Intruder Alarms

Hi guys, I’m curently using a couple of Texecom RF 360 PIR sensors (from your good selves). I’ve had them in place for several years covering some common hall/landing areas, all good. Last year I got a cat… Even on pulse count=2 these sensors are not pet immune, and as a result I’ve had to stop arming the alarm, otherwise the cat will set off false alarms all the time. ? I need to stick with 360 ceiling mounted sensors as the wiring is in place inside a finished ceiling. I have a little void, so I could potentially change from surface to recessed flush mounting if necessary… Is there such a thing as a pet immune 360 ceiling PIR? would perh…

Hi I need to purchase a wireless alarm system with proximity entry I have looked at the powermaster visonic range but need to know if the powermaster 10 panel has an internal 12 v supply outlet so I can add my already owned gsm dialer.I have seen that there are two proximity readers in the powermaster range the kp 160 and the kp 141 which is the most suitable and easiset to use and are the proximity tags an extra with these items

Hi all, I have recently purchased a scantronic 9651 control panel from this site Iv'e also purchased honey-well pet friendly PIR's. I've managed to work out how to wire the bell-box and 9941 key pads but can some one help me with an idiots guide to wiring the PIR's and front door magnet. because I'm having trouble with the tamper wiring (do I need to use all 6 cables for the PIR and only 2 for the door magnet? Thanks in advance Darren

CAN ANYONE TELL ME IF THE 8EP416 AND THE HWLEDKP IS COMPATIBLE WITH THE ACCENTA 8 MINI. ITS ABOUT 11 YEARS OLD

Hello I have a veritas control panel and key pad with a wired intruder alarm system. The power circuit tripped and now I have the \"unlock\" light flashing. Until this is sorted I cannot set my alarm. Can you help please. Regards Roger Bell

I ordered a Visonic PowerLink2 (9-101070) hoping it would be compatible with my power master 30 but it doesn't seem to be. Can it be? If not which one is to connect my master 30 to the Lan?

Really need some help before I loose all my hair. Trying to set up premier 24 with 4XP expander. No matter which setting I use for the Address switch I can't get the expander to register as installed, just as 1 or 2 extra keypads. Any Ideas? Thanks in advance

I am after a remote that will work on a Sterling 10 for setting/unsetting? Is this possible?

I am fitting a new intruder alarm system to my house, and want to utilise the wired sensors, etc I already have. However I want to have remote control operation as well. To achieve this I am looking at the Galaxy G2-12 panel with wireless expander (RF Portal) and wireless remote controls. Is the wireless module compatible wiht the G2-12 or do I have to move up to the G2-20?

Can anyone recommend a simple wired alarm system with support for maybe 2 door contacts, and 4-6 PIR's. I'd like one with GSM support to SMS me when an alarm event is triggered. Any other fancy features like internet monitoring would be nice, but not necessary. This will be for domestic use - and only used very occasionally i.e. - when on holiday. No pets in the house. Thanks,

Hello, I have now received my alarm but when I connect power I get a fault code: - NOT READY TRBL MEMORY and I can not find this fault code in the maual or on Visonics webpage. Please advise how to proceed.

I ordered the above Visonic MCR-304 Receiver from you and it was quickly delivered without any sign of transit damage. Firstly my thanks for your prompt service. I installed the item in the prescribed way and powered it up. I then set the Learn jumper into the Learn mode and the yellow LED flashed as expected. I then pressed the Tamper spring and the yellow LED and the red LED both flashed OK and using the tamper key I was able to cycle through the various channels. I then tried to associate/enroll a known good transmitter and in this respect I used a MCT-100. This transmitter was free standing and located close to the MCR-304 so range was not an issue. I tried to force …

Item Scantronic 9651UK with 9941 keypad. I installed this control unit to replace another 9651 unit which had developed a fault. After installation I tried to exit the 'Installer Mode' and the unit reported 'Zone Flt' on zones Z01 through Z08 and the Service LED is permanently illuminated. I have checked power to the Ziper intruder detectors and circuit continuity for the FSLs and they seem to be OK. I did notice that the 9651 unit had a manufacturer's date of Jan 05, so it seems to have been in storage for some considerable time but that aside I would appreciate some assistance in identifying where the problem lies and if it is a defective unit, getting it swapped out.…

My problem is an Optima Compact giving spurious tamper alarms on the control panel. These are totally random and alerting the internal sounder not the outside alarm box when in day mode. The strobe flashes when this event occurs but as I say no alarm. When the system is set the alarm box works normally. On a suggestion I have changed the alarm panel battery . Spurious alarms from the panel seemed cured for 10 days but now have returned . Any possible answer to the issue appreciated.

I purchased an alarm system last year, and until today has worked without fault, however, when my Wife tried to set our alarm in the usual way using the ADE Simple Set she was unable to do so. When I came home I also tried without success. The unit shows both Power & Day lights but when either a 'learnt' or an 'unlearnt' fob is offered to the unit there is no response regardless of the length of time the fob is held against the unit. Any advice would be greatly appreciated. The unit is less than 12 months old

Hi can you help, I have a client with a alarm system, th only information we can find is its a , RS 125, I seem to remember that jSB made some of these alarms, its about 16 years old, we need a new RKP for it, 7702-1762 VERSION 1-5 if you follow this link it brings up the manual /mcalarms.co.uk/manuals/eb2160715c71a5288868dea766782281_RS125UserManual.pdf can you tell ne if its availble and cost

Hi, I recently purchased a new CPX alarm. I have programmed the alarm with multiple sensors and was attempting to test the set when I got the following message: please enter eng + anticode 4141 Can anyone help? Thanks, Darrin

I have a cooper security 9651 panel. I'm rewiring the panel from global tamper to FSL because i've been told its more secure. I've wired single PIR zones with no trouble but when there is more than one PIR or surface contact or Panic button it shows tamper in walk test. If I one device is open at once in a zone, its fine but if I open two or more devices in one zone, the panel detects tamper. (E.g. When I open one door in Zone 7, the panel doesn't say tamper but when I open a door and a window in Zone 7 the panel will detect tamper) Can someone help me with this problem? Thanks Krishan

is there a wireless trasmitter/reciver interface that can be fitted to the above to expand the system to more than 8 zones

I want to buy the new Honeywell Galaxy Flex - are you able to supply it in a package like you have done for the "Honeywell Galaxy Dimension

Hello. Do you have an Intellisense IQ260 replacement/equivalent please. I have one in my garage, after doing some refurbishment to the building I was thinking of installing an additional sensor as a single one can no longer cover the area. That is if 2 pir's be installed in the same zone/room? an 8 core cable is installed however only 1 core remains unused. If 2 can be used on same cable maybe better to buy two identical detectors and do away with the IQ260? Thank you.

RISCO Group have a product update A new firmware update has been introduced to the Wisdom wireless control panel. The new version of the Wisdom firmware is V4.31, updated from V4.27 Why have we upgraded the WisDom panel The following fixes/updates have been modified to bring you an improved panel. Technical The panel has a new menu to show the connected BUS AGM IMEI number (Used for IP Receiver) The Blank Display has been updated in that you now only need to enter your code once. The

I'm looking to spec up and purchase an alarm system for my house. I need a panel with 20 WIRED inputs, 2 keypads, and an extrenal sounder. I'm looking at the Honeywell galaxy flex system with the KO7 KP and ethernet interface, so we can use the Galaxy app to moniter. Please could you advise which products I will need for this package, and if you will despatch to my address in Greece. Thank in advance.

I'm tring to programme the bell time on this panel in engineering mode. When I press "6", LED's 1,2 and 3 should show but I'm getting 1,3,5 and 7 and then it won't go any further. Does anyone know what this means and why it is happening?

I installed 3 years ago a Scantronic 9651 Hardwired Control Unit. I wish to install 3 new PIR detectors and would enquire which of your products is most suitable. I note Scantronic do a pet tolerant PIR ref 430. Is this compatable with the standard 6 wire system?