Intruder Alarms

My wireless home alarm system has been jammed by source unknown. I have reset it but would like to back it up with hard wired system, not susceptible to jamming, for the upper floor of my house. Could you suggest components for such a system. I would like it to include Two PIRs (no need for pet friendly type) A remote wired keypad which can be set/unset easily without keying in a four number code ( I would like to either press one button or use a proximity tag, unless its operation can be jammed) A panic button (unless its operation can be jammed) Outside bellbox with battery back-up (not Odyssey) Thanks

Hello, im intrested in a vsonic kit with gsm module, does it have gsm already installed or its extra purchase. It should work on 868mhz. WHich one do you recomend with theese demands, kind regards

Just purchased a host of intruder alarm equipment from you - it arrived yesterday. The control panel is the Texecom Premier 48. Does this panel have an intergrated sounder that will sound when the alarm is activated (entry/exit and on activation) or do I have to buy something additional?

I have an accenta g4 alarm system and would like to be able to arm/disarm it using mobile phone. Please can you let me know which diallers I can choose from that would be compatible? thanks

Hi! Can anyone give me a reason to why my PowerMax+ have started to set off "Trouble alarms". Almost the same alarms every time. I need guidance in what to look for. When I check the log, it shows: * System jammed * Line Failure * AC failure (only the first time and the power were on all the time) and then * RF Restore So far it has happened twice in a month. Both times when the alarm is off (the first time the alarm were set off half a minute after disarming the alarm from HOME setting, the second time about 30 min after disarming AWAY. First time, the alarm were reset while I was checking the log (less than 2 min after the alarm set off), the second time i…

I ordered a Scantronic I-ON 40 from yourselves and I would like to protect my integral garage. Can you let me know whether an additional Scantronic EXCELR 12m Wireless PIR (XCELR) would suffice? Or should I consider an alternative trigger for the garage? Also, can you let me know which remote keyfobs work with the I-ON 40? I ordered a Scantronic I-FB01 Remote set/unset Keyring Fob (I-FB01) as part of my original order which does not appear to be compatible

I purchased a Meniver SD2 from you a while ago and have just got round to fitting it but it isn't working and I'd like some help to get it work. I have wired the autodialer into an alarm system and all appears to be good until the unit goes to dial out. I have run test facility and the unit opens the line and then dials, it's says on the screen wiring to dial. I can hear a dial tone before the dialling but the call does not connect. Then before you can hear any connection to the dialled number the unit starts to send out the recorded message after a few seconds. The line test on the unit shows that the line is ok and the fact that a dial tone can be heard before it dials…

Hi, can you please tell me prices of the below: 1 x Visonic Powermax+ 1 x Extarnal GSM adaptor 2 x Wireless motion detector (works in dark, no pet) 2 x Wireless door/window 1 x Wireless Glass-break detector 2 x Wireless smoke detector Can you estimate the freight to Sweden?

I have purchased the Powermax+ from you last year. Am redoing the electrics in my place and rolling electrics to my cabin. Was wondering how I can connect my cabin to this alarm. Is there a way of connecting a PIR via a cable?

I was wondering if the Powermax Pro kit you sell supports Partitions? As the description says its optional. Thanks

Hello there, Could you, please, help me finding which of your system would be most suitable for my needs? I am looking for alarm system for the house and 2 wooden bike sheds 7 meters from the house. The system for house can be wired, the system for sheds must be wireless. The house system will need 5 PIRs, one of them should tolerate a tortoise (25cm, 2 kg, in a heated enclosure in the hall), 2 door contacts, 2 sensors for windows (breaking glass or vibration?). There are both, a land line and GSM cover, in the house. The system for the sheds should probably have 1 door contact and 1 PIR for each shed, PIRs could maybe replaced by vibration sensors attached directly t…

Would any one have a manual for the panel. The one I'm working on is about 8 years old. Cant find a manual anywhere, want to check the manual before I condemn it! Thanks

please confirm that the DBA-0001 Texecom Premier LCD Keypad is compatible with the Texecom Premier 168 Control Panel. Thanks.

Currently have A Veritas R8plus 10 years old that is now faulty. Would like to replace with a new one, is current model a direct replacement to old. Does new unit come with battery. Can it be replaced by DIY

I was just wondering if I can use IP telephony to connect to the alarm system. I know that it works with PSTN but I have my telephone via broadband modem(however I use a traditional telephone set connected to the modem

I have recently changed a Optima compact Gen 4 panel as a favour for someone. The first panel that was bought through Amazon had a fault on it. A second unit has since been fitted and all is working except the new Siren which is a Reson 8. The unit comes with pre-fitted links across TA TAMP and PA. The manual states that these should be in place when powering the unit up. This contradicts some advice on online instruction that says to remove the link to T A when wiring the siren. The external siren does not sound or flash when an alarm is activated, internal sounder in board works OK and all zones work fine on a walk test. No LED,s in the siren are vi…

Hello, I have a Visionic Powermaster 10 alarm system that I want to upgrade to connect to BroadBand. I believe the unit I need is the Powerlink 3? I have a couple of questions ... Is this the right unit for my alarm? Once connected to my home router, am I able to use it right away, for example, through a telephone app, to monitor my alarm system, any ip camera etc? Do I HAVE to subscribe to any third party service or is that just an extra option? Thanks

Hello Before i order Galaxy Flex GSM Module, i want to know if it works in sweden?

Hi, Please can you give me some direction on wiring SD3 GSM Dialer to an Accenta G4 mini panel. I want to be notified when the bell goes off and to be able to reset alarm system remotely. Also do i need to install a relay? Thanks, Jeramy

Could someone help with connection for new box please,ive cut the cables on the old lexecom box but not sure on connection for new box,I am a spark just never worked with alarms Thanks Tony

Have Securitech 700L control panel which needs replacing. Will Honeywell Accenta MiniGen 4 be suitable and retain existing wiring and PIRs?

My Honeywell Optima Compact intruder alarm system, now 16 months old, is activating tamper alarms at random times, in both Day and Set modes. These reset straight away. I have linked out the panel terminals for both the sensor tamper loop and the remote LCD keypad tamper loop, which takes a wiring or tamper switch fault out of the equation. The tamper alarm still activates every couple of days (or nights .... it went off at three this morning!). Question; does this indicate a control panel hardware fault or a software fault? And if the panel is faulty, is it still under warranty?

I'm seen your texecom starter kit - New Texecom Ricochet Kit 2 64 Zone Wireless Kit with Sounder. I want to buy a texecom direct wired bell box. Can I wire that into the control panel for this kit or will it only work with a wireless bell box? Does the Texecom AEB-0001 Impaq Plus Shock Sensor Grade 2 work with the New Texecom Ricochet Kit 2 64 Zone Wireless Kit with Sounder. Also is there an option to have the system txt me when its set off?

I've been looking on your website and I've seen 2 products I'm interested in: ADE Honeywell Accenta Mini Gen4 with LCD Keypad. One has a product number of: 8SP400A @

i ordered and installed an ade alarm system, the customer has asked if i can clear the event log, i have looked but this is not shown in the manual. can this be done ( hopefully from the key pad )