Intruder Alarms

Hello I have a Menvier TS700 and am looking for a replacement keypad, would you be able to source a TSNETLED or TSNETSTAR keypad ? Thanks and Regards Karl

I have a Paragon plus ,and I cann't get a replacement RKP ,Can it be replaced with any other make or model ,if so can you surgest a replacement Thanks Lawrence

Hi, I am experiencing odd behaviour with a Visonic Powermaster 10. Due to a planned extended power cut, the panel was unplugged for 24 hours, during which time the battery went flat. The panel was reconnected to the mains when the power returned and it eventually booted back up. Since then it has suffered 3 false alarms from separate PIRs. Should I do a factory reset to try to resolve the issues? If so, is the only option a hardware reset? When I open the back of the panel I can see three pins marked DEF and 3 marked RST. Which pins should I jumper please? Thanks in advance for any assistance. Mark.

Hi! I purchased an alarm system, a Viasonic Powermax+, from you in september 2009. Since we have 3 cats (weight 4,2 4,2 and 3,5 kg) I got the pet tolerant PIR:s. Tha alarm has been working perfectly until last night when we all woke up from the sounding alarm. When you wake up at 4 AM from a deep sleep and realize that the alarm you have come to rely on not giving false alarms, is sounding, you get up really quick, I promise. Armed with a knife and a steel pipe I searched the house but found nothing. Since we have a lot of snow I could also check for tracks outside the windows and back door, but nothing. I am 100% sure it was a false alarm and it was a PIR in…

I have to purchase the following equipment for a new house which already has cabling installed for an alarm system. 6 x Dual-tech PIRs (because of the geometry of the rooms some of these will be facing a window, which I can do nothing about) 1 x Door contact 1 x 8+ Control panel 1 x Keypad 2 x Internal sounders 1 x External sounder 1 x Bell box Plus anything else that will be required that I've not mentioned. I have identified the following:- PIRs - Scantronic 460; Honeywell Intellisense DT7550A & Eurosec V40DT Control panels (& keypads) - Scantronic 9651EN-43 & ADE Accenta MetalGen4 with LCD keypad (8SP419A) Are you able to:- 1)say which of…

When I install it, where it is supposed to be, it goes into this tamper alarm mode and it does not help to remove and then add the device or removing the battery, keeps staying in the tamper alarm mode. Have ran out of ideas. Any suggestions on what to do about it??? It is only one contact and it enrols fine and I also suspect its something with the tamper switch, but have not figured out how to reset the switch. Thought it was enough to put back the cover but apparently there is something else that needs to be done. Could you please explain how to 'reset' the tamper switch after it has been violated?

I purchased a SD 3 dialler off you approximately 3 years ago. It has recently stopped dialling out when the alarm has been activated. I checked the Sim card in a mobile phone and I was able to make calls from the phone, to double check I also bought a new sim card which again worked in my mobile phone but would not dial out from the SD 3. In the LCD display , next to the temperature there is a small box with a letter T in it. The sim card I use is a Tesco pay as you go, signal strength is the same as usual. I have tried to do a test call from the dialler and it failed with the message call error. When I have dialled in remotely the sim goes straight to answer phone , I wa…

The wiring diagrams are unclear for connecting the panel to the external sounder/bell box. The connections on the bell do not relate to the bell instructions. Can you tell me how to connect the two. On the ADE GEN 4 panel i have..... STROBE +VE STROBE -VE T A D B On the bell i have..... ST- R- SW- V+ V- Please tell me what connects to what........

Afternoon, I have recently installed an optima compact gen3 system in my house and added a remote keypad. The system is working fine and walk tests etc with no problems but whilst it is day made the remote keypad and main control box emit a double beep approx every five minutes (very annoying). I've gone through the operating manual and the engineers manual I have and it seems this would be the system telling me of a line fault for the communications system. However, as you as probably aware, there is no comms system on the compact panel. any idea how I can stop it beeping at me please......? Thanks, Neil Annals.

Hi, I purchased the above kit from yourselves just over a week ago. I am trying to wire the bellbox to the control panel, however, the connections listed in the Intellisense AG6 leaflet differ from those on the actual PCB. The manual lists TR- V- ST- V+ S- but the PCB has ST R SW V+ V- So can you tell me what to connect to where on the Accenta G4 panel? Regards, Warren

I have programed all pir siren contacts and tcu remote but when trying to set full or part set the tcu displays operation cancelled instead of arming any ideas please

Hello At present I have a hired alarm system (in Sweden) from Honeywell, the main central is a CMI8NE-SDI4G (with mobile as well as wired telephone connection) I will not renew the rental agreement when it ends soon, hence the CMI8NE-SDI4G will be returned to the company. All other Items such as one keypad (CSK8NE-SDI-, two smoke detectors (DTO600HF-, one PIR (IRX800HFCT- and one magnetic switch (DOD800HF- will stay as my property. I will like to buy a new main central and have found a CMI8UK-STD, will this be compatible with the items mentioned above, and can it all be programmed by using a TCU2-800 mobile keypad? Flemming

Hi, I seem to have my Gen 4 almost working as desired with my existing BG (DSC) equipment, however for the life of me I cannot seem to get the strobe light working. The Bell will work but not the strobe. The existing bell box wires where listed as (+) Red, (-) Black (which I have hooked both of these up to the bell connectors), AUX = Blue and Strobe = Green. Any advice/suggestions would be greatly appreciated.

Hi, I have recently naively purchased and installed a powermaster 33 alarm unit along with the IP Powerlink 3 module and a camera PIR. I thought it would be as simple as install, get it working, attach to the network and link with the app. I see this in not the case. Can anyone point me in the right direction? I have done some more googling and found from the visonic website links to the powermanage and powermaster interactive side of things. They mention having a CMS or remote management company... I just want to run some software from my Mac(which is on all the time) and access via the app... Any advice grateful Thanks

Hi, I installed the LCD panel yesterday. and the screen just froze a few hours after I set the alarm. The keypad was unresponsive and showing time and date on the screen. I powered the alarm off and when I reconnected it, the LCD panel was still unresponsive but the screen was showing Accenta G4 RKP F131-01-111 The keys are NOT responding. Any help? Thanks in advance.

This is similar to another post below, I too have a texecom veritas system which is faulty, I have called their support desk and there are unhelpful and ofter cut me off if they can't find a solution. I too am ready to replace, I have been looking everywhere and tempted to get a professional around to install a new system but prices are unjustifiable, four figures to takeover an existed wired system and replace the panels, I think I must be paying for the Nacass approval badge!! I am about replaced all my working PIRs with a Bosch BLP-1P pet friendly ones. I need to replace the system, the reason is the guy who installed it last year couldn't get the two bell boxes t…

I have not seen any on securitywarehouse product page but do anyone know of any other site where I can get normally open surface contact. are these passive or active(need power to work?) thanks

I have recently moved to this property which employs a 9427eur-80 rkp grade 1 fire alarm. Unfortunately there are no instructions on how to operate this alarm and I am wondering if you could possibly supply some information regarding it's operation etc. I understand that the house was built about 4 years ago. Thankyou in advance and wishing you all a happy new year.

Enforcer wireless alarm about a year ago which i purchase for you. this has been work fine. until just recently it came up with a battery fault. I have changed all the batteries in the sensors, and done a battery check and signal strength test, and they have shown as ok. the alarm has been working for a week since this, and now has displayed an error again of, unable to set 01 wireless low battery. I have done the battery and signal test again, and has come back as ok.

Hi I need to install a system to protect a secure shed. I dont want to spend more than

Hi, I am looking to upgrade my home alarm system and after reviewing your forum have a few questions that I hope you can help me with so that I order to correct system (and compatible components). Essentially, I have a new build with the developer fitted DCS Alarm branded as British Gas which seems to not meet any of my requirements. Basically I am hoping to upgrade this to something more usable and compatible with pets i.e. something that I can adjust zones (regions) as I see fit as the dog is quite large. I have contacted 3 of the larger installers in my area and given that two never kept their appointment and the other quoted just under

I have an A083-01 that was working fine in a Galaxy Flex 20 up until about a month ago when the panel started to report line failures. Despite several resets of both the Internet and the panel, the error would come back within an hour or so (line fail sensing). The diagnostics on the panel report that the comms are all good. The LEDs on the A083 also suggest everything is OK (Green on 0.1, off 0.9 sec) Orange intermittent = ethernet. If I disconnect the 435 cable I get an immediate error on the panel, so it is being detected OK.I’ve replaced the Ethernet cable, used a different IP address etc, all without change.However, I cannot communicate in or out via the unit. Rather…

Hi, I am going to upgrade my Galaxy G2-12 wired system to a wireless system. The list of components I think I need to purchase are in another thread where I was asking about compatibility :- http://www.securitywarehouse.co.uk/forums/topic/4414-ticket-question-wireless-peripherals-with-g2-12/ and are reposted here :- - Honeywell C079-2 RF Portal - Honeywell CP051-00-01 MK8 keyprox - Honeywell C072 Boxed RIO expander - 3x Honeywell TCC8M wireless keyfob - Honeywell SMB10 Motion sensor mounts - RS485 Bus wire : Twisted pair screen cable Belden 8723 equivalent - 680 Ohm resistors - 4x Honeywell DO8M - Door - 5x Honeywell IRPI8M - IR…

Just installed the Accenta G4 panel and all worked well. a few days later a fault occured to the entry/exit. Problem is break to the pair of contact wire. Replace with the spare and makes and break but the problem is the panel does not register open/close of the contact but ok with the multimeter. Another factor that I can assume is new carpet was fitted and wonder if the fitter damaged the cable which I think would be most likely as it was all working fine before the carpet was fitted. No short between contact wire and tamper wire. Any help would be grateful. I will run a temp cable this weekend and see what happens.

Hi, I'm fitting a Honeywell Galaxy G2-20 at the moment (4th installation of the galaxy range) and usually would just fit a dialler however i saw the CSL Dualcom for sale on SW:- http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=2438 It says that the first years monitoring is included, i'm just wondering who the ARC is, how the registration is completed and the ongoing yearly costs. Thanks Peter