Intruder Alarms

I have recently purchased a Menvier SD3 dialler from you to use with a Honeywell GD4 Accenta alarm system. My electrician has successfully configured the Accenta Alarm outputs to work correctly with the SD3 dialler (texting and calling fine), but is having some trouble workling out how to connect the SD3 outputs as required as the manual does not give a great deal of info. I understand that the outputs are open collector and therefore will need a suitable relay to provide a clean switch. Can you please recommend any particular relay modules (boards) for connection of the following outputs: 1 - To control heating system on/off 2 - Wired back to Accenta panel as Panic …

I have an i-on16 Security Alarm an require 3 Door sensors could you advise which sensor I will need to buy?

H I am looking at the Honeywell Accenta Mini Gen4 control panel,and am not sure which Internal sounder is best suited for this system , the Honeywell Internal sounder or HCK Echo or CQR Piccilo . I was intending to wire the sounder into the control panel Any advise please

I'm just inquiring about your Klaxon h series burglar alarm sounded, just wanted to know is it compatible with a Honeywell accenta control panel and also is the sounder the same as shown its the picture?

I have an A083-01 that was working fine in a Galaxy Flex 20 up until about a month ago when the panel started to report line failures. Despite several resets of both the Internet and the panel, the error would come back within an hour or so (line fail sensing). The diagnostics on the panel report that the comms are all good. The LEDs on the A083 also suggest everything is OK (Green on 0.1, off 0.9 sec) Orange intermittent = ethernet. If I disconnect the 435 cable I get an immediate error on the panel, so it is being detected OK.I’ve replaced the Ethernet cable, used a different IP address etc, all without change.However, I cannot communicate in or out via the unit. Rather…

Trying to find a good quality PIR sensor for lighting control. Just to turn on about 200W of lighting for, say, 15 minutes when persons detected during darkness. One sensor, one output. Min range 30m. (It's for use in a churchyard.) Ideally a stand-alone unit, but could be a PIR head plus power supply / relay unit. I don't need manual overrride, timers, etc. If I used one of these, what additional kit would be needed? https://www.securitywarehouse.co.uk/catalog/opal-xl-12v-pir-35m-p-642.html Similarly, for this one: https://www.securitywarehouse.co.uk/catalog/voltek-single-head-external-sensor-long-range-black-1804lrb-p-1532.html Thanks.

Hi there I have an MCR-304 + 3 x MCT-303's in my basket. 2/. From your experience in the field what is the effective range. In my application I have a fair amount of brickwork through which the RF must travel - probably about 15M to the furthest 303 and about 3 x 9" conventional brick walls. 3/. Are the 303's 'supervised transmitters'. Thanks.

Hi, Im looking for a long range (reliable over 30m) outdoor motion detector to control outdoor lighting. It needs to be able to be triggered by a person or car but not trees and shrubs. I got a cheap one which picks up shrubs so my outdoor lights are constantly on and off! Thanks

I would like to purchase a system with 8 zones (7 for PIR and 1 for fire) and two remote control panels. An external bell sounder is not required but an internal one and alerts via the internet/e-mail would be required. Please could you recommend a system that would cover these requirements.

Hi I am interested in purchasing the Scantronic Homelink 55 system for use at my private residence - this will allow me to upgrade my existing system and utilise the alarm cabling with the added ability to install future wireless devices without the need to install any further cables. My query is this - when installing the alarm can all of the programming functionality be achieved by the use of the keypad included in the pack - or does any specialist device or software need to be purchased? Many thanks John

Hi Security Warehouse, I have been trying to re-commission my SD1+ after it being disconnected for several months. However, I cannot enter any 'user code' because buttons 1,2 and 3, (also A), do not respond when pressed. I would appreciate your help please. Regards, Chris Wills.

I have a 20+ year old burglar system. I plan to get Texecom Veritas R8 panel. 1. Are there likely to be problems connecting to existing bell and PIRs? 2. Do I need Veritas R8, rather than Veritas, if I want to connect Speech unit at a later stage? Thank you.

i'm sorry but yesterday i received your ex-35r optex detectors and, comparing with mine, i discovered that inside my detector there is one more transmitter, probably compatible with my General Electric "Simon" alarm. here you can see the manual (in italian) of my "Simon": http://www.hesa.com/index.php?page=shop.getfile&file_id=658&product_id=515&option=com_virtuemart&Itemid=37 in this manual it is written that Simon works with any "autolearning" detector SX ITI at 433Mhz. if you want, i would like to send you a picture to show the transmitter that is inside, and if you have it i can purchase, or if you have detectors compatible with my alarm system …

I ordered the above Visonic MCR-304 Receiver from you and it was quickly delivered without any sign of transit damage. Firstly my thanks for your prompt service. I installed the item in the prescribed way and powered it up. I then set the Learn jumper into the Learn mode and the yellow LED flashed as expected. I then pressed the Tamper spring and the yellow LED and the red LED both flashed OK and using the tamper key I was able to cycle through the various channels. I then tried to associate/enroll a known good transmitter and in this respect I used a MCT-100. This transmitter was free standing and located close to the MCR-304 so range was not an issue. I tried to force …

Can you provide visonic power master magnets to compliment the visonic shock/vibration sensor making it a shock/contact sensor?

I'm looking for a wired door contact that is compatible with the GD04. It will be on a shed door. Do you stock a compatible item?

I have just orderd a ADE Optima gen4 8 zone from you. It will replace a c&k Active 5. I have the Engineers code for engineering mode. The problem is I can not stop the bell box from sounding when I disconect the bell wiring or when I try to open the bell box. The bell box was fitted and suppled by Abacus and is about 3 years old. I hope you can advise . Kind regards

Would the Risco Novagard 6 Blue Live Backplate work with the ADE Honeywell Accenta Metal Gen4 with LCD Keypad or what sounder should one use with this control panel thanks

i am looking for a suitable replacment for a karizma + system that i installed many years ago, the system must use id type biscuits as the system was wired this way originally , can the castle euro one do this and if so can you supply it with a 125 khx prox keypad?

Can 1 dialler be used between 2 alarm systems that are within 100m of each other?

I am looking for some alarm PIR sensors that will operate on a 24v DC supply for use on a double-decker bus that is being converted to a Men’s Shed workshop. The standard bus supply is 24v and the alarm contacts would need to be either N/O or N/C as the alarm control panel does not use EOL resistors. Please could you suggest some suitable devices.

Hi, I'm an installer looking for a 6 zone wired panel with option to expand using app, What do you suggest?

I recently bought 1 x scantronic 768r receiver and 8 x 701reur-50 transmitters which work great with the exception of range failure at a couple of extreme locations on site. will the 794rEUR-00 antenna improve the range or do I need another piece of kit. please advise so I can order the correct parts. many thanks,

I would like to get the equivalent speech dialler but a digital one, Can you advise which speech dialler would be best?

I have changed the battery in my alarm, 9448+, the red tamper light is on and I am not able to extinguish it and reset the alarm