Security Lighting

Hi there, I am looking for a solution if possible for when my customers intruder alarm activates for it to be able to switch on external floodlights? Is this possible with your single control zone unit ie 1803 range or similar. It will be attached to a Texecom Veritas Excel Intruder panel , possibly connected to the bell -ve trigger.

Can you please tell me which one of these two products, GJD Mini Opal External PIR or Opal XL 12V PIR 35 m works with an older version of a GJD controller - it has a 6 wire configuration. The old ones - have disintegrated lenses due to UV light - they have GJD on the inside of the housings and they have a pan-tilt PIR but no model number if this helps. I've looked on your site regarding the new types of controllers which are very similar to the type that have been installed. Once I know if either are compatible I will need to order.

i have a 2 zone touch control 12v 120ma power supply unit with the code gjd exp mk4 printed on the board, it is only putting out 4/5 volts do you have these in stock. thanks Carl

Hi, I have a Honeywell Galaxy G2-20. I need to use a relay to connect an output to a GJD lighting system 15:32 Would the TKC relays be best for this or would you recommend a different relay?

Hi I just bought the above unit....do I need another piece of equipment to operate this unit as I was under the impression that this unit had a light incorporated and was an all in one unit....is it just a sensor and do I need to fit another piece of equipment, if so what??

I have a number of lighting sensors on our house and one of them seems to have stopped working (they've been in place since '99). Do I need to replace the whole sensor or just the bit inside?

Sales can you please source and add the GJD910W to your web site?

I currently have a GJD 2 Zone Solitaire one of the zones the light keeps getting stuck on once activated and does not turn off unless manually turned off at the panel. It has been suggested I may need to replace the zone controller, would the dygizone be a straight swap for the solitaire as I cannot find that model anywhere .

I have a Racalite Light control system running 4 external lights via 4 sensor heads. The sensor heads are the type supplied with a Guardall Excalibur system. I am looking to obtain 2 replacement sensors capable of operating on the current system. Specification of current sensor heads is: Power: 10-16v dc Temp range: -20 to +55C Steering Adj: +/-90deg horizontal +10 to -50deg vertical IP rating: IP55 Detection range: 17m 100deg field of view. Can you supply 2 suitable sensor heads? If so how much?

customer has a voltek security light system. 1803 controller with 2 sensors and an internal alert. the sensors work, triggering the internal alarm, but there is no output for the 2 floodlights. i have checked the 20mm fuse to the immediate right of the 240V output terminals and it's good.i suspect that the 1803 is faultybut would like a 2nd opinion before buying a replacement.

I have a 4 Zone Expansion Unit, GJD040 and a DygiZone enunciator and lots of Mini Opal PIRs. From one of your leaflets it shows 4 PIRS connected to each of 2 expansion Units. My GJD unit only seems to have provision for only 3 PIRs (A1,A2,A3). Is this correct or have I missed something? The two expansion units in the leaflet may have been Solitaire units. If 3 is the maximum can I double up? ie 2 PIRs in parallel? I realise the digizone will not be able to discriminate between the two but I guess it may work? If I was to purchase a second GJD040 can the two be connected together? How would the digizone handle Zones 5 and 6? Or would it be more sensible to have two separat…

RE: Takex PR-11B Hi, I plan on purchasing one of these devices as part of a home automation project to detect when a car drives on to my driveway. I was planning on attached the dry contacts to a binary Z-Wave detector to initiate some other lighting. I was wondering what the best source of power for the sensor would be - are you able to recommend any low cost power supplies? Thanks,

We have recently moved into a new house, and ive been trying to work out why the front security lights are not working. it looks like we have a voltek system as in the pics below the proximity alarm beep works ok its just the lights don't come on, and yes we have changed the bulbs thanks marc

One of your Opal XL products was installed yesterday as a replacement . The new product switched on automatically in response to movement after dark but the lights remained on and would not then switch off automatically. 1 Is there a control device on the unit for managing the time that the lights are activated or can you suggest another solution please. 2 Do you have an installation schematic for the product ?

Hi, I have a Voltek 1812 controller and the lux setting does not work. So I bought a new 1812 complete and still no good. It either senses and works both day and night or if I turn down the lux setting nothing works. The TLX override works fine. I have followed the instructions but simply cannot get it to work correctly. Very simply just to come on when it dark. Am I doing something wrong? Any ideas.

Hi, I have a GJD emerald mk3 system with 3 sensors and 3 lights and I hope somebody can tell me why the lights are coming on in daylight. Nothing has been changed on the system and for about the last 3 months they have been plying about!!! The system is quite a few years old now and I was wondering if the opal sensors or the main panel should be replaced. Thanks Steve

I was dissapointed to find the Bosch blueline range were not suitable for outdoor use as I have request for a backdoor light in a rural environment where bats birds and badgers roam freely. Does anyone know of an equivalent product product without getting into expensive wireless systems? The other problem is that I would need either two of these units or one that would have a wide enough angle to operate on a corner

Hi I bought a system from you last month and have now installed it. I bought a GJD digizone controller, 4 way expansion unit and Mini Opal pir's. The system often works well but every now and then a red led flashes inside the pir's and the system dies. It sometimes dies for minutes or hours then seems to reset and come back on. Do you have any idea what causes this?

Have just installed a 4 zone controller, DygiZone (GJD910) and expansion panel (GJD040) with 7 Mini Opal external PIRs (GJD 332). During the installation and initial setting of the PIR’s I had to remove each cover several times. Some of the PIR’s retained their Hex retaining screw with a plastic washer but quite a few them fell out. Inevitably with such a small screw I managed to lose 2 of them. Is it possible to get hold of replacement screws and washers through security warehouse? If not do you have the specification? I could do with at least 6. I have also recorded a voice message for each lighting zone but the quality of the recording isn’t very good. Sounds like …

I have a security light with chime alarm.My plug in alarm has stopped working.It looks looks identical to your model TLRXC1. My alarm has the type No BQ-RF-PTC-RX-W, 433MHz stamped on the back. I wish to buy a replacement alarm, my question is, will your model TLRXC1 work as a replacement alarm?.

CAN THIS BE USED OUSIDE TO CONTROL TWO OUTSIDE LIGHTS?

Having a problem with the new units : Initially both TX units were recognized by the RX unit and worked correctly but after about 15 minutes one of the TX units ceased to be recognized (the PIR is working since the LED flashes on the TX unit but the RX unit is not responding). Have disconnected and reconnected power to both TX and RX unit and used RX program mode to attempt to re-detect TX unit but still no response. Is there any other "reset" procedure or is the TX unit faulty?

My problem concerns our home security lighting system. We have two floodlights, two PIR's and an internal control panel. The control panel inside says GJD Sapphire MkIII. After several years of faultless use it has now gone wrong. Sometimes the lights only flash, sometimes they are ok. I think it is either one of the two PIR's giving a faulty signal (with the other still ok hence it sometimes works) or the timer in the control panel. I tried altering the time on this and they seem to stay on longer when they do work, but usually they only flash. Should I change one of the PIR's or what. I really would like to talk to a real person!

Dear Sir or Madam I want advice and information on products that you might have that would suit my needs. I want to automatically switch on my driveway lights when, after dark, a pedestrian or vehicle comes into the gateway or starts up the driveway upon leaving the house, so I will need two sensors. I would like to use break-beam technology rather than PIR so that I can have the beam approximately 75 to 100 centimetres off the ground where it will not be triggered by dogs etc. I expect that when the beam is broken a signal will be sent to switching circuitry inside the house which will turn on the lights. The lights should stay on for about 5 minutes before turning off a…

could you please advise on a psu unit to power 3 optex vx402 units and 12 volt to 240 volt trip relays to power 4 500w flood lights on a barn inc 1.2 amp 12 volt backup.