Intruder Alarms

would this be a suitable quality replacement for a failed pir on my OPTIMA XM6 home alarm box Bosch Blue Line Gen2 12m PIR Detector https://www.securitywarehouse.co.uk/catalog/intruder-alarm-equipment-c-36/movement-detectors-c-36_116/all-c-36_116_37/bosch-blue-line-gen2-12m-pir-detector-p-2291.html

Hi The receiver panel is a RFX08 and a 9751 control unit. The client has a 722 fob that will activate the panic alarm. However they have requested something like a one button alarm that can be attached to a wrist band/necklace for an elderly persons use around the home. Thanks PeterG

Sorry all you good people out there, to ask these questions , but I do not know whether it is I who is Dim or could the Electronics actually be at fault ?. When I try to register the keyfobs under other devices and I go to arming station I am asked to activate the tamper , A Is this the correct section to be in . B As there is no tamper do I just press any button or what. Also with regard to the Tag I am supposed to offer this up to the top left of the panel . I am in the arming station section but nothing is reacting. Again am I in the correct section and is there any way of verifying the Tag is working. I have proved that the Fobs are working by …

Hi, Can I please ask for some help on choosing a new alarm system for my 4 bed semi house with a garage on the side. The garage has a flat roof and there is a new flat roof extension being built at the back which will give access to 2 bedrooms. I have a living room at the front and a study on one side. The open plan kitchen/diner will have large folding patio doors at the back. The house is being completely gutted so hard wiring is not a problem and I have builders and electrician in at the moment re-wiring the place. I have been told about the Scantronic 9651 and 9751 systems and i would like a bell on the outside with LED lights and a number pad that can be cont…

I assume with the keypad I 1. open cover 2. disconnect wires (making note of what goes where) 3. wire up new keypad 4. replace cover, enter user code and test alarm

Good morning to all! I just purchased a Visonic 33 kit from SecWare, and I am experiencing trouble with regards to the communication between the panel and KP 250 keypad. I already opened a ticket with Support and awaiting instructions. Quite often the keypad stops responding whilst a "communicating..." message is displayed. In that case I need to remove the batteries from the keypad to get it working again.. Sometimes communication between keypad and panel is lost completely (a message "no communication" is displayed). The keypad and the panel are in close proximity and I tried relocating both units to no effect. Also,enrolling devices is a hit and miss situatio…

Hi all, I'm new to the forum, it was recommended by a member on another forum. I was wondering if anyone has a .pdf copy of a veritas r8 installation manual for the pre-1999 models please? We have 2 veritas alarm systems on our house, one was installed in 1995 when the house was built, the 2nd was installed in 2007. I have a manual for the newer system but the older system I believe has different programming codes etc. Any help would be greatly appreciated. Andy

https://www.securitywarehouse.co.uk/catalog/intruder-alarm-equipment-c-36/vibration-detectors-c-36_56/aritech-gs610-shock-sensor-p-2831.html I have a wired home alarm system. Looking for replacements sensors that detect any force used to gain entry at windows (maybe referred to as shock sensors) Would this product be suitable?

I am also looking for an internal siren. Would you be able to recommend one suitable for a three bedroom house?

Hi, wondering if i could get some help setting Honeywell ADE Informa Speech Dialler. it works as normal when the alarm goes off.but how do i acknowledged the call and stop it to keep calling. Is there a technical help line where we could call and speak to someone?

I have a domonial Crt 800 ++I have a problem with setup of the alarm system becourse I do not have the installation software. I thought it was enough to buy the TCU4-800M but I can not get the alarm system to work together. Is there an another way for me to program the system, or do you have the software and necessery cables to get the alarm to work.

All four (IS215T)of the pir's not working thus setting the zones as triggered, i tested the board and you get 13v across the two terminals, if you loop out each zone the alarm works fine. But obviously has a fault on it, to wipe out 4 pirs all at once. There is no explanation to why they have been set off, as the room was empty, then another pir would do the same, but on a different time of day etc this is without the alarm being set, no tamper is being recorded on the LCD key pad. Now all four zones with these pir's fitted have the alarm triggered on walk test and the alarm wont set, there is 13v power at the panel and the pir end all wires have been continuity check…

ESP Optical Smoke Detector 12V With Relay Base PSD-212 https://www.securitywarehouse.co.uk/catalog/fire-c-38/firesmoke-detectors-c-38_39/esp-optical-smoke-detector-12v-with-relay-base-psd212-p-5303.html Will this fit an accenta g4 alarm panel. Four connections positive negative two more wires for trigger to zone 8.

I have a client that requires a system with proximity fobs rather than a remote control keyfob. I have been checking existing cabling and conduits in the house and believe that I will be able to hardwire the remote keypads, although I would still like to maintain wireless PIR

Hello I'm looking to see if anyone can help I've recently bought a eurosec cpx control panel and I was wondering if I need to wire an additional power supply so I can connect the 7 pir's and 4 shocktec door contacts, Or is it possible to power them via the aux 12v. The pir's nominal current is 16mA and the door cont's 7.5mA, according to my calculations this will over-load the system. If so can anyone recommend a suitable add. power supply so I can split the load.

I require a flush door contact to be fitted to a wooden door. Can you please recommend a product? As I am confused by the terms \\\'Grade 3\\\' \\\'Grade 2\\\' and \\\'Green Resistor\\\' \\\'Red Resistor\\\' I will be purchasing the Scantronic 9651 (not sure if that makes a difference)

I've just installed an Accenta G4 and have a problem using the set output with the latching option of the Texecom IMPAQ Plus detectors. The Accenta manual states that the set output is positive 12v upon successful set of the system and removed when a correct access code is entered. However when I test the output from the main board, it is 12v positive when the system is unset & removed once set, so opposite to what is stated in the manual. The detector instructions state the same as the Accenta manual for latching, positive when set, removed when unset. Is there a way of configuring this output or is it a fault with the Accenta as I can't find any reference to it i…

I am looking for a simple intruder alarm system for a large house. Not really interested in remote access and monitoring or systems requiring computers to load up and configure. Need 4 x RKP and 19 x PIRs. No PAs or door contacts, though will want to use PA functions on all the RKPs. I really like the simplicity of setting up and using the Accenta control panel, but am I right in thinking that 8 zones are the maximum available for PIRs? I could easily group together 2 or 3 PIRs on some of the zones but that can make fault finding more tedious. Would appreciate you confirming number of zones available to PIRs on Accenta Gen4, also any suggestions for another product.

I have a cooper security 9651 panel. I'm rewiring the panel from global tamper to FSL because i've been told its more secure. I've wired single PIR zones with no trouble but when there is more than one PIR or surface contact or Panic button it shows tamper in walk test. If I one device is open at once in a zone, its fine but if I open two or more devices in one zone, the panel detects tamper. (E.g. When I open one door in Zone 7, the panel doesn't say tamper but when I open a door and a window in Zone 7 the panel will detect tamper) Can someone help me with this problem? Thanks Krishan

got around to installing the pyronix twin alert and the bell output is nice and loud but the spk just clicks? I have it set on a entry/exit output on a galaxy G3 panel and have moved the volume control. To debug I moved the wire I have going to the bell side to the spk and it don't sound? I even tried using the pull up resistor, still didn't work... I know I was somewhat brain frazeled by the time I got to do that (I even wired a sensor to the wrong zone lol) and wondering if I have missed something.. +12v -0v Spk switched to 0v Bell switched to 0v

Optex 20m External Twin Beam https://www.securitywarehouse.co.uk/catalog/cctv-equipment-c-1/detection-c-1_24/optex-20m-external-twin-beam-p-84.html Hi there, I am looking to have this type of system used in my house. To cover all usual access’s. Could you advise what infrared systems would be best and what control panel to streamline them with?

Hi, i am wondering if anyone could tell me what the bell terminals are on the euro 12 board and also could i use a euro mini keypad on this system ? thanks liam

Hi, do you have any ACE transmitter keyfobs for the Gardtec 593? I would need 2. Many thanks in advance.

I have two garage doors, roller shutter style on my house in need of connection to the Visonic powermax complete system installed. Is it possible to use the "MCT-100" connected to a couple of "Knight Plastics F10C Roller Shutter" or do you have some other recommended solution for garage door protection?

Please can somebody tell me if the Honeywell SEF8M will work with a Flex 20 panel and RF Portal (A073-00-01) Thank you