Intruder Alarms

Hi I need to check a couple of things... 1. If I order the "Castle Care-Tech Euro One (includes LCD keypad)" from your site - part number EUR-1024... it says you get the panel and the remote keypad - is the keypad fitted with the Prox sensor for proximity fobs? 2. If it is how many fobs come with the panel? 3. We have never fitted this panel and have tried to get the engineer/installation manual from the Castle Care Tech website and it is password protected... we have registered with them but heard nothing yet - does the panel ship with installation/setup details? 4. do you have to use the Castle Care-Tech proximity fobs, or can you programme the cheaper ADE Ho…

I want to use 12volt bells as my warning devices but I've been told that they will burn out the microprocessors on modern control panels. Is this just a way for the trade installer to put me off doing it myself or is there any truth in what he's saying.

hi... should be recieving my alarm from you trammorow and want to take a go at installing it my self.... but looking at the wires my sons layed 8 core instead of six :-\... and than for the internal speaker they did not feed the wire to the control panel instead the fed it to the keypad :-\. what can i do can i use the 8 core wire? and what about the internal speaker... and plus they layed the 8core for everything which is the bell box... PIR,s . Thanks guys by the way the alarm i purchased is ADE Honeywell Accenta Mini Gen4 with LCD Keypad hope that helps thanks!

Hi i have a Galaxy 2-20 control panel, i don't know the engineering code , can any one help me how to factory reset the panel? thanks

Hi, Having problems programming Honeywell Domonial wireless 2 PIR kit Thanks

Is the 9448 manual the same or similar to the 9448+ manual as I need to gain access to the panel without it going into full alarm. Or can anyone tell me how this can be done. I have installed many Optimas over the years but never got involved with Scantronic.

I HAVE A RISCO ALARM FITTED WHICH CAN BE ACTIVATED REMOTELY, I AM GOING TO BUY THE RISCO 4 BUTTON REMOTE FOBS, DOES ANYONE KNOW IF THEY COME WITH PROGRAMMING INSTRUCTIONS ? OR IF NOT DOES ANYONE KNOW HOW TO PROGRAMME THEM TO MY SYSTEM ? THANKS

Hi I have a Guardtech D500 system installed in my home an it incorporates shockguard sensors etc. I have just had new double glazing fitted and some of the sensors have been damaged, I would therefore like to upgrade my system with a new one as the wiring is already in place for the sensors I would like a wired and wireless system to increase security, I have been looking at the 595 or 816 and have spected out as system below can anyone tell me if this would work and if i have missed anything out? Guredtec 595 or (816 which has 16 zones, can I use each zone for each shockguard window sensor is this correct) 2 x wired surface mount magnetic door s…

Do you sell them? Regards.

Hi informa bought with accenta poly gen4 (LCD Keypad) on 23 March. Alarm installed ok. Informa wired as per instructions. Programmed phone number and recorded message. When testing, you can hear number being dialled on the infoma box and then shortly after you hear the recorded message but the programmed telephone does not ring. Tried it with different numbers and programmed the number on 1,2&3. When trying it with a mobile phone number, the mobile didn\'t ring but received a missed call from the unit about 5 minutes later (this didn\'t happen everytime we tried the mobile - nothing came through). thanks

Was wondering if anybody has detail for the Scantronic Plug-in footprint used by the 960? I wanted to hook this speech dialer up to an alarm that does not have the Scantronic footprint. If I could get hold of the spec for the two connectors of the 960 I could then jury rig a connector (or spade terminals) to tease out the 4 standard triggers as well as the line fail signal. I could also take care of any other inputs that need to be dealt with. Any ideas? I've done an extensive web search for detail of the footprint but have not found anything. Thanks John

Hi, I hope somebody can shed a light on this fault I have on the Texecom Excel panel. Installed this on Saturday but Zone 6 keeps triggering after being armed after a few minutes. Checked the Pir and that seems OK. So removed the Pir in circuit and strapped a 10K resister in Z6 but still activates after a few minutes. Is there a simple solution to this or a faulty panel. All other zones are working good. Using EOL method. Thanks in advance.

Do you sell both MCT-302 and MCT-302T? The information in the text on the site talks about both items but in the end it is indicated that you only sell MCT-302. Is this correct?

Hi i have installed all the system , when i test the system for dialling a tel. no. it works , but when i make a test alarm activation , the speech dialler does not dial any numbers saved in it . please advise? Mahdi

Hi. After installing a new accenta mini today i was ready to power up. connected mains but on connecting battery connections i saw the battery fuse blow. I checked all wiring, found to be correct and changed the fuse, connected battery and again the fuse blew immediately. I then disconnected all wiring from the system, i.e. bells and detectors, so it was 'as arrived new' and again, replaced battery fuse, powered mains and connected battery and the same thing happened again. I left battery & fuse out and powered up from mains. Alarm seemed to be working ok but i then noticed smoke coming from a resistor above and slightly right to the battery fuse, so i…

On which frequency does the Visonic PowerMax+ system that SecurityWarehouse sell use? /DG

Hi. I am interested in a Powermax alarm system, but need some information and advice. First, I live in Sweden, shipping available? And if so, could you please state the total price delivered to me? Our needs are for a two-storage residential home at a total of 145 square meters There are two main entraces and two patio doors in glass. The two patio doors are in immediate proximity to large window portions with windows from one side of the room to the other at a total of two times 5 meters and reaching from floor to roof. There are also a bathroom window and two windows at the entrance from floor to roof. We want to have the possibility to arm the alarm for

Hello, We recently moved into a house that has a non functional wired ITEC Meridian panel (prob. 20 years old?). It has power to it but the front keypad does not respond to any key presses, and the alarm it not activated by the tamper switches on the panel door. The last occupiers never used it (over 12 years or so) and did not have any codes or manuals so I was thinking that the easiest solution would be to fit a new panel. I've no experience with alarms but I am an electronics engineer so am happy to give it a try with some helpful advice:) Present zone layout: Z1: PIR on stairs (6 core cable) Z2: Garage door magnetic reed switch (6 core cable) Z3: 5 of GS610…

Hi, I am looking at the above kit to add 1 wireless door contact and 1/2 wireless PIR's to my existing wired system. Does anyone know how the unit is powered ? I think it's 12v but is this via a plug in transformer or does this somehow get it's power from an existing panel ? Also what frequency is this, is it 433 or 866 Mhz. Thanks George

i'm sorry but yesterday i received your ex-35r optex detectors and, comparing with mine, i discovered that inside my detector there is one more transmitter, probably compatible with my General Electric "Simon" alarm. here you can see the manual (in italian) of my "Simon": http://www.hesa.com/index.php?page=shop.getfile&file_id=658&product_id=515&option=com_virtuemart&Itemid=37 in this manual it is written that Simon works with any "autolearning" detector SX ITI at 433Mhz. if you want, i would like to send you a picture to show the transmitter that is inside, and if you have it i can purchase, or if you have detectors compatible with my alarm system …

Hi I would like to add a couple of remote keyfobs (KTC805) to my existing Dominial installation. Is this the same process as adding a new user / proximity tag or is there a different process? Do installation instructions come with the keyfobs? Thanks Mark

I would like to install either a Honeywell Galaxy 2-20 or 2-44. The house is very large with detached garages 10m away. Because the majority of the house floors can not be lifted and the decoration disturbed a wireless system must be fitted. This does not seem to be a problem for the Galaxy G2. Initial assessment suggest that in excess of 40 wireless detectors are required (dual-tec, door contacts, smoke alarms etc). As far as I can tell from the Honeywell specs there is no limit to the number of wireless detectors that can be added to the system, is this correct? Without doing a detailed RF site survey I anticipate that 2 RF portals will be required, the …

Is CQR cable worth the extra over ordinary alarm cable?

hello i am looking for a alarm system which will protect my home and garage .also a cctv system with hard drive.thks adam

please i am wanting to buy the scantronic 55 system however i have some questions - does this have a phone out feature via sim card or by bt line if it is triggered. does this accept pir / door contacts that have been used for an optima honeywell hard wired system since it is an 'hybrid' system... so that i might replace the optima and buy the wireless pir as and when i can. essentially i need a wireless system for a domestic use where i would have around 5 pir and couple of door contacts and smoke alarm external bell and key fob - is there anything other than the homelink 55 that is also suitable and fairly straightforward to use - set up and around