Intruder Alarms

Hi, we are looking at the Honeywell EC01000 range of detectors. We require Optical & Ionization, can you recomend an Ionization Detector for the Honeywell Galaxy Dimension Panel and explain the diffrence in the standard and diode base. Am I right in thinking these have no sounder and if so what compatible internal sounder is available?

According to installation instructions for AG6 sounder PCB should be marked as follows TR- V- ST- V+ S- The actual PCB is marked ST- R- SW- V+ V- Can you confirm R- is actually TR- and SW- is actually S-

I Have A2Z detectors on alarm system and I would like to fit a CO2 detector also to alarm system I know A2Z no longer exist is there anything simular available you can use instead

I am unable to enrol the KP-141 PG2(June2013) to the Power Master 30 alarm system(Nov2012): - Full enrolment procedure: I select the * key on the keypad until the LED turns on and then release the * key. The Power Master 30 alarm system (i.e. Add New Device -> Enrol Now) indicates on its display, "Incompatible Device". - Pre-enrolment procedure: I enter the Id of the device into the Power Master 30 alarm system and it is accepted (i.e. Add New Device -> Enter Id). However, the Power Master 30 alarm system indicates that the keypad cannot be networked.

Ive been looking at the eaton cloud communicator for i-on control panels but im not sure if it would work with my control panel< i have a menvier 40 which is the same make but i would also need the adapter board, would you know if this would work

Just bought a Powermax+ with some sensors and a GSM module. I wonder if I can connect both the control panel and the GSM module to the same powersupply, thus reducing the number of wires needed. One possible solution would be to connect the power to the control panel, and then another wire from the control panel (2 wires at the same connectionpoint) to the GSM module. Another way would be to use some sort of "Y" connection to route power to both consumers.

Panel has become unreliable and believe it is the panel not the wiring. I have 12 proximity sensors, 12 smoke detectors and 2 heat detectors. I also have 3 remote access keypads with simple LCD display. I would like to add another 6 sensors. My questions are: Should I reuse the existing wiring? (its an old house and took a great deal of effort to fit professionally). Which system would provide the most intuitive fault finding? Which system / manufacturer offers the most scope for the future? Can I reuse all the existing detectors? Would ideally like to be able to look in from a pc or iPad to see status? Any comments or suggestions gratefully received.

hi, i have a 595 keypad that the fobs have stopped working (code numbers ok) ,that i installed 3 months ago,how do i go about replacing, do i need to buy a spare one, then ask for a refund on the old one , thanks

I have recently moved to this property which employs a 9427eur-80 rkp grade 1 fire alarm. Unfortunately there are no instructions on how to operate this alarm and I am wondering if you could possibly supply some information regarding it's operation etc. I understand that the house was built about 4 years ago. Thankyou in advance and wishing you all a happy new year.

Hi, I am having part of my garage converted into a small room with access only from a outside door. I would like to add this room to my 9448+ by adding a new zone. Can I add a door switch, movement sensor and extra keypad to this system? also I would like to set the alarm for this room at all times even when we are in, however we part set the alarm at night arming the downstairs zones. Would it be possible to part set the alarm and the new zone or will I have to manually omit the upstairs zones at night leaving the downstairs and the new room armed?

support/Elaine, is the 2.1Ah rechargeable battery included with 9448EUR-95 STYLE? thanks

Hello I installed a month ago scantronic 9651 the alarm goes in to fault mode When i read the log it states 'bad checksum' could you tell me what this , also it sometimes come up plug by communications is out , but i check the sd2 DIALLER it is functioning, line is ok If the same line is on a non filtered dsl telephone line could this interfere Thanks Mr Patel

I am looking to find the best option for a complex installation. Any expert recommandation on any of the following issues would be very helpfull and highly rewarded! - the system should accomodate wireless outdoor detectors incl. cameras for video/or image transmission to a surveillance company. - the system should be able to accomodate both wireless and wired connections with about 30 wireless units to be connected and be secured against external perturbation and shall be able to trigger a silent alarm in case of outdoor detection (incl. video or transmission to the surveillance company) and a normal alarm in case of indoor intrusion detection (also with indoor vide…

hey, I currently have an ademco accord security system installed in my flat and the transformer has stopped working. I have recently just purchased a scantronic 9448+ and i was wondering if i could take the new transformer from the scantronic and put it in the ademco system so i dont have to rewire the system? thanks in advance

I have a couple of questions if anyone can assist please before I order. I am using 3 x tritechs in house (a little ott but for pet tolerance) - I also have a conservatory that gets very hot but will not have pets. Should I just use another tritech or would a DT7450 be better? Has anyone used the Texecom Odyssey 5 compact or is it best to stick with full size? I have 3 x M12 smoke alarms on 1 zone and my installer doesnt have much experience of fitting these when using resistors. He was going to check but can anyone advise what may be required else we will just wire the whole system with seperate tamper circuit. thanks

Hi Is there a key fob option for the RKP. Thanks For your help Enjoy the weekend.

Dear sirs, I have an intruder alarm as above. It has two wired remote keypads. Is the Accenta rkp still available or is there a current alternative that will work with this system? Thank you,

Would this battery below be a suitable replacement for a Texecom 12V 2.4AH BATTERY for an accent 8 mini alarm system? Secware 12v 2.3a/h Battery [MKES3-12SA] - £8.09 : | Best Price Promise | Security Warehouse Professional products

I'm looking to buy an additional keypad for my current Accenta 8. The current RKP is the 8EP219 which is now obsolete. Does anyone know whether the 8EP416 will work with this. The Smartset will work using PTS but I'd like a Keypad. Looking at the 8EP416 it looks to only be compatible with the G3 and G4, as too does the new LCD keypad. Any help appreciated. Thanks

mMy keypad is faulty on my accenta 8 mini when i searched for the 8EP219 keypad i found it to be obsolete and replaced with the 8EP416. As i dont know what i'm doing can you tell me if its just a straight swap with the wireing?? Cheers MATT

CAN ANYONE TELL ME IF THE 8EP416 AND THE HWLEDKP IS COMPATIBLE WITH THE ACCENTA 8 MINI. ITS ABOUT 11 YEARS OLD

Hi i have the Accenta 8 mini. and the keypad is about dead. i am thinking of getting the keyfob. I got a few questions regarding it My keypad is situated on my stairs. and i am going to install the keyfob at the bottom of the stairs. or do the keyfobs have to be on the outside.. Could i connect the Easy set Key fob. whilst the alarm is still plugged in.. As i carnt remember how to set the alarm into diagnose mode so i can open the panel so the alarm dont go off. I installed it like 3 1/2 year ago and cant find the book for it.. any help will be great Thanks

Hi A friend of mine has bought a shop with a g3 alarm panel. Nobody knows the codes to use the alarm. I have tried various engineer codes but none work. Is there a way round this or is it a new main panel job. Thanks

Just installed the Accenta G4 panel and all worked well. a few days later a fault occured to the entry/exit. Problem is break to the pair of contact wire. Replace with the spare and makes and break but the problem is the panel does not register open/close of the contact but ok with the multimeter. Another factor that I can assume is new carpet was fitted and wonder if the fitter damaged the cable which I think would be most likely as it was all working fine before the carpet was fitted. No short between contact wire and tamper wire. Any help would be grateful. I will run a temp cable this weekend and see what happens.

Hello can anybody give me some advice on adjusting the volume on the above alarm system to low, altering the volume adjustment on the PCB has no effect the volume tone is quite loud, I had an accenta 8 system previously installed and had the same problem?. There is an intenal speaker fitted. Thanks