Intruder Alarms

Risco Vitron Glass Break Detector Tester https://www.securitywarehouse.co.uk/catalog/intruder-alarm-equipment-c-36/misc-detectors-c-36_84/risco-vitron-glass-break-detector-tester-p-1452.html ------------------------------------------------------ Have one of these in the garage, can it still be used ?

Hello, My question to you is, do you sell 868 or 433 Mhz. recevers and transmitters (detectors) of the risco gardtec eurosec CPX range. best regards, C.Boogaard

RISCO Group have a product update A new firmware update has been introduced to the Wisdom wireless control panel. The new version of the Wisdom firmware is V4.31, updated from V4.27 Why have we upgraded the WisDom panel The following fixes/updates have been modified to bring you an improved panel. Technical The panel has a new menu to show the connected BUS AGM IMEI number (Used for IP Receiver) The Blank Display has been updated in that you now only need to enter your code once. The

Hi, Our alarm has been giving us problems for about 2 weeks. It indicates an intermittent problem with the PA and low battery - the alarm goes off intermittently as well. we have changed the battery in the main control panel and the PA. We have inherited this system and have done nothing with it apart from keeping the PA to hand (and changing the batteries), it has never been armed. What advice can you give? We would be happy to disconnect the thing and switch it off completely - but when I try (by removing the fuse) the outside alarm goes off. Please help - it is driving us nuts especially during the night when it goes off for no reason. One thing - this probl…

Can anyone tell me why & what the flashing light on my control panel means when it reads "RF problem"? thank you any info would be appreciated. My system is a wireless Scantronic 500r.

Hi I have bought a new remote fob for my Scantronic 500r+ alarm system. I have managed to get the system to "learn" the new remote but the new remote will not set my alarm. Can anyone help?

please i am wanting to buy the scantronic 55 system however i have some questions - does this have a phone out feature via sim card or by bt line if it is triggered. does this accept pir / door contacts that have been used for an optima honeywell hard wired system since it is an 'hybrid' system... so that i might replace the optima and buy the wireless pir as and when i can. essentially i need a wireless system for a domestic use where i would have around 5 pir and couple of door contacts and smoke alarm external bell and key fob - is there anything other than the homelink 55 that is also suitable and fairly straightforward to use - set up and around

Can anyone offer advice on programming the advanced modes of this dialer? I want to enable the option that modifies the dial out sequence such that each of the 4 numbers are dialled once in turn (default mode is for No.1 to be dialled 15 times before moving to No.2) The operation/introduction section of the manual suggests that this option is available, however I can't find the appropriate advanced programming mode/code for this option. Any advice would be appreciated Regards and TIA John

A bit of a long reach this one, but I'm trying to 'emulate' a keypad for a Scantronic 8136 panel. I've got as far as identifying it using a 150bit protocol of what seems to be long and short pulses on the signal wire done through releasing the signal wire from ground and letting the panel pull it back up to +14v for a period of time 150 times synchronised by a clock. I'm hoping to build on this so that I can control my antique alarm system from my phone! Anyone have any further information on how this works, as my attempts to play back the pulses (I think) I've copied are ignored by the panel, so I'm missing something!

I have a Scantronic 9210 Intruder system with a flush fitting keypad in the lounge. I know this panel is obsolete but does anyone know of a panel that offers a flush fitting panel as an option if it dies. The wife's not to keen on a 6" x 9" hole left in the lounge wall $ I.m not keen to redecorate the lounge!!

Hi I am trying to download technical manual for the Scantronic 9448 from your website, is it possible for me to do that? We need to change a battery on one of these systems,and have ordered one from your company, on order no:xxxx. Any information would be useful. Best regards

Is the 9448 manual the same or similar to the 9448+ manual as I need to gain access to the panel without it going into full alarm. Or can anyone tell me how this can be done. I have installed many Optimas over the years but never got involved with Scantronic.

Good Afternoon We have a Scantronic 944ES intruder alarm system, but no manual. I would be very grateful if you could advise me if you are able to supply a manual for this particular model of alarm alternatively where we could get one from. Thank you in anticipation of your assistance Regards Lucy

Hi I recently purchased a communicator from ebay for my scantronic 9448+ panel. I thought it would be easy and it seems simple enough. I read the maunal and it says somethign about a lead being connected onto the board. I should be inside the backbox of the endstation but i dont have one. I spent

Is it necessary to solder in-line resistors to all the zone inputs i.e. E/E, PIR and door contacts? With my old Scantronic 9200 I just connected the contacts straight across the inputs on the PCB. The scematic shows a resistor on the e/e input. Thanks

Hello, My alarm panel has packed up so I'm replacing it. The bellbox has seen better days so replacing that as well. My original was a Scantronic 9448 so am going for the 9448EUR-90 control panel but can't decide which bellbox to go for. I'm stuck between Novagard 2 Merit , Ventcroft Compact Classic & Ventcroft Evolution. I want to know are they all compatable with my alarm system and which are reccomended? Thanks

Hi All, Fitted my new Scantronic 9448EUR-90 alarm panel. Everything fine. I now want to incorporate a smoke detector into the system(on the landing). Could you please advise me which of your detectors will work with my panel. Thanks, Stevec

Does anyone know how many PIR's can be connected in series together in one zone of Scantronic 9448EUR-90?

I am trying to install Scantronic 9448EUR-90 board with two Takex MS100E multi pattern sensors connected in series on Zone 2 (all other zones are disabled) and Elmdene Quartz 1000live sounder. My problem is that control panel shows temper fault - all boxes are closed, all cable connections verified. If I reset the panel by disconnecting battery and main supply the temper light will go off Zone 2 light will go on and when you try to set the alarm with users code the temper lights come up on again. Could somebody recommend how I can solved the problem?

I have just moved into a house in Windsor that has a Scantronic 9454 system. The previous owner left the manual, but no other information about the system. Can you tell me whether Scantronics is still in business? If they are not, has anyone taken over servicing their installations? If so, would it be possible to arrange an engineer to visit to reset the system and enable us to use it. Hope you can help.

Hi. Does anybody know what the bell/strobe output is on this unit. I am changing a Scantronic 9200 control panel and don't want to have to buy a new bell unit. A link to a installation wiring diagram would be good! Thanks

Hello I'm hoping to replace my existing intruder alarm panel with the Scantronic 9561 series panel. I do see that securitywarehouse is selling both the EN, and UK models of 9561. Now I know that 9561EN is a grade 2 alarm, and that 9561UK is ungraded. Are there any other differences in the two? Basically my question boils down to: Which one of the two should I go for, considering the fact that its going to be DIY installation, so do I need the EN model? Is the UK model flushed with older software in comparison to the EN model? Why is the 9561UK slightly more expensive than the 9561EU, even though the EU model is graded, whereas the UK model is not? Tha…

I have a 9600 alarm installed and need to relocate the keypad, problem being the keypad is on a under stairs wall and the internal bell box is directly behind the keypad on the inside of the wall, the wire between the 2 is about 3” long, can I disconnect the bell? Move the keypad and reconnect the bell, I know the tamper will go off but will it be ok to just put the code in when it does go off ? thanks Tony

Hello all I am in need of ome help please. My alarm has had it's first fault in 15 years by showing a mains failiure on the keypad. I have traced the fault and found that the power supply/transformer is knackered. 240 is going in but nowt coming out. Does anyone know if it's possible to get replacement power supply/transformers and if so where from. Cheers all. PB

Does the Scantronic 9651 EN-43 have a proximity remote keypad, if so does it come with any proximity tags included? Thanks