Intruder Alarms

Just got a question I can't seem to figure out. How do you program Part arms on the Wintex software? I would like to activate a Night arm or Bedtime arm.

Hi, Just to be sure, how do I wire the SECWARE BCINTRA/W/B to the Texecom Premier 88 panel? Like Texecom - Secware 12V + = 12V + 12V - = 12V - Bell - = ? Tamp = ? Strb - = ? Do I need other connections e.a. strobe to 12V+? And do I need to set some settings in wintex to work? Thanks in advance.

Hi, I have just bought from you the Honeywell galaxy g2-12 and mk7 keypad, Honeywell 8IR150 pirs and AG6 bell box, plus Knight G2 5 door contacts. Can you please advise how to wire a pir at the pir end and panel end and where to place resistors. The g2-12 to keypad appears straightforward but does it need a resistor at the keypad end between A and B. Also do all unused zones need a resistor across them to terminate. Could you also confirm bellbox wiring to panel.

After a mains power failure all the alpha numeric characters have disappeared from the LCD display with only the top line of the display now showing black rectangles. Is there a system component failure or can the display be recovered?

I have a question regarding one of the configuration settings on the NEXT PG2 The 'Disarm Activity' setting has a number of options including: Not Active, Yes-No Delay, Yes + 5s delay...etc I am confused about the 'delay' setting. What does the 'delay' value relate to, i.e. the delay between what and what? Also, in what type of scenario would the device be configured to be 'Yes + 30s delay' for example.

I would like to upgrade our Galaxy 512 with Ethernet module in order to control the system remotely and to when need be, handle programming and updates through Internet interface, rather than using one of the MAP's in the system. My understanding is that this could be done by complementing our existing system with an additional Honeywell Galaxy Ethernet Module (Model: E080-2) from you, and also I guess, I need to upgrade the SW that currently running as that is an old version, - Ver. 1.27. Our Galaxy 512 motherboard is Rev1.6. Pls. let me know if my thoughts are right, and if so provide me with the pricing for the ROM/EPROM for the SW upgrade, and if needed any ad…

Thank you for fast delivery of my order. I am contacting you because I have a problem on Menvier detectors M12 I wanted to test the outbreak with a hairdryer and the contact does not open. The light and red but no alarm on the alarm. I have checked the jumper everything is good. I have the problem on three sensors M 12 is really weird is it not?

I purchased a SD 3 dialler off you approximately 3 years ago. It has recently stopped dialling out when the alarm has been activated. I checked the Sim card in a mobile phone and I was able to make calls from the phone, to double check I also bought a new sim card which again worked in my mobile phone but would not dial out from the SD 3. In the LCD display , next to the temperature there is a small box with a letter T in it. The sim card I use is a Tesco pay as you go, signal strength is the same as usual. I have tried to do a test call from the dialler and it failed with the message call error. When I have dialled in remotely the sim goes straight to answer phone , I wa…

I bought a Visonic TOWER-20AM MCW Outdoor Motion Sensor on your web site in November 2012 and I had 4 false errors in the last 2 days. The message that I received on my phone each time is IRP MASKED ! First time I was home and nobody was outside in the Sensor area. The Sensor worked fine for more than 6 month and nothing change on the configuration. I don’t know what to do, could you please help me with that or explain me who can help me ?

My question is this. Are all the biscuits in an 11-20 blue-pack (as above) the same, apart from the numbered stickers, or is the internal wiring different? I ask because I've just broken a No 20 while attempting to replace a doorbell plate. Can I use another biscuit from the same pack as a replacement, or will this upset my alarm system? Sorry if this is a stupid question, but I'm no expert. I've asked for high-priority because my house alarm is disabled by the problem.

is there anyway of turning down the volume of the ADE Honeywell MSN Multi Siren MS-N on the entry & exit of alarm?

I am unable to enrol the KP-141 PG2(June2013) to the Power Master 30 alarm system(Nov2012): - Full enrolment procedure: I select the * key on the keypad until the LED turns on and then release the * key. The Power Master 30 alarm system (i.e. Add New Device -> Enrol Now) indicates on its display, "Incompatible Device". - Pre-enrolment procedure: I enter the Id of the device into the Power Master 30 alarm system and it is accepted (i.e. Add New Device -> Enter Id). However, the Power Master 30 alarm system indicates that the keypad cannot be networked.

hello just purchased this extra vx-402 and I am using it as a slave of another 402.the problem it will not detect a intrusion.it clicks it flashes but no sound to the alarm panel.what am I doing wrong?could the 402 be faulty.

I was wondering if the Powermax Pro kit you sell supports Partitions? As the description says its optional. Thanks

I assume with the keypad I 1. open cover 2. disconnect wires (making note of what goes where) 3. wire up new keypad 4. replace cover, enter user code and test alarm

The systems re-starts itself making impossible to use is as it fires the alarms every time the systems re-starts. The system installation was installed about 2 weeks ago and at the beginning, about every day, at any time (middle of the night or right in the afternoon) the systems alarm was on but with NO intruder detection as the system was NOT armed. Watching the log events, every time that it fails, shows “START UP” and “MAINS OK” and the LCD Keypad shows new date and time as when start up for first time (like default factory data). With this information, I understand that power is being lost for some reason so I changed the main power supply connections just to make …

I bought a powermaster 10 kit and i have a auto test alarm thats sends to my phone on strange dates (23-10-12, 07-01-13, 03-04-13). I have looked everywhere in the menys but can´t find any autotest meny with that kind of options of dates?? Also my powermaster hums alot from the Power unit, is that normal?

I see two mobile com modules TEXECOM. (type 0001-jae and cegb 001) What's the difference? There is a big price difference. I recently bought a 48 premier installation TEXECOM elite with you. The intention is that the alarm via mobile redirected to mobile. Additional question: To how many mobiles he can send the message and it is only a text message or voice?

When I install it, where it is supposed to be, it goes into this tamper alarm mode and it does not help to remove and then add the device or removing the battery, keeps staying in the tamper alarm mode. Have ran out of ideas. Any suggestions on what to do about it??? It is only one contact and it enrols fine and I also suspect its something with the tamper switch, but have not figured out how to reset the switch. Thought it was enough to put back the cover but apparently there is something else that needs to be done. Could you please explain how to 'reset' the tamper switch after it has been violated?

Scantronic EXCELR 12m Wireless PIR will this work with my scantronic +500r panal please advise the frequency your help would be appreciated

I would like to exspand the system I have,which is PA 4 WIRED alarm (Friedland)to ad to the system with two OPTEX SAVER NEW QUAD PIR. Would this be suitable.The movement detectors I have,have got 6 connections in it.

Hi I am looking into buying a Visonic home alarm system Is it possible to mount a curtain detector across a room, i.e. creating a wall (a foot inside of a number of windows), even though there might be chairs etc on the floor?

I have two garage doors, roller shutter style on my house in need of connection to the Visonic powermax complete system installed. Is it possible to use the "MCT-100" connected to a couple of "Knight Plastics F10C Roller Shutter" or do you have some other recommended solution for garage door protection?

Just bought a Veritas panel from your good selves and am ready to fit. Aftr reading the enclosed paperwork I want to know if I need to change the dip switches (it will be the only one apart from the main panel) and do I need to configure it for 'Network devices'? If so what do I have to do?

Hi I need to purchase a wireless alarm system with proximity entry I have looked at the powermaster visonic range but need to know if the powermaster 10 panel has an internal 12 v supply outlet so I can add my already owned gsm dialer.I have seen that there are two proximity readers in the powermaster range the kp 160 and the kp 141 which is the most suitable and easiset to use and are the proximity tags an extra with these items