Secware2

I require an alarm system that has the capability of giving 2 outputs to a relay to indicate Set/Unset and Alarm sounding. there is only a requirement for 4 zones (2 door contacts and 2 PIRS), an external bell box and we need 2 keypad i have been looking at the Texecom alarm systems as we are familiar with these. can you advise which model would give me the above requirements.

looking to send 3 images down 1 coax , similiar to Duolink , do you have anything?

Possible replacement for you: https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/security-control-panels-c-36_102/control-panels-all-c-36_102_41/ade-honeywell-accenta-mini-gen4-with-led-keypad-p-1544.html

Sadly not, you would need the Accenta RKP

Adapter link: https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/intruder-alarm-ancillaries-c-36_46/act-2323-230v-mainspike-suppressor-p-445.html

Please advise what is meant by - A siren can only be learned in starting version Y51.

HDD network recorder N5316QR-P Please can you send me some info and advise what size and how many HDDs i would need for this product for aprox 1 month recording Could you also advise which cameras would be best suited for internal and external use (dome cameras preferred)

Please find link below: https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/intruder-alarm-ancillaries-c-36_46/texecom-connect-smartcom-ethernet-communicator-cel0002-p-5212.html Due into stock 5 working days.

I have a PowerMAx complete wireless alarm system installed in the house. I was wanting to add an additional wireless siren (the system can handle a maximum of 2). I already have the MCS -740 wireless alarm and was hoping to purchase the wired version of this alarm, the MCS-730AC. Can you check for system compatibility. The version number of the panel is: JS702159 B.17.107 JS700421 V.1.0.02

Hi i brought galaxy g2 alarm panel from your store.i am going to add second mk7 keypad to the system.according to installation menual i need to use eol 680 ohm resistor at each keypad and connect them in daisy chain. Please can you tell me what watt resistors require. thanks

hi I have an accenta G4 which I purchased from you a while ago I never completed the installation due to illness, but now after a break in I decided to complete the installation. I have got to the point of setting up program but I get tamper fault lockout, I have checked all cabling and have even put link wires on all tamper circuits even the one on the lcd keypad. but I still get the same message. I have also made sure the panel spring is pressed, I have done a complete factory restore but still the same. do you have any ideas for me to try ? I am happy to replace the panel if it's faulty but I don't wish to waste money if it is something else. thanks in advance

I have motion detectors Next K9 PG2. They create false alarm due to small animal walking in the area, How can I configure in order to eliminate these false alarms?

Please find link below: https://www.securitywarehouse.co.uk/catalog/optex-vxist-12m-wide-angle-twin-sensor-outdoor-pir-p-3877.html

I believe this is now in hand with Visonic and they are helping with your faulty control panel, and not the keypad. However if support can be of further help please respond.

The Powerlink 3 is only compatible with SW version 18 upwards, so would depend what software your panel has.

For CAMIR please find link below: https://www.securitywarehouse.co.uk/catalog/honeywell-le-sucre-wireless-pir-with-builtin-colour-camera-p-4473.html

I am struggling to find information on how to wire the Pyronix Deltabell Plus to the Honeywell Flex 20. Also i would like to know how to wire the Honeywell DT8012F5 DUAL TEC Motion Sensor with Pet-Immunity (DT8012F5) to the Honeywell Flex 20 panel. At present i have connected the positive and negative to +12V and 0V. I have connected the NC to 0V and put a 1K resistor at the sensor to C, and then again a 1K resistor from C to Tamper. The problem i have is the sensor doesn't have a Fault terminal to wire to zone 1.

The GSM module would require a sim: https://www.securitywarehouse.co.uk/catalog/visonic-gsm350-with-gsmgprs-connectivity-p-2714.html All products are 868mhz unless stated otherwise, if purchasing PowerMaster products, these are only compatible with panels/peripherals purchased within the UK, as these work on a different frequency to the rest of Europe.

We always welcome feedback https://uk.trustpilot.com/review/www.securitywarehouse.co.uk

3. https://www.securitywarehouse.co.uk/catalog/honeywell-hcssms2y-sms-notification-services-for-2-years-p-4722.html

I Purchased a Galaxy Dimension panel last week. It didn't come with an installation or programming manual.I have found some information on line. But need a few answers if possible. What are the external bell box connections? What are the internal sounder connections? I have the system operating with a few detectors and the system has 1 fault which is because it does not have a telephone connection. Can this facility be turned of as I don't need this facility at the moment? If not what is the best way to clear this fault so the system has no faults and is usable.

Please raise a ticket advising order number, and we will be able to look into this for you. https://www.securitywarehouse.co.uk/support/ticket/upload/index.php

The Powerlink 3 will allow you to use the Visonic app and set/unset the alarm. However the PIR with integrated camera images are only available through a Monitoring station and not for the end user.

A two way system would help against false alarms: https://www.securitywarehouse.co.uk/catalog/visonic-powermaster-10-kit-p-2697.html Please see link for full Powermaster Range: https://www.securitywarehouse.co.uk/catalog/index.php?main_page=advanced_search_result&search_in_description=1&keyword=powermaster&inc_subcat=0&sort=4a&page=2

Contact a local installer, there will be a call out charge but they will be able to help you.