Intruder Alarms

Do the Honeywell sensors, external siren and tag reader with built-in siren communicate over encrypted rolling code? Do these - FG8M, DFS8M, CO8M, IR8M, IRPI8M, DO8M, SEF8M and SPR-S8EZ, etc. I know the fobs and panic buttons do. These do - TCC800M, TCPA1B, etc. I am using the Honeywell Evohome Security at the moment, that uses the Le Sucre+ box. Is the Le Sucre+ box and the SPR-S8EZ grade 2 EN50131, if they are not grade 2 EN50131 is the dominion a better control panel to use instead? I know the sensors, external siren, fobs and panic buttons are grade 2 EN50131.

Hi Experts I am looking for alarm system for my house having (preferably Free App mainly to disarm the system if its false alarm from Remote location) Area needs covering are sensors covering 1 Main Door Sensor 1 Sensor /Shock Sensor for Patio 4 Sensors covering (1 on Landing,1 sensor in Kitchens area,1 for living room ,1 sensor for garage) 1 or 2 Sounders off excellent build quality preferably with blinking LED. My preference is Wireless as house is new build (But can think of Sounder being Wired if its good to do so rest of all sensors being wireless) So far i have done some research and found Visoic PowerMaster 33 or 360R …

check outputs? can anyone help me make sure i set it up right and what to check/fix i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the extern…

Hello, I would like to buy an eaton i-wifi01 with a 12v bare wire power supply, do you supply the power supply as well?

Hi all I received my exchange from yourselves and today installed the new unit. The keypads now turns on unlike before. Just to recap i have connected to the system 3 x Pir`s and 1 door contact. 1 x 16ohm external speaker connected to the system 1 x Keypad connected to the system. 1 x Lan card connected. I turned the system on for the first time there were no sounds and the keypad behaved as expected. The Keypad states Euro 46 but not Euro 46 V10 like in the manual also the time and date adjusted itself, i assume this is because the Lan card is installed and had connection to the internet? More importantly i started to go through …

Hi all, purchased this from security warehouse last year and just got round to installing it. I have wired up all sensors - 3 Pir`s and 1 door contact. I have an 16ohm external speaker connected to the system I have 1 Keypad connected to the system. 1 have one Lan card connected. I turned it on for the first time and i hear a time which confirms it has been turned on. I expect the keypad to light up but there is nothing from the keypad. The keypad does not light up. I have read if i hold down the D key it allows you to select the address and there is no response from either the one supplied with the system or the flush keypad i purchase addition…

Hello I’m looking to purchase an alarm system with the following requirements: GSM Wireless Control box Capable of having two real external siren boxes Three wireless smoke alarms Three wireless PIR’s Two wireless door switches And also the capability of connecting at least two hard wired PIR devices Do you have any brands that would fulfill this requirement?

i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the external sounder immediately going off?any advice on how i can fix this please?

Hi there, I have just moved to a new house with an old Sterling 10 alarm system with 2 PIRs, it works but the keypad is very worn and I have no idea how to program it. I was thinking of getting the Euro mini keypad to replace just the keypad, see attached image with wiring. Will this work?

hey guys i have done a reset of my alarm system (had front door changed which affected tamper on door and i made the mistake of resetting entire system) so i am at step one and i am struggling to configure how it was before. i will try my best to give as much detail as possible. This is the setting at the moment. And i have put in red, the bits i am struggling with and trying to configure ZONE A/B (when leaving the home) (KITCHEN MOTION SENSOR) - MODE 06 INTRUDER (LOUNGE MOTION SENSOR ) - MODE 06 INTRUDER (BEDROOM MOTION SENSOR) - MODE 06 INTRUDER (UPSTAIRS LANDING) - MODE 6 INTRUDER FRONT D…

I have installed a Powermaster 33 along with a KP 250 Keypad. After months of no problems, the keypad display is now showing "No Communication" whenever any button is pressed. There is therefore no possibility of entering Installer Mode etc.. Is it likely that the communication failure is due to the keypad, the module inside the Powermaster control box or is it possible to reset the comms between the keypad and controller somehow? I would appreciate any help in resolving this matter. Thanks in advance.

i can't find anywhere in the settings for the display to stay on? i went to screen display and everything is selected YES after a while it times out until i press the keypad... can anyone help thanks

We have used lots of your V2 GSM auto diallers to good effect. One of our sales guys asked me about the possibilities of a unit that will send an email. Do any of your products be arranged to send emails.

I'm looking to update a wired system, new control unit and 6 PIR, (the existing door contacts and panics will be unchanged) any suggestions on most reliable and simplest models. It seems Texecom and Pyronix are the most reliable but which models and which PIR's for domestic use bells only with 2 Zones and approx 14 items on it??

Can anyone please advise? i have checked manual/interface its daunting i just need to know the basics please, everything is already in place - but .i changed my front door and the door sensor caused an issue/tamper and the alarm wouldnt set, and i made the mistake of resetting the device so i have lost all the devices from the memory thanks

please recomend an alternative wireless external sounder with longer battery life

Hi all, I have recently purchased a scantronic 9651 control panel from this site Iv'e also purchased honey-well pet friendly PIR's. I've managed to work out how to wire the bell-box and 9941 key pads but can some one help me with an idiots guide to wiring the PIR's and front door magnet. because I'm having trouble with the tamper wiring (do I need to use all 6 cables for the PIR and only 2 for the door magnet? Thanks in advance Darren

I have a Gardtec CP8L system that I inherited when I moved into my home several years ago. I wasn't left a code so asked the company who had serviced the system a couple of months previously to reset the system. On visiting, I was told that the system was faulty and the technician was unable to repair it. He left it powered-up such that the PIRs and bell box LEDs still flashed, so still acting as a deterrent. The keypad LCD display is blank. I have not touched the system, not even turning-off the mains, in case the external bell activates and I have no way of deactivating it. Is it possible that the anti-tamper mechanisms are still working? If so, how would I deactivat…

Hello, I have some question about the alarm system. We have two cats. Now I'm looking for the right alarm system for our house. I have 26 wired motion sensors and still need 4 wireless door and 7 wireless motion sensors. Which alarm is the better and the more modern, the Honeywell Galaxy Dimension GD-48 or the Galaxy Flex 50. Second question, I have the wired motion sensor “Active8 PIR with Pet Immunity”,( I bought them last year in England), are they compatible with Galaxy Dimension or Galaxy Flex. Or do I need other new wired motion sensors. The last question, what is the meaning of "Links" in the alarm system. Because the Honeywell Galaxy Dimension GD-48 have 64-Link…

just wondering if you stock a piece of hardware which allows you to separately connect cameras and PIR sensors they don't really have to be connected together but would like remote notification of PIR sensing so cameras can be looked at

Hi, I'm trying to put together a BOM / kit list of parts for an SPC4320 alarm. Need some help identifying compatible part numbers etc. Below is my first go at it. Would appreciate any tips. Cheers. Location Item Part Qty Utility Room Control Box 8-32zones SPC4320 1 Utility Room Backup Battery NP7.0-12 1 Utility Room 8 zone expander SPCE652.100 1 Utility Room 3G GSM receiver SPCN320 1 Hall Wired Keypad …

For our site we are going to need an expander for another building to be on the same system. Can a partition (area) have zones from the main panel and the expander?

How many keypads can I put on an I-on 50 if I am using 50 zones

1 x - Scantronic 9651EN-43 (9651 c/w 9943 rkp) 1 x - Secware Flex Tag Pack 10 1 x - Honeywell Reson8 Bell Box 1 x - Honeywell Reson8 Dummy Box 1 x - Secware KSB2 Sound Bomb 2, Quad Piezo Internal Sounder, 12VDC 7 x - Honeywell IS3012 PIR Motion Sensor with Pet-Immunity 2 x - SECWARE D20 Surface Contact 1 x - Scantronic 9941 LCD Keypad Im looking to purchase the above items, I have cable. will all this work together also the tags on both keypads?

we bought a galaxy 2-12 C012 some time ago and when we are trying to enter with the engineer code it is saying invalid code is there a way how to factory reset so the codes will be all reset please? it is a galaxy 2-12 honeywell intruder alarm panel