Intruder Alarms

I need to replace a PIR motion detector for my home alarm system. The sensor that needs replaced has 7 terminals at the top of the circuit board. They are: 12v power +/-, Alarm NC x2, Test x1, Tamper NC x2. Do you sell a detector with the same connections? I tried a Pyronix MeQBlue but it only has 6 terminals (no Test terminal) and also the terminals are at the bottom of the board and not the top ( the cable length and positioning are quite limited). Thanks for your help!

It keeps sounding at random times, with no tamper fault and no error message on the control panel. The problem seems to lie with the sounder only.

Hi, looking to but the Texecom Kit 2 32 Zone Wireless Kit with Sounder but have some questions. How is the Premier LCDP powered... batteries of PSU? I assume the LCDP is wireless to the main control box? I have a couple of locations I would like to 'hard wire' will any 'standard' PIR be suitable for this? Is it only 4 hard wired channels I can use? Think I need a cover for the bell box with this kit? please point in right direction for this please

According to installation instructions for AG6 sounder PCB should be marked as follows TR- V- ST- V+ S- The actual PCB is marked ST- R- SW- V+ V- Can you confirm R- is actually TR- and SW- is actually S-

Hi all... i'm trying to locate some gartec 350 plus RKPs to connect to teh main control panel, does anyone know where i might have any luck getting any - i'm aware that they have now stopped doing them, was just wondering if there are any surplus left - also does anyone have any gardtec 350 CPs for sale? any help/advice would be appreciated. thanks in advance bob

I am sorry to bother you again. Can you tell me please is it possible to get a wireless sender and receiver to fit inside the VERITAS R8 control panel as we have a garage that was alarmed that way as it is detached from the house and the old wireless sender is not compatible with your system. Also is there a code to open the panel to replace the battery as the installer took all the installation notes with him and he has gone to Australia for 3 months so i cannot contact him.

My wireless home alarm system has been jammed by source unknown. I have reset it but would like to back it up with hard wired system, not susceptible to jamming, for the upper floor of my house. Could you suggest components for such a system. I would like it to include Two PIRs (no need for pet friendly type) A remote wired keypad which can be set/unset easily without keying in a four number code ( I would like to either press one button or use a proximity tag, unless its operation can be jammed) A panic button (unless its operation can be jammed) Outside bellbox with battery back-up (not Odyssey) Thanks

Does this come with a battery ?? If not, which one do I need to order for it. Which Remote keypad do I need to order for it.

My current alarm Guardall Rascal Super is broken so needs replacing(we are using 4 programmed zones and chime). I'd like to replace the control unit unit and bellbox but use existing wiring, sensors and internal speaker. I'm looking at the MDT Avanti 8 and AG6 bellbox (current bellbox looks tatty and has no strobe). 1. Is the chime quite loud? We would like to hear if someone enters the house from the other side of the building. 2. The Rascall Super system is 12v and I think the Avanti 8 is 13.8v, will our existing sensors work with the new control unit?

Hi, I am installing a Honeywell G2-20 alarm system at my home. I currently have two iWise 800QG3 movement sensors and am looking at installing an additional four to the system. I am considering purchasing the following detectors. https://www.securitywarehouse.co.uk/catalog/bosch-blue-line-gen-2-bld2-pet-tritech-blueline-detector-p-2392.html I understand TriTech is the best class of motion sensor to reduce false alarms. Is this sensor recommended or would you recommend something else? Any advice is much appreciated. Kind regards,

hi I was just wondering what control panel I would need to buy with the Klaxon 127Db 240v High Output Master Blaster Siren (12v Relay)I will also need 2 P.I.R's. thanks in advance.

Does anyone know anything about this alarm system? It just keeps setting itself off without us setting the alarm. Its keeping us up at night and im getting desperate. Someone please help with any knowledge at all. Oh and it doesnt let us reset the system at all!

Good morning I wondered if you could help, we have fitted a ali door to a business which has a Chubb alarm system, and the Chubb engineer has said the below. "The lock or keep needs to have an integral micro switch contact on it to provide electrical connections. Giving common, normally open and normally closed options for the connection onto the alarm" I could really use some help with this from someone who knows, I do have pictures of the door if i can send them across to you. Wondered if you had i stock or could get what i need, Thank you

Hi, I\\\'m after a reliable wireless system, 5 zones down stairs one of which is a gargae, 1 zone upstairs but a pir would not be suitable in this area. The sounds to be wireless operated but mains powered. I\\\'d prefer a keypad activation & deactivation. Also is there a posibility it can notfiy you via text if your alarm is going off.

Having just been burgled I have purchased a KX15DATM pir from you to replace a failing unit from a different manufacturer. The existing unit is connected via 6 cables - 2x Tamper, 2x Relay and 2x 12v. Do you know what connectors the cables need to be screwed into on the KX15 please? I may also have to change some of the dip switches? The control panel is an Accenta 8.

Hello I need to replace an wireless siren MCS-710 with a new model MCS-730/740. The control panel is a PowerMax Plus SN:15408.9BA2 JS700611 V3.4.08. Can you confirm that the MCS-730 and or MCS-740 are compatibile?

I am looking to upgrade my scantronics 9800 alarm system to remote control arm and disarm. I want to keep my exiting pir's and door contact and outside siren/ strobe box. Also I would like to keep the option of the keypad as well. I was looking at the LGSIX/01 unit. Will this unit do what I want. Also do you do any other remote control units that will work with this unit.

I am interested in this product https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/wireless-ia-c-36_60/takex-wireless-ready-external-pet-tolerant-12m-pir-dual-head-p-2040.html I want to buy two wired sensors: https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/movement-detectors-c-36_116/all-c-36_116_37/takex-external-12m-pet-tolerant-pir-dual-head-p-2038.html and two wireless sensors (the first link i just sent: https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/wireless-ia-c-36_60/takex-wireless-ready-external-pet-tolerant-12m-pir-dual-head-p-2040.html I want to connect those wireless sensors (as above) to a Paradox EVO 192 centr…

Was wondering if anybody has detail for the Scantronic Plug-in footprint used by the 960? I wanted to hook this speech dialer up to an alarm that does not have the Scantronic footprint. If I could get hold of the spec for the two connectors of the 960 I could then jury rig a connector (or spade terminals) to tease out the 4 standard triggers as well as the line fail signal. I could also take care of any other inputs that need to be dealt with. Any ideas? I've done an extensive web search for detail of the footprint but have not found anything. Thanks John

I am about to order the Scantronic Homelink 55 from your site but have a couple of questions... Can I add an extra keypad with prox reader? The description of the Homelink mentions only the 9940 and 41 but they are no longer available I think? Will the Scantronic PIR's (wired types) work OK with the system, as I only need wireless contacts for the doors, all other sensors will be wired? Any recommendations for a suitable external sounder?

I need cable and software to program Galaxy 2 over PC, Please let me know what kind items do I need.

Hi, is there a way to gather more logs for zones that it is currently available? I have 4 zones and there is 250 logs for each zone.

MDT Avanti LC Steel Control Panel https://www.securitywarehouse.co.uk/catalog/intruder-alarm-equipment-c-36/security-control-panels-c-36_102/control-panels-all-c-36_102_41/mdt-avanti-lc-steel-control-panel-p-1000.html Hi, can this unit ( Avanti LC 9EP309 ) replace an old ( Avanti XP PLUS Steel Panel unit - Product Code - 9EP322).

What is the best course of action - I have a Homelink ( Scantronic) 75 Security System installed over 3 yrs ( the installers have gone bust and I cannot therefore get the original installers to maintain system) Over the last 6 months the system as gone down specifically - the passives batteries. Can I simply replace batteries with lithium AA cell batteries will this restore the system to normal functuality at the control panel or does the new batteries mean a total reset? Secondly, can I add further 2 passives (I believe I'd need the Scantronic 714R passive infra-red detector & transmitter) and a panic alarm or do I need professional installers due to complexity…

Hi I am looking for an alarm for a workshop/shed, 1 opening window, 1 fixed window and double doors. I have used Scantronic previously and therefore would like the following:- Scantronic 9448, with 2 contact switches, a glass break sensor, Elmdene INT400 and a battery. (I have avoided PIR\\\'s because of false alarms) Could you advise if this is suitable or are there better options, please advise battery type for above.