Intruder Alarms

Please would you clarify if the "Honeywell Intellisense 800L 8 Zone LED Control Panel Honeywell Intellisense 800L 8 Zone LED Control Panel" at

I'm wanting to buy a Bosch ISM-BLD1-P burglar alarm sensor, to replace a non-pet friendly sensor that is currently installed- it is a pain to keep pets out of that particular room. (The rest of the house is covered by existing ISM-BLD1-P's). The webpage mentions that there are different microwave frequencies that the detector can operate at, with each different frequency variant having a different letter at the end of the product code (F1, F3 or F4). Are you able to advise which frequency I am likely to require- are these different units? I can't find any mention of microwave frequency in any of the documentation for my current system.

Hi, Just trying to put together a quote for a high end residential property, we are upgrading the video intercom, cctv amd intruder alarm...in the past have used powermax for small residential wireless and galaxy for commercial, client likes fancy toys, is there any intruder and cctv that can be integrated or an intruder system that has an app for a smart phone but the system must be wireless. Basically they want a fleshly system he can show off

The Scantronic Sounder External Wired Backplate, SDR-WEXT-G2, installed a few years ago worked perfectly until about a week ago, when I noticed that the 'comfort LEDs' had stopped working. On further investigation the unt does not sound the siren when an alarm condition is triggered, although the internal Scantronic 9651PD does. On opening the external sounder box its cover tamper switch does not trigger the external siren but again it does trigger the 9651PD. On further investigation, the internal battery of the external sounder is fully charged, therefore I suspect the sounder circuit board is faulty. Are replacement circuit boards available for this unit as I don't…

I am looking at the few control panels and have a few queries which I hope you can assist with. Install is for detached 5 bed house. Suggestions are: - Texecom Veritas R8 Plus - Scantronic 9651EN - Pyronix Sterling 10 1. Believe all are grade 2 but not entirely clear. Is this correct? 2. All seem to be 8 zone but with the Sterling it has an additional dedicated PA zone. I am correct that on the others would need to allocate 1 of 8 zones for PA? 3. Last install a few years back was a Pyronix Paragon which we had no problems with. Is the new Sterling of similar quality to the Scantronic and Texecom which seem to be a lot more popular? 4. Assume all ha…

Hello, My alarm panel has packed up so I'm replacing it. The bellbox has seen better days so replacing that as well. My original was a Scantronic 9448 so am going for the 9448EUR-90 control panel but can't decide which bellbox to go for. I'm stuck between Novagard 2 Merit , Ventcroft Compact Classic & Ventcroft Evolution. I want to know are they all compatable with my alarm system and which are reccomended? Thanks

I am considering purchasing some sensors and require the red flashing light to be activated as a visual deterant when the alarm is ON and also when it is OFF. I am currently looking at the Viper GL-W thats says the LED is activated by LINK and the GLX-W that says is activated by SWITCH. Can you please explain what the difference is between LINK and SWITCH. Also, The GLX-W PC.09000-20 is priced at

Can 1 dialler be used between 2 alarm systems that are within 100m of each other?

Hi, I'm about to install a Honneywell Accenta G4 c/w remote keypad need some advice on.... Bell box; thinking on getting Ag6 or AG8 or Reson8 PIR; Bosch Blue Line Gen2 pet friendly Battery; looking at the secware 12v 2.2a/h but instructions say a max of 2.1a, will this be ok ? Fire Detector; need two of these, what would be best ? Thanks

Hi, Just trying to put together a quote for a high end residential property, we are upgrading the video intercom, cctv amd intruder alarm...in the past have used powermax for small residential wireless and galaxy for commercial, client likes fancy toys, is there any intruder and cctv that can be integrated or an intruder system that has an app for a smart phone but the system must be wireless. Basically they want a fleshly system he can show off

Hello, Can we assign different sirens (I want 2 sirens) depending on the zones or suites on Texecom Premier elite 44 or more.

Having just commissioned a 9651 I've been testing out event logging for the system. I isolated the mains supply, hopping to invoke a mains fail alert. The RKP recorded the event properly, but interrogation of the event log showed no mains fail alerts. I carried out this mains fail test for both set and unset modes with the same result. Do I have to enable logging for this type of event somehow, or should it be enabled automatically? Or perhaps there's a timer on mains fail events and I didn't leave the mains off long enough? Any ideas? thanks John

Dear Sir / Madam. I am looking at replacing my aged Yale SA5 alarm system with a product from your company and i was looking at the Scantronic i-on40 with wired kp's for a solution. Does the system allow Remote turn off via a PSTN network or over the public internet via a login.If not could you suggest a more appropriate solution. Thank you for your time. Regards Paul

Having searched numerous forum posts I'm at a total loss, so I thought I'd try asking... I have a Honeywell Optima Alarm system (8EP396A panel with a 8EP417A LCD Keypad and a single PIR sensor) for my shed. When I entered this morning and entered the code the alarm sounded but every time I entered the correct code the alarm would briefly stop and then sound again. the only way I found to stop it is power it down and remove the battery. I only have about a second to see the fault, which is coming up as a PA fault. but the PA connection on the panel has a link cable closing the system (I assume this means it's not in use?) I've tried doing a reset of the syste…

I currently have a visonic powermaster 33 installed and working nicely. I have the gsm module, which is connected to a central monitoring server thing run by a third party. I'm looking at buying the powerlink 3, will this enable me to connect into the alarm myself so that I don't need to use a central monitoring station? I know that the powerlink 2 allowed you to do this, but not sure about the powerlink3. I have the Powermaster 33 PG2, and I've confirmed that it's got firmware 18. So, before I buy it please can you 100% confirm that if I buy the Powerlink3, I'll be able to connect into it WITHOUT needing to pay for a powermanage server? Ie I'd connect directly t…

The 6 stand-by batteries in the main panel are not being trickle charged. Replacing them with fully charged new ones (1.37V) gets the system working correctly in all respects but only for approx 3 hours. The cells are then down to 1.2V off-load. Have you any information regarding the charging circuit that could allow me to investigate further and possibly repair? Your website indicates that the Homelink 75 is “sold out”. If I need to purchase a replacement system can you please recommend a suitable model Having had further time to think, it would seem logical to assume that the panel’s internal power supply is not producing anything at all - not just the battery charg…

Hi, I would be most grateful if someone could answer the following question regarding this panel as I can't seem to get hold of the installation manual for it. 1. Product description for the Euro Mini says that this panel has 10 EoL zones. Does that mean that it is FSL capable? 2. If so what are the resistor values? 3. I'm assuming that I would require a 12v 7AH backup battery for this panel. Would that be correct? Thanks in advance.

Just bought a Powermax+ with some sensors and a GSM module. I wonder if I can connect both the control panel and the GSM module to the same powersupply, thus reducing the number of wires needed. One possible solution would be to connect the power to the control panel, and then another wire from the control panel (2 wires at the same connectionpoint) to the GSM module. Another way would be to use some sort of "Y" connection to route power to both consumers.

Hello all, appreciate some help here, i have 4 pir sensors and a ADE Accenta Mini Gen4 panel, how should i wire the pir sensors in series? or should i wire each pir back to the panel? thanks for the advise!

Hi, how is this alarm armed and disarmed? Does the alarm come with all of the parts to mount it to a wall? How loud is the alarm? We have an external light which sometimes comes on at night if our neighbour walks into his garden, would this light coming on at night time trigger the alarm? i look forward to hearing from you.

Hi I am installing a accenta Gen 4 system .Its for a residential home for people with learning difficulties. Basiacllly they want the doors to chime and light up on the key pad until reset or another door opens . So the light is on pretty much all the time regardless of the door then being shut I am thinking of installing your "Elmdene EN3 QFC Grade 3 flush contacts red resistor " I just want to know whether these are compatible with the system . Ie I am not going to install them then a fault comes up on the keypad

I am planning to import a comprehensive Visonic Power G2 System with many detectors into Germany. I understand that all components of the system have to be UK components in order to be compatible. Before ordering I need answers to the followings questions: Can the language of the Power Master 30 panel be changed from English to German? Will the Power Master 30 panel with the GSM-350 PG2 and the Powerlink 3 modules be able to communicate with Visonic’s PowerManage IP/GPRS-based Security Management Platform installed at a German central monitoring station? Will the alarm data and other data transmitted by the Power Master 30 panel to the CMS also be in German? Would I hav…

Normally fit ADE Honeywell control panel with LCD remote keypad. New Customer Installation. Customer wants to be able to set alarm with a proximity key. What would you recommend.

Good morning, we are just finalising our new warehouse and need a beam system that can be put across the main shutter door that will play an audible alert if anyone enters the warehouse. Could you please advise what equipment we would require

Dear sir,s i am having trouble setting my alarm key pad .power light on ,green light on ,when i programe 0123 zones 4.7.8 led lights come on and the key pad box makes a ddrrrrr ! sound any advise much welcomed yours sincerly Fred Parkinson my ref 8611.or 8710.