Intruder Alarms

Hello there i recently purchased some optex -70 sensors from yourself for replacement of the obsolete optex 100 plus ones. On going to install them I found that the old ones have more wires eight as the new 70 ones only have six. So I was looking to see if there is a way to convert the old ones to the new

i have a client with a texecom 48 and wants some smoke detectors now some people say run alarm cable but i would of thought it be better to use the red fire rated cable?

Hello could you please help me with how i would wire the The 12 Volt Relay Base, 45681-508 to aTexecom PREMIER ELITE 48 8 ZONE CONTROL PANEL please

Can i network 5 different systems together with this panel? 16:00 Im thinking, have 1 as a master and the others a slaves Honeywell Galaxy Dimension 520 Control Panel Only C520-D-E1

I'm looking to replace a Scantronic 9853. Would the Eaton I-On interface with the existing PIR's etc? what the most suitable replacement would be as this panel is not in production now.

I am replacing an old system which is armed on exit using a shunt lock, I require a similar wired system. As we have a number of keyholders we prefer the final lock to arm / disarm the system in preference to a keycode

I require an alarm system that has the capability of giving 2 outputs to a relay to indicate Set/Unset and Alarm sounding. there is only a requirement for 4 zones (2 door contacts and 2 PIRS), an external bell box and we need 2 keypad i have been looking at the Texecom alarm systems as we are familiar with these. can you advise which model would give me the above requirements.

A number of years ago I purchased a Honeywell Galaxy 2-20 Wireless starter kit – Part # C020-01-C from you. • Software Version 1.44 • Hardware version 1.00 I’m considering purchasing the following products to give me access to the alarm on my local Ethernet network: • Honeywell Galaxy User Management Suite (Network enabled) - Model: R058-CD-DG • Honeywell Galaxy Ethernet Module - Model: E080-08 Can you confirm that the Ethernet Module and Software are compatible with the Galaxy 2-20 in its current Hardware and Software configuration? If a firmware upgrade is required please give details.

I need a replacement control panel for my Securit 800L alarm. Please could you tell me if you have one or suggest a suitable replacement.

will a Texecom premier elite RKP Model number DBD-0129 Work on a ADE Honeywell Accenta Mini Gen 4 control panel ? As i have 3 lcd RKP at the moment, and i want to up grade them.

I need to buy one of the Texecom Premier Elite alarm panels (plastic case) and wanted to know if they have the latest Firmware v4.02 on them. My current Premier Elite 24 met with a slight accident after a mains power surge and it's destroyed it, so I want to replace it with an identical model. It will be much easier to replace and I have just wallpapered around two remote keypads. If I order Tuesday, is there any way of getting one before Saturday to a CH43 post code? I have dual sounders outside (front and back) and don't want to annoy the neighbours any more, so will have to replace it at the weekend. I'm also looking for something like a power surge adapter for th…

I'm seen your texecom starter kit - New Texecom Ricochet Kit 2 64 Zone Wireless Kit with Sounder. I want to buy a texecom direct wired bell box. Can I wire that into the control panel for this kit or will it only work with a wireless bell box? Does the Texecom AEB-0001 Impaq Plus Shock Sensor Grade 2 work with the New Texecom Ricochet Kit 2 64 Zone Wireless Kit with Sounder. Also is there an option to have the system txt me when its set off?

Please advise what is meant by - A siren can only be learned in starting version Y51.

I'm having some problems in getting the CQR SC517 to work with the Premier Elite 48 panel. 5 contacts work as intended and they are setup the way that I cut T1,T2 and the red wires giving the correct restiance towards the Texecom (Double Pole / EOL), in Wintex they work perfectly. 10 contacts do not work, gap is the same between the contact and the magnet 6-10 mm. The do not work, same resistors are cut. In Wintex they report tamper alarm. Any ideeas ?

Normally fit ADE Honeywell control panel with LCD remote keypad. New Customer Installation. Customer wants to be able to set alarm with a proximity key. What would you recommend.

The 6 stand-by batteries in the main panel are not being trickle charged. Replacing them with fully charged new ones (1.37V) gets the system working correctly in all respects but only for approx 3 hours. The cells are then down to 1.2V off-load. Have you any information regarding the charging circuit that could allow me to investigate further and possibly repair? Your website indicates that the Homelink 75 is “sold out”. If I need to purchase a replacement system can you please recommend a suitable model Having had further time to think, it would seem logical to assume that the panel’s internal power supply is not producing anything at all - not just the battery charg…

Hello, Can we assign different sirens (I want 2 sirens) depending on the zones or suites on Texecom Premier elite 44 or more.

Recommendations for a keypad and fob activated alarm system with 1/2 motion sensors and 2 door switches compatible with the master blaster 127db alarm siren

I would greatly appreciate if you let me know if the above mentioned receiver can convert my existing hardwired Cisco 601 allarm panel sytem. If so, do I need additional devices to make it fully controllable by mobile.

Hi, i recently ordered some extra window/door sensor and an external siren for my Visonic Power Master 10 ADT Branded alarm. I have added a few sensors in the past with no problems but both door switches and the siren will not communicate with my alarm panel. When I add the device and press the auto-acquire button on the new sensor the panel tells me it is not a compatible device. So i tried entering the 7 digit number and now the panel said it is not registered on the network. Thinking it may be my panel at fault i tried to register them on a neighbours panel with the same results please advise?

We need to alarm our allotment warehouse. The insurance does not require an alarm but the committee fell we should spend a little money on a few basics. As a retired control electrician, just , I have been tasked. I require a mega external klaxon internal sounder 4 zone decent control panel 3 good vibration detecters and analyser 1 or 2 dual tech detecters cable Could you put a package together with price

Can you please advise a suitable alarm system that is wireless but has a wired siren?

I’m currently considering renewing my current wired alarm system (9450) and increasing the zones to at least eight, as offered in the Secware ADE LCD Accenta 3x Optex Saver PIR starter kit. I’ll be exchanging the external bell sounder which this kit appears to accommodate all those requirements, I’d also like to exchange my two battery operated smoke sensors to wired units. What can you suggest or recommend any other?

Hi Trying to programme a FAAC fob to a set of gates to a Bentley Bentayga. I understand that the code changes every time, would the below device work and would it be something that I can install? https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/intruder-alarm-ancillaries-c-36_46/pyronix-standalone-receiver-enforcer-series-twoway-radio-p-4552.html Many thanks.

I have a former ADT monitored alarm and I need to purchase a few more accessories for it. It is a Visonic Powermaster 30. Somebody told me that not all the Powermaster accessories work with the ADT alarms. Is this correct or will the PIRs and contacts you sell work with the system?