Intruder Alarms

is a prestige QD PIR compatable with a Texecom Veritas control panel, with the corrct value of ELO resistor added at the connection terminals?

Please can you tell me if Optex FX50QZL PASSIVE DETECTOR is a dual technology PIR sensor?

Hi, i bought a powermax plus alarm, and have just attached the external sounder to complete the system (risco novagard6), however, upon arming and disarming using the keyfob, the external sounder sounds for 1 second. this doesnt happen if i use the keypad on the pm+ though. Please could you point me in the right direction.

re: Honeywell Intellisense IS215T. We would like to replace all motion sensors in our house with the IS215T. There are approximately 20no. Can we simply buy these and connect up to existing wiring? Do we need a new control box?

I have fitted a wired intruder alarm system within my house and wonder if you could confirm I can install a wireless detector in an external building with a wireless receiver next to and connected to the wired system panel. If it is possible could you suggest the equipment I would need. There are spare zones on the wired panel and I would only need one zone on the wireless receiver.

I have an Accenta Mini 8 G3 alarm system. I need a new key pad. The original one 8EP219 I am told is out of date and been replaced with 8EP416. Can I change the keypad to the new one with no problems or is there likely to be compatability issues?

hi i have a job for an alarm system in a barn with no heating and damp/sub zero temps. the barn has two doors one sliding and one side entrance/fire ext. it has mains electric for power supply. also want a gsm dialer for the system. i cannot find a system that will be ok with the damp conditions. please advise, kind regards

which pir is suitable for scantronic 9449 burglaralarm

Hi I purchased a security panel, Texecom Premier DC8 + a few years ago from yourselves and I am only just fitting it but have mislaid the remote key pad and installation instructions. Can you advise which remote keypads you sell that will fit this panel as I note it is not for sale any more. Also, do you have the installation instructions available? Thanks

I wish to buy pir for above alarm can you tell me which is the right pir for this alarm

hi i have just installed this panel to an exsisting system, it has 1 door entry contact and 2 pirs 1 on the route to the panel the other at the back of the house. i conected the door contact to zone 1 the pir on route to the panel on zone2 and the other to zone 3 i am using program 1 and set zone 2 as timed inhibit the problem im having is when i do a walk test zone 1 triggers zone 3 and visa versa zone 2 triggers on its own fine. so if i set the alarm as i trigger the door contact (zone 1)before i get to the panel the alarm activates so i enter the code to silence and zone 1 & 2 are solid and 3 is flashing the door contact is only 2 wir so i cant have wired it…

Hi, I had an alarm system and we started having problems with our bell box (kept going off because it was too close to the boiler flue). I decided to replace the bell box and bought a Texecom Odyssey 1E. We've fitted the bellbox but it won't seem to work with my existing system. I'm not sure but it may be that its not compatable with the panel/key pad. I could do with knowing what panel/keypad would work with this bell box, how much they cost and whether you stock such an item. Thanks

looking for compatible door sensors, keypad and key fobs. have noticed that the key fob is sold out

We moved into our house previously without pets but with one of the above alarm panels. I need to replace three PIR with pet friendly ones. You advertise the Scantronic 430, is this compatible with the 9450 panel. Also I wanted to install a dialler but it seems that you are out of stock of all diallers. If there is one that is compatible with my control panel could you please let me know. Also I would like a clue as to how to wire up the dialler to my panel. Please feel free to answer any one of the points. The main one being compatibility.

We moved into our house previously without pets but with one of the above alarm panels. I need to replace three PIR with pet friendly ones. You advertise the Scantronic 430, is this compatible with the 9450 panel. Also I wanted to install a dialler but it seems that you are out of stock of all diallers. If there is one that is compatible with my control panel could you please let me know. Also I would like a clue as to how to wire up the dialler to my panel.

Hi, Could you please confirm if the following batteries are suitable for the Optima Compact Gen4 and if they will fit into the enclosure ok? They are both made by Yuasa but one is cheaper, so what's the difference and which is the better one? http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=350 or this: http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=1339 Also, could you please confirm if you have both the Optima compact in stock and either of the above two batteries? Finally, if I order today, when can I expect delivery? Thank you

Hi can anyone help me, I have installed this alarm system myself and i can set it fully,however I cant part set it. I have gone through the programs ,program 1 does everything,program 2 i have set up to just do downstairs. I have gone through the manual and done as it says, but when i set the alarm it says that once the code is typed in and the countdown begins press 'P' and the tone will stop then press the program you wish ie. 2. But for me the countdown doesnt stop, I press 'P' and 2 and it does nothing and it still says program '1' on the LCD keypad. Please help before I use a hammer on it as it is very frustrating!!!!! Please help thanks

I have fitted the above on a upc window. 1. the led is continuously flashing. Is this correct? 2. The unit is fitted to the position A at right hand side of the frame and will alarm on tapping the right hand panel but not when tapping the left hand panel. Are two units required on the window frame?

We have a customer looking for an outdoor 433MHz wireless PIR detector to add to our V003 GSM wireless alarm system. We don't offer accessories so wondered if you have something that may be suitable.

i am after a scan 9943 with 5 or 6 remotes. Will the keypad pair up ok with a 9930. How much is a 9941 & 9943 & fobs

I have purchase from Security Warehouse an ADE Honeywell Easy Set Unit with an ADE Honeywell Accenta Metal Gen 4. The instructions for the Easy Set provide Wiring Details for connection to a G3 and an Accenta 8 Panel, but there is no wiring and program changes for a Gen 4. How is the wiring configured and what program changes are necessary. Our Reference Secware 3 sent 19.45 on the 5th of November.

Can you tell me if there is any benefit to having an mcs-730 over a mcs-710 other than being 10db louder?

can you tell me dose the snt duolink kit come with psu

Does the Honeywell AG6 SAB and Cover (Blue Strobe)have led indicators on perm or flashing, to indicate power is there and it is not a dummy box.

upon power uo of my recently purchased optima gen4 copact alarm the alarm sounds- enter code 0123 and the alarm siren silences. i have no flashing tamper light despite the cover being off,i have a flashing sos led which will not go out whatever i press? i have the global tamper pa & ta terminals shorted out but still am unable to extinguish the sos led. do you think the unit is faulty or am i missing something obvious