Intruder Alarms

Does the Honeywell AG6 SAB and Cover (Blue Strobe)have led indicators on perm or flashing, to indicate power is there and it is not a dummy box.

Hi I want to use the Visonic Discovery Quad wiireless detector to protect a garden shed approx 25 meters away from the panel. do you happen to know if this particular wireless item is relaible or would you advise using hardwired ?

Hello, I am looking to purchase the Honeywell Galaxy 2-20 Wireless Starter Kit together with additional items (internal and external sounder, additional sensors, etc.). I am good with general electrical / electronics work but never installed alarms before. I can't find installation guide on the internet to see how easy will it be to install and configure the system. If you have installed this or similar system, could you please share your experience? Thanks

hi, i am after a wired heat detector that is compatible with the hkc 1070. Im looking at the texecom products? many thanks

When fitting a Scantronic 9651 panel recently I noticed it had a rechargeable battery soldered onto the PCB. I guess this is to maintain settings it case of total power failure/disconnection. Does this have a design life of 5 years like most other re-chargeables?? If so it doesn't look like it was designed to be easily replaced. And how would you know it needed replacing anyway - until it's too late? Phil.

Hi, I have a Castle care-tech euro mini and need to add another PIR to a FSL zone which already has a PIR. i.e. I need to wire two PIR's in series. Unfortunately the manual does not give any details how to do this and I have not found any helpful information on the net either. I would be most grateful if someone can point me in the right direction to achieve this. Thanks in advance. Mel.

RISCO Group have a product update A new firmware update has been introduced to the Wisdom wireless control panel. The new version of the Wisdom firmware is V4.31, updated from V4.27 Why have we upgraded the WisDom panel The following fixes/updates have been modified to bring you an improved panel. Technical The panel has a new menu to show the connected BUS AGM IMEI number (Used for IP Receiver) The Blank Display has been updated in that you now only need to enter your code once. The

upon power uo of my recently purchased optima gen4 copact alarm the alarm sounds- enter code 0123 and the alarm siren silences. i have no flashing tamper light despite the cover being off,i have a flashing sos led which will not go out whatever i press? i have the global tamper pa & ta terminals shorted out but still am unable to extinguish the sos led. do you think the unit is faulty or am i missing something obvious

I am looking to upgrade the security at one of our premises using a Net enabled alarm and CCTV system I note one option is the new Honeywell alarm system in the Galaxy range , assuming you cover it, could you pl update the costs for the model called Galaxy Flex. Also wanted to know if you have option to connect outdoor IR Sensor at the perimeter, to these alarm system. My local engineer told me that I-on 40 that you offer can be connected to these systems, eg BX-80N or NR model from OPTEX. Can this also be connected to galaxy model eg dimension flex etc

hello, im looking for a new larm system. i am building a new house right now and want a wire larm in it. not wierless. i also want to oversee thing in the house with like Hidden or discret cameras. do you have anyting for me? i also want to control the larm by my phone, oversee the alarm and get email or sms when something hapends. the larm system should have4 or 5 cameras, 4 or 5 motion detektors , if its imposseble to have de cameras inside the detektors that skuld be great. it also need 12 magnetic contacts. and if its possible, not necessary but if its easy. i want a passage system outside the out door and a electrical lock so you can open with a tag or a code. i also…

I am working on a project with one of our clients. We are installing Gallagher system for them - https://security.gallagher.com/. One of their requirements is to have wireless sensors on windows connected to the Gallagher system. I was told i could use this Wireless Receiver. But do you know which sensor i could use? For example we have Ajax sensors on hand. Do you have any experience with this type of setup? look forward hearing from you.

I have replaced an old Optima panel, (18 years old) with a new Optima Compact. All works fine except the LED in the PIR does not flash like they used to when I walk into a room and the alarm is not set. You can still hear the relay click in the PIR. Only the panel wiring has been touched. Any suggestions what to check as I have already checked the wiring, or does the new Optima panel work slightly different than the old one. Robin

Hi could you please tell me which fire alarms and relay bases are compatible with the Optima Mini Gen 4 intruder panel. Looking forward to hearing from you

hi there can you please help asap i have got a pyronix bell box off you and a veritas alarm system i have installed it for my costumer and every thing works except when the alarm goes off the bell box does not the strobe works and when you take off the front of the bell box it stets off the alarm and works it self .

I have a omnicron 7000 and i wish to change the controll panal i was wondering if you had a panal that would be able to be put in its place and i could just rewire my sensers back in to

I am interested in the wireless detectors for my home. (outdoor) Blueline PIR Detector We live on a very large property with three large dogs in the garden. 2.What I would like to do is divide the property into 4 security zones which can be armed and disarmed independently. I was thinking of placing about 4 or 5 detectors in each zone. Could you make any suggestions? Do you think that the above detector will be right for me? Next, I would like to hear your opinion about the receivers and/or control panel that I would need? The control panel (alarm system) should be armed and disarmed by using a remote control. My other concern is that we often experience po…

On 30 April 2015 you delivered my order including Scantronic 9651 + 9943 keypad,, 2 off Guardall PQ15 PIR, plus cable and brackets. I hang my head to admit that I am only now finishing the modification to an existing system for which I ordered the parts. Cause of the change was that the original installer had run one cable to 2 back-to-back PIR, and the cable route was forced in beside central heating pipes etc and seemed to be frequent intermittent giving faults. I have resited one PIR which I replaced with a PQ15, and added an additional PIR to the system. I ran new cable to both PIR. While I was at it, I added a new additional 9943 keypad in the master bedroom (the ca…

Could someone help with connection for new box please,ive cut the cables on the old lexecom box but not sure on connection for new box,I am a spark just never worked with alarms Thanks Tony

Hi how do I omit a zone on key a control pad 9651 /9941?

I am about to place an order for a Scantronic 9651EN-41 (9651 c/w 9941 rkp)with a remote keypad and tags etc. You do not seem to have a Scantronic external sounder. Are all the sounders you have of othr makes compatible with this control panel?

I got a speech dialler a few months ago been, working well untill a round 2 weeks ago. it's stopped dialling out or reciving calls. I have plenty of credit phone, and the sim card works in a mobile phone. the antenna is ok no damage that I can see. do you have any ideas on what the problem is?

iam looking to buy a 800l control panel but i have noticed that they are sold out any chance if you are going to restock them

I have two wire LS 400 alarm in my garage. I need a couple of new PIR sensors. Do any of your sensors work on a two wire system?

Can anyone recommend a simple wired alarm system with support for maybe 2 door contacts, and 4-6 PIR's. I'd like one with GSM support to SMS me when an alarm event is triggered. Any other fancy features like internet monitoring would be nice, but not necessary. This will be for domestic use - and only used very occasionally i.e. - when on holiday. No pets in the house. Thanks,

FIrstly: Iam from Finland do you also ship overhere? Iam looking for wireless door switch system like Visonic. I believe this is good quality system? I have separate home automation system where i would like to integrate this. Can i do it with Receiver MCR-308 8-Output Wireless PowerCode Receiver? I mean if i have 4 door switches and and carbon oxcide detector and maybe some other then i can contact with 8 different sensors to my system? Does this unit include already relay to make conatact for 24VDC system? Can you provide such relay if its not included? How much its cost? Iam also looking for RFID system with single relay output 24VDC and some 8 tags. This would nee…