Intruder Alarms

iam looking to buy a 800l control panel but i have noticed that they are sold out any chance if you are going to restock them

I purchased a Powermax plus alarm system from yourselves 3.5 years ago. Has been working fine, but I seem to have lost the Master User code, I did change them from the default. It has been working perfectly but I now need to remove a sensor from the system. How can I reset the codes. I tried the jumper reset but this had no effect.

last year bought Honeywell ADE LCD Accenta from you website want to add: Honeywell Hard Wired Carbon Monoxide Alarm Honeywell Combination Optical/Thermal Smoke Detector (58°C~) Honeywell Combination Rate-of-Rise/Thermal (58°C)Smoke Detector. are the above compatible and do I need bases for the fire detectors and can I add a 12Volt 7Ah battery instead of the 2.3Ah exernally (outside of the panel)

I am looking for a home alarm system for both security and fire / carbon monoxide There are three bedrooms on the top floor, downstairs there is a hallway leading to the front door, a combined lounge / dining room 25m2 with windows at either end, kitchen with door to outside and a bathroom with a large window. The lounge will need to have a carbon monoxide detector fitted as it will contain a log burner. I would like to be able to mount the control unit away from the key pad and may in the future wish to add another keypad to go in the kitchen. I am very happy to have a wired system and install it myself as the whole house is being renovated at the moment but would w…

I need to fit 5 hard wired fire alarms in my house as part of a loft conversion. I bought a Scantronic 9751 based burglar alarm system from you a few years ago. Do you supply fire alarms that can be hard wired into this system?

Hi , about to place order and wondering main difference between accenta mini panel gen4 and standard poly gen 4 (other than size)

I bought a new DT7550UK2 from you last week to replace an existing faulty one. The existing one is a DT7550UK so assume this must be the older version. Looking at the existing wiring, it is wired as follows F1 - empty F2 - empty T1 - resistor to C T2 - yellow C - resistor back to T1 and to NC EOL - empty NC - resistor to C and blue V- - black V+ - Red Both resistors have the following bands (Brown, Black, Black, Brown, Brown) or I guess could be (Brown, Brown, Black, Black, Brown)? Looking at the installation instructions for the new one, it implies I should not use the existing resistors and wire up as above. Is this the case? Also, will the factory …

is it possibe to part set a system, silently, using a Honeywell easy set with key fob. If not , how is this acheived. I want to set/ unset the ground floor from the first floor, in the quickest and quietest way.

I can't find any Wired Siren for my Powermax Complete alarm. Do you have one, or could you recommend one?

I am looking to upgrade the security at one of our premises using a Net enabled alarm and CCTV system I note one option is the new Honeywell alarm system in the Galaxy range , assuming you cover it, could you pl update the costs for the model called Galaxy Flex. Also wanted to know if you have option to connect outdoor IR Sensor at the perimeter, to these alarm system. My local engineer told me that I-on 40 that you offer can be connected to these systems, eg BX-80N or NR model from OPTEX. Can this also be connected to galaxy model eg dimension flex etc

I am a building contractor with a number of sites in operation. I am interested in the GJD GSM Autodialler or Pyronix V2 GSM. Can these products be used as standalone alarm units. Can PIRs be connected directly to this unit or do I have to integrate this with an alarm control panel?

Hi I want to use the Visonic Discovery Quad wiireless detector to protect a garden shed approx 25 meters away from the panel. do you happen to know if this particular wireless item is relaible or would you advise using hardwired ?

I am interested in the wireless detectors for my home. (outdoor) Blueline PIR Detector We live on a very large property with three large dogs in the garden. 2.What I would like to do is divide the property into 4 security zones which can be armed and disarmed independently. I was thinking of placing about 4 or 5 detectors in each zone. Could you make any suggestions? Do you think that the above detector will be right for me? Next, I would like to hear your opinion about the receivers and/or control panel that I would need? The control panel (alarm system) should be armed and disarmed by using a remote control. My other concern is that we often experience po…

When will you be able to sell the new MK 8 keypad for Honeywells Galaxy-range?

i've been looking at these keypads here: http://www.securitywarehouse.co.uk/catalog/texecom-premier-elite-keypad-p-2481.html You talk about SMK and FMK, is this kit suitable for either surface or flush mounting?

About to place an order but wsh to enquire if the maximum battery size for ADE Honeywell Accenta Poly Gen 4 with LCD keypad is it the 2.3 amp Enersys battery or will it take the 3.4 or 7.0 amp battery.

I want to buy the new Honeywell Galaxy Flex - are you able to supply it in a package like you have done for the "Honeywell Galaxy Dimension

Installed above alarm several weeks ago, the one only problem I have not been able to resolve is that there is no option to part set the system using program 2. Program 1 is the main program so I've set up program 2 so the landing pir is not used and intended to use this program at night. The instructions say enter CODE press P and select program number in this case 2 but I press number 2 but nothing happens and it stays set on program 1. I also have an LCD keypad upstairs for use at night. One thing the instructions say is that "the installer has to program the system for part operation", I presume this mean program 2 has to be set up which I've done or am I missing s…

Hi, Do you also sell the door contact and smoke sensors for this? Do your prices include VAT? How much is UK delivery? (looking at the kit and 3 PIR's) thanks

Dear Customer Services. Please can you give me a price on the following Texecom keypads: Premier LCD - code: DBA-0001 Premier LCDL - code: DBB-0001 Premier Elite LCDLP - Code: DBD-0168 Thanks

Hi, can you please tell me prices of the below: 1 x Visonic Powermax+ 1 x Extarnal GSM adaptor 2 x Wireless motion detector (works in dark, no pet) 2 x Wireless door/window 1 x Wireless Glass-break detector 2 x Wireless smoke detector Can you estimate the freight to Sweden?

Hi, I already have wired system with panel, 6 wired PIR and bell. I'm unsure what make/model existing panel is, but what I'd like is new panel to do is: - allow remote access to arm,/disarm and check alarm status (web/app/gsm) - connect existing wird PIR and bell (if possible) - have ability to set different zones. Currently have home zone and garage zone. When out and about we arm both zones; when home we arm just garage zone. - allow new wireless devices to be added Thanks,

Hi I am installing a accenta Gen 4 system .Its for a residential home for people with learning difficulties. Basiacllly they want the doors to chime and light up on the key pad until reset or another door opens . So the light is on pretty much all the time regardless of the door then being shut I am thinking of installing your "Elmdene EN3 QFC Grade 3 flush contacts red resistor " I just want to know whether these are compatible with the system . Ie I am not going to install them then a fault comes up on the keypad

Hello there, Could you, please, help me finding which of your system would be most suitable for my needs? I am looking for alarm system for the house and 2 wooden bike sheds 7 meters from the house. The system for house can be wired, the system for sheds must be wireless. The house system will need 5 PIRs, one of them should tolerate a tortoise (25cm, 2 kg, in a heated enclosure in the hall), 2 door contacts, 2 sensors for windows (breaking glass or vibration?). There are both, a land line and GSM cover, in the house. The system for the sheds should probably have 1 door contact and 1 PIR for each shed, PIRs could maybe replaced by vibration sensors attached directly t…

I have recently purchased a scantronic 9651EN-43 from you, the documentation says that I can connect fire alarm detectors, i.e. ion/optical, please can you advise which products and whether an interface is required.