Intruder Alarms

I require a standalone wireless receiver plus 2 IR room sensor to connect to an ADC type panel (wire to existing sensors has been cut by flooring contractor)... The Nova 2 would appear to fit the bill?

I am building a new house and a granny flat The alarm will consist of wired system and external bell box aswell internal bell box. Alarm pack with keypad and fob for the house. - 2 keypad and fob (one for upstairs and downstairs) - 4 pir sensors (pet friendly) - two door sensors (front door and back door) - one 7m rear sliding door (door sensor?) However I have a detached garage which have a granny flat above which I aim to rent out. The garage which will be linked with house alarm system. 1 x pir sensor 1 x door sensor 1 x roller door sensor But I would like the granny flat to have its own zone linked with house alarm. (If that is possible) when my tenant is in flat…

All has been fine then about a month ago while setting it l received the message open zone 5 l don't know what have caused this. Have you any ideas? That zone is on a PIR Its a Honeywell lS3012.If you think l need to purchase a new PIR let me know or could it just need re programming?

Hi, I'm an installer looking for a 6 zone wired panel with option to expand using app, What do you suggest?

Hi, I've just installed a Scantronic Homelink55 and the hardwired side of this has worked perfectly straight away. However the wireless side has proved more problematic ? I am tring to 'link' the RFX16 unit with 2 x 703r transmitters, I can get the reciever into learn mode, either -- flashing for the sysetm to allocate the channel or, for instance with 09 flashing (I have configured it to addres from zone 09 onwards). I have the 703r set to have the Ln set to E -enabled; however, with 12v connected the green nlight is on but unless I change the oP there is no activity from the RED LED!! I've tried marrying the both 703rs and have tried both connected to the panel bus …

Hi, I am looking at the above kit to add 1 wireless door contact and 1/2 wireless PIR's to my existing wired system. Does anyone know how the unit is powered ? I think it's 12v but is this via a plug in transformer or does this somehow get it's power from an existing panel ? Also what frequency is this, is it 433 or 866 Mhz. Thanks George

I wish to order the following, can you help me ? 1x Texecom R8 plus + battery 3x Keypad (normal, no lcd) 1x indepedent Bell for inside + battery 1x indepedent Bell for outside + battery 2x Heat detector + shipping to France Thank you, very much (No need of PT wise i have already in stock ) Well, So i have 2 questions : i don't find any bell that are independant with battery, can you tell me a reference for one outside and inside ? For heat sensor, do i need RELAY version or not ?

Is the Secware 12v 2.2A/h Value Alarm Battery (product number 70/118) suitable for the above control panel? Is it normal for this battery to require replacing after 5 years?

Can you provide visonic power master magnets to compliment the visonic shock/vibration sensor making it a shock/contact sensor?

I have the above alarm unit & have been told that I need new PIR detectors. please can you give me a quote as to how much the PIR's are for the above unit.. PIR type 433. thanks

I am assembling the individual components of the Optima 4 kit minus the SAB strobe. I am substituting the Odyssey 3E, as I already have the diamond shaped cover. I have found all the components but not an exact match for 2.1Ah battery and surface door contact - could you advise which battery model and which surface contact model I should order?

i am having a problem with a gardtec 370 panel ,when i come out of engineers mode,i have an internal sounder, and the figure 66 shows on the key pad display,can anyone please tell me what this is.

I am looking at purchasing a home alarm system for my house. My friends here in Sweden recommend the Visonic line. I am looking at a package to include the following: PowerMaster-33 G2 or PowerMaster-10 G2, could you please help me with what the pros and cons would be between these two? 1 x Internal GSM-modul GSM-350V21 2 x Wireless cameras (NEXT CAM PG2) 3 x Wireless magnets (MC-302 PG2) 2 x Wireless smoke detectors (SMD-426 PG2) Touch-panel + 3 tags either KPA-160 N PG2 or KP-250 PG2, could you please help me with what the pros and cons would be between these two? 1 x remote control Might also be interested in one or two outdoor cameras or motion detectors with lights

Hey all, I recently moved out of a house that had a Galaxy G2 system. I have recently bought a Flex 20 for the new house we've just moved to, and everything is now working as expected apart from one thing I can't get my head around. On the old system, we had a Wireless Magnetic Sensor on the front door. This was set up so that when we Full Set the system, that Function was a FINAL zone. If we Night Set (or Part Set), the function was INTRUDER. This meant if the door was opened whilst in Night Set mode, an immediate alarm was triggered. If it was opened during full set, the entry time was triggered. To set this up, we could go into Engineer mode, into the Zone, in…

Hi. I'm trying to find a light beam sensor to work on a driveway, to send a signal to my house when a vehicle or person breaks the beam. Can be hard-wired or wireless - the location is about 120m from the house - the back entrance to a farm. I think you must do such devices but I can't see them online.

I am currently installing an alarm/fire system in my home and have a few questions someone may kindly answer: 1. Does the Eurosec CPX have a built in dialer to call in the event of an alarm (so all I do is add a bt line) and if so does it tell you what the alarm is i.e zone, fire, intruder etc. 2. What type of cable should I use for the smoke heat detecors - normal alarm cable? 3. What smoke heat detecors are compatable with the Eurosec CPX? 4. The alarm unit will be mounted in a seperate room only accesable from outside (it's a outside utility room) although the utility room is secure would it be better to have the main unit within the house? 5. Finally, can you …

Hello, I have a Scantronic system consisting of a 9448 end station and 9427 RKP. I wish to add a further RKP and the only RKP apparently available is 9427EUR-80. Is this suitable?

Hi, just bought one of these, does anyone know the default Username and Password to enable me to gain access to the panel via its web interface? Ta.

Do you have a wall mounted Pir covering more than 120 degrees? Like GE's Sharpshooter

Hi all, I hope this generates some discussion and hopefully for me an informed conslusion which will send me down the right path to purchase. I am looking at installing my first wireless alarm system (I have installed a few wired systems in the past but that was a long time ago) so technology has improved somewhat however I have some specific requirements which I am hoping some expert guidance will help me choose an appropriate system. The property is a new build with 3 levels, there is a garage within the build however there is no access from inside the house (only garage door access), gates to each side of the property and the rear of the property has a 30 ft …

We have Optex FX-59 QZ alarm system which now it says to replace batteries however there are no batteries inside the sensors and in the panel. What are we supposed to do in this case? The alarm went off and an orange light keeps flashing.

Have Gardtec 350 panel which requires a closed tamper circuit. Can you please suggest a suitable relay to use with the mcr-304 to give a NC output.

Hello, I have just finished some work to tidy up the wiring on the Accenta Gen4 system fitted in my flat. Basically what I did was re-route a lot of the surface cabling under the floor, and also change a couple of the sensors. Now the system is up and running again it all seems to work fine, apart from the door contact. The door used to have a surface mounted Honeywell contact, and one of the changes I made was to swap that for a flush contact hidden in the doorframe (part is CQR FC508/WH). When I test the output from contact back at the panel with a multimeter is it fine; reads 2 Ohms with the door closed and then open circuit with the door opened. However…

Hope someone can give some help or suggestions. After being broken into earlier in the year, I have finally got round to installing the alarm system that was purchased a couple of months ago. Every thing seems to work, that is after a minor wiring fault on the global system tamper, which turned out to be poor connection on vibration sensor (front door). The problem is the external sounder will not function at all, apart from the tamper circuit. There is definitely power from the control panel and the standby battery has 8 volts. I have tried the trouble shooting instructions in the installation manual, which is make temp connection between SAB B and D for the sound…

hello, could you tell me what frequency your texecom intelligent keyfobs are? I have an 868mhz intelligent receiver and i want to make sure they match. thankyou sanj