Intruder Alarms

Scantronic EXCELR 12m Wireless PIR will this work with my scantronic +500r panal please advise the frequency your help would be appreciated

Will my SD1+ still work when BT goes digital?

I purchased a SD 3 dialler off you approximately 3 years ago. It has recently stopped dialling out when the alarm has been activated. I checked the Sim card in a mobile phone and I was able to make calls from the phone, to double check I also bought a new sim card which again worked in my mobile phone but would not dial out from the SD 3. In the LCD display , next to the temperature there is a small box with a letter T in it. The sim card I use is a Tesco pay as you go, signal strength is the same as usual. I have tried to do a test call from the dialler and it failed with the message call error. When I have dialled in remotely the sim goes straight to answer phone , I wa…

On the display screen two lines of Pixels have failed making it difficult to read what is on the lower part of the screen, I have re-booted the unit but there is no change. Do you have any further suggestions for rectifying the fault?

I have a Securit 800L+ alarm panel. Fitted by the housebuilder. I need to remove the alarm panel for building work. It would appear the siren is a Self Contained Bell or a Self Activating Bell. When I disconnect the mains and the internal 12v lead acid battery the siren goes off. Would keeping the siren -Ve and +Ve at 9v to 12v keep the siren from sounding.? I have the installation manual for the alarm but I do not have any details of the siren box fitted.

Have Securitech 700L control panel which needs replacing. Will Honeywell Accenta MiniGen 4 be suitable and retain existing wiring and PIRs?

I have an Infinite Prime Alarm System installed. The alarm system has a PSTN module which I want to setup.I intend to run a two wires (blue/white and white/blue) from the master socket to the micro filter marked ‘from VDSL Line’.The two ‘OUT’ wires marked ‘To Modem’ would go to the two terminals on the PSTN module. Is this correct?Is the PSTN module performing like a modem? I do apologise for my lack of ignorance regarding the function of a PSTN module.Thanks

could you tell me if the system uses 12 volts as a battery backup ? i am looking to putting this system into 4 garages/lock ups where there s no mains power, but i could use 12v batterys if this system runs on 12v when no mains power avalable, also is it a 12v supply that activates the siren, thank you.

Hi, we have constructer a community hall with aluminium windows and doors. Do you have a door and window sensor which can be wired into the building security alarm or wireless which can be concealed in the frame? The Client does not like surface mounted door alarm sensors.

I'm interested in the texecom elite 24 alarm, can this alarm be set via a mobile phone or land line.

I purchased from you the Secware Texecom kit. I want to connect shock detector and open detector to a double opening UPVC patio door. I also want to connect a window detector to a UPVC window. Can you please recommend the appropriate products from your store. Basic to mid range equipment will be fine.

Looking for a shock sensor. I have an isolated gantry with access stairway. Trying to identify if there is a shock sensor / virbration sensor that can be placed on the metal structure that will send alarm when detection noted. Do you have a device that will perform in this manner

Hi there, If I use the Texecom Premier Impaq Plus With Built in Contact, with a Honeywell G4 alarm panel, can I use 6 core cable, or do I need to use an 8 cables to set the contacts up on zone 1, and the shock sensor up on another zone.

I am replacing an old system which is armed on exit using a shunt lock, I require a similar wired system. As we have a number of keyholders we prefer the final lock to arm / disarm the system in preference to a keycode

just installed above pir in a conservatory and there are cats it activated 3 times with and without cats is there any settings I should set for a small conservatory?

I live in UK , but have a holiday home in Spain ,and need an intruder alarm ( that doesnt need a landline ) to notify me of a trigger to my mobile phone .I dont really have any permanently resident and reliable close neighbours to act as a keyholder or lookout . A sound bell/siren would not be of help or long term deterant . Need ideas of a suitable system , and outline costs .

Hi, i purchased the simpleset reader with a G4 accent mini system in November 2009. I installed the system in January all worked great with 2 keypads and the simpleset at the front door exit point. This morning my wife set the alarm with the keyfob and returned 30 minutes later went to unset the alarm and it would not work.It just has a power on light and nothing else.All other aspects are fine and have tried a number of trouble shooting tests but its useless. Reading the forums, someone has had the same fault with a new item. Is the item under a 12 month warranty/replacement? We now cannot use the alarm which is a little worrying! Many thanks for your help.

I am looking for a SIP dialer module that will work with a Honeywell Galaxy alarm system

I have PowerMaxComplete. In page 13 in control panel i have make readings for Serie nummer. 51001.3670 JS 701049 V1.1.05 JS700421 V1.0.02 Please advise suitable siren and smoke detector.

can you tell me dose the snt duolink kit come with psu

I want to use 12volt bells as my warning devices but I've been told that they will burn out the microprocessors on modern control panels. Is this just a way for the trade installer to put me off doing it myself or is there any truth in what he's saying.

I require a standalone wireless receiver plus 2 IR room sensor to connect to an ADC type panel (wire to existing sensors has been cut by flooring contractor)... The Nova 2 would appear to fit the bill?

On 30 April 2015 you delivered my order including Scantronic 9651 + 9943 keypad,, 2 off Guardall PQ15 PIR, plus cable and brackets. I hang my head to admit that I am only now finishing the modification to an existing system for which I ordered the parts. Cause of the change was that the original installer had run one cable to 2 back-to-back PIR, and the cable route was forced in beside central heating pipes etc and seemed to be frequent intermittent giving faults. I have resited one PIR which I replaced with a PQ15, and added an additional PIR to the system. I ran new cable to both PIR. While I was at it, I added a new additional 9943 keypad in the master bedroom (the ca…

i have recieved the Sterling LCD keypad today it looks like i have been sent the latest LCD pad and my pad is approx 7yrs old. Is it compatible?

wanted to know if it was compatable with the older version