Intruder Alarms

We recently purchased a system which includes 2 x Pyronix Deltabell and a honeywell ADE GEN4 metal system. When reading the Pyronix data sheet it states that the bell trigger to the Deltabell must not be in paralled ( ie from one output ) two outputs must be used. The problem is I dont think the GEN 4 panel has a second bell output terminal, or have i missed it? As the deltabell is class 3 we have to install a resistor (4k7) from the +ve to the bell trigger ( to give it aprox 2v or above during normal mode ). With one deltabell this works fine. How should I connect the other deltabell? would a solution be to install a 2K resistor in place of the 4K7 and set both bells t…

I wonder if you can help. I have a Galaxy G2-20 and 8 ACTIV8 PIR hard wired sensors. The sensors have 8 terminals inside EOL TAM TAM RLY RLY EOL +12 -12 How do I connect these to the Galaxy? Should I choose normal closed or double balanced which is the default? What is the difference between these two modes? James

Deleted

I Think that I require, Control panel (can be hidden under stairs) 1-off Nice looking Lcd keypad (for front door) 1-off keypad (for rear door) 3-off wired Quad PIR for inside 2-off wired Dual tech PIR for outhouse (extreme cold/heat). 3-off internal Door contacts. 1-off garage Door contacts. Panic Button Txt or voice dialler Listen in function Dial in to arm/disarm would be nice or over web via phone? It would be good if the alarm had wired and wireless zones in case I need to upgrade after the floors went down I really like the Honeywell Galaxy Dimension GD-48C with Touchsceen Keypad Kit, but is it over kill? What would you get? Thanks in advance…

I have a Honeywell Acenta G4panel with 2keypads that need replacement. I know this panel is obsolete but it is in good condition overall. What alternative led keypads would work with this panel?

upon power uo of my recently purchased optima gen4 copact alarm the alarm sounds- enter code 0123 and the alarm siren silences. i have no flashing tamper light despite the cover being off,i have a flashing sos led which will not go out whatever i press? i have the global tamper pa & ta terminals shorted out but still am unable to extinguish the sos led. do you think the unit is faulty or am i missing something obvious

Accenta G4 mini from you. Connected it up and fully tested including under alarm conditions. Last week I had an alarm activation which worked fine BUT the strobe will not reset. Thinking I had a faulty siren I bought a Honeywell ActiveGuard AG3 from you. I powered down the panel and connected the new siren. Repowered and the strobe was immediately flashing and still won't reset! Powered down the panel and connected the siren with a short length of new cable. Repowered the panel and the strobe was immediately flashing and still won't reset.

The Risco Wisdom comes in two versions. A plain LCD driven panel and an LCD & Voice driven panel, giving set, unset and alarm voice prompts. All three kit pages mention: 'Two Model: LCDversion and LCD version with voice prompts' As it doesnt specifically say on your kits im wondering which version you sell?

Hi, I purchased the Wintex software off your website last night. However I am unable to download the software, it just says "NOTE: Downloads are not available until payment has been confirmed" My order number is #12973. Would it be possible to email me the .zip file please? Thanks, Tom.

I am ready to order the subject item, model 18.980049 but need to know the following, Does the product come with the relevent sounder switch, i am wanting to run this unit for staff tea breaks so just wish to run siren to a switch then onto the 240v mains ! Can you confirm this is possible & also if the product does not come with a switch can you give me the part number so i can order at the same time. Could you also tell me how long it will take to arrive.

I am struggling to find information on how to wire the Pyronix Deltabell Plus to the Honeywell Flex 20. Also i would like to know how to wire the Honeywell DT8012F5 DUAL TEC Motion Sensor with Pet-Immunity (DT8012F5) to the Honeywell Flex 20 panel. At present i have connected the positive and negative to +12V and 0V. I have connected the NC to 0V and put a 1K resistor at the sensor to C, and then again a 1K resistor from C to Tamper. The problem i have is the sensor doesn't have a Fault terminal to wire to zone 1.

Hi, Thanks to this forum I've picked up some usefull ideas for my future home alarm. I was wondering if someone with a little more experience could tell me if the following things work great together?: 1x Texecom Premier 48 7x Texecom Prestige AMDT Plus pir 14x Elmdeme EN3-QSC Grade3 medium surface contact with red resistors 5x CQR 8 core screened 100m 1x Texecom Odyssey 5 dummy 1x Texecom Odyssey 5 cover 2x Texecom Premier Large LCD keypad 1x Secware RS002/ALI 2x Secware 2way sound bomb 8x Elmdene EN3 10way junction box 1x Enersys 12V 18A/H batt 1x Secware Bcintra/w/b Also If I wanted to connect lets say 3 smoke detectors? Do I just connect them…

the keypad on my scantronic 7400 alarm system is not working do you have a replacement one in stock and if not do you have anything compatable that could be fitted instead

Hello! I'm in the process of building a home alarm that consists of the G2-44 Panel and I'd like to know a couple of things: Provided that I have installed a RF Portal, 1. Will this Glass Break Detector that Securitywarehouse supplies (Model: DOM-BG- work with the Galaxy system? 2. Will the KTC 805 keyfob work with the system? If I'd like to purchase the FlexGuard Glass Break Detector and Magnetic Contact (model FG-1608T) as well as the TCB8M Keyfob would it be possible for Securitywarehouse to order them? Thanks! Looking forward to hearing from you.

diy er order no#6419. have system installed and seems ok but not fully tested yet! in the absence of the installation manual could you help with some zone terminology. monitor, Ln fault and fault....then normal ky, bias ky, remove+ and remove-. I wish to have it set up for just "normal" pir detection. nearly there thanks...

Hi I ahve just purcahsed a Eurosec CP8L panel and a Pyronix Databell Plus Bell box, and would like you to confirm connections as this configuration is not listed in the manauls CP8L Bell+ Bell- Bell HO Strobe + Strove - SAB Tamper In the bell T T STB BELL 12v+ 12v- In addition is it possible to configure PGM1 to give 0v in Engineer mode to disable the bell box tamper. Various settings sre listed but not this one. Any advice apprecaited

Hello I have recently installed a Eurosec CPX system and was wondering if you have to add eol resistors to standard secware SC517 door contacts? Thanks in advance

hi just wanting to know what battery i need to buy for this sytem i have three sensors and one door contact and been told on 4 occasions differant ampage batteries

I have semi decieded to purchase/install an MDT alarm system and will be connecting a stand alone autodialler also I have used Texecom speech only recently but am curious if there is an easier to use alternative available? Do all autodiallers require you to record a message during installation or are there variants that come with pre recorded messages? Thanks in advance

Hello I have A CRT800 domonial intruder alarm system, it came out of the house of my girlfriend (we are living together now) And I thought ill build it in our house, It has enough doorsensors IRsensors etc, TAG reader and 3 tags It was a system with a subscription with (S.....s) But I encounterd some difficulties, first I needed the program to reprogram the system, via via I found DOMOPC. This works, but the cable I had to make was an different problem, I made a cable with the pinlayout that came with the software, and I can see some communication between the program and the system, but it fails over and over. Can somebody help me with a original cable, I ho…

My system requires at least 10 wired inputs and up to 8 wireless. What would you recommend in this case. I also want a system which can phone/message me if there is an alarm and can be remotely operated.

hi can anyonehelp i was installing a dc dialler and the led and back light were flashing as i was programming it the power went off and no it won kick back up again any ideas..cheers Kev

We have a Eurosec LCD panel intruder alarm in our house which we dont use, but there are 2 panic alarms in the house (little white box with red button on top and a little keyhole on the front), which are set to green so we assume are active (we havent tested as we have no keys to turn off?!?!). Does anyone know if you can buy replacment keys as my daughter is getting big enough that she is bound to press it soon and we are worried we wont be able to turn it off !! We would like to de-activate these alarms.

I have a scantronic 9800 system, could you advise me of the battery I would need for this system please. Also, if you have this battery in stock.

I am looking to replace an existing system (Elkron) with a new one and would appreciate any recommandation from an expert. I would like to combine wired detection (given available existing cable connection) and wireless detection (for new detection points and keyboards). I need to cable about 24 points (detectors, keyboards, smoke detectors, sirenes) and about 24 wireless points (windows/doors detectors, smoke detectors, IR detectors and keyboards) and would like detetors with some intelligence against false alarms (digital signal analysis?). I am currently looking at Risco as well as Texecom. I have heard Risco may be more difficult to program (only for registered i…