcom complete with 1 year monitoring but I'm just wondering how that works who it's monitored with etc Do you guys do all the applications etc as I'm not a registered installer with them Or do they just liase with me direct? It's just to figure out who the customer would be. Me or the end user. Many thanks

Is this the only Guardall concentrator that you stock and if so is it compatible with the PX range of control panels?