Intruder Alarms

https://www.securitywarehouse.co.uk/catalog/intruder-alarm-equipment-c-36/intruder-alarm-ancillaries-c-36_46/secware-ps7-adegen4-prox-tag-pack-5-p-5862.html Hello , I have the ade simple set unit, with the older fobs, which I can see are obsolete now. Your alternative link takes me to these items. Can I check that they work directly, or do I need to change the simple set proximity unit ?

Hello Questions about your kit refered: Visonic-Quick2Fit -Does the panel include the battery (should not, which reference to order). -Same question for the external siren -I can't find any reference for PIR detector from VISIONIC in your catalogue, so don't know which one from your catalogue could be compatible with the panel. Could you please advise (for pet tolerant only). Thanks

You have 2 items listed on your web site from Texecom. TEX-CGC-0001 which is listed as a Speech and Text Dialler at

Do you have a door contact sensor that links to a key/code box to turn the alarm off when door is opened? It’ll be used on an outdoor shed/container?

Please could you give me some advice on a wired alarm system to replace the aging Scantronic 808 system fitted to our house. I am a chartered electrical engineer, used to complex programmable industrial control equipment so will self install. The basic spec is:- 5 off existing PIR

I have a 15 year old Eurosec system that I whish to refurbish/upgrade. A few questions: I have what looks like the CP8L remote pad - is there an better option to replace? Tag compatible? Would you advise replacing the main panel at 15yrs old? I wish to add another remote keypad (garage entrance) and a contact/PIR - best option (remote tag?) Can you recommend replacement PIRs? Is there such a thing as wireless door contact?

Hi, I have installed my first wireless le sucre PIR on my flex system. Everything went ok with pairing until next morning I get keypad message rf batlow. Result: I am on my 3rd battery in 3 days!! So I have changed old PIR removed serial and paired new PIR with the panel and I can see the new serial No. in th RF intruder zone (signal strength is good menu 21). When I do a walk test I get no result from the RF zone. If I activate tamper the panel registers it. When I walk pass the sensor I get 2 long flashes then when I move after that I just get 2 short flashes. I thougth that wireless PIRs do not flash after warm up unless the alarm is set? The PIR does this wethe…

Hi. Does anybody know what the bell/strobe output is on this unit. I am changing a Scantronic 9200 control panel and don't want to have to buy a new bell unit. A link to a installation wiring diagram would be good! Thanks

Hi, Could you please confirm if the following batteries are suitable for the Optima Compact Gen4 and if they will fit into the enclosure ok? They are both made by Yuasa but one is cheaper, so what's the difference and which is the better one? http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=350 or this: http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=1339 Also, could you please confirm if you have both the Optima compact in stock and either of the above two batteries? Finally, if I order today, when can I expect delivery? Thank you

Hi, I installed risco cpx with novaguard 2 years ago, would anyone know what onboard battery (nimh I dthink)oes novaguard 6 comes with?is it 6v or 8.4 volts?my cpx panel is asking me this. The reason I am asking is because in logs I get Nov 1 chg(ma) Hi and Nov 1 on-chg Hi even though all the parameters are correct,not sure if this could be to do with me not setting the correct battery volts. the error in logs have been there since day 1 but last last I had a false alarm and in log it said " external bell tamper" and I want to just rule the volt setting out. Thanks

Looking for a shock sensor. I have an isolated gantry with access stairway. Trying to identify if there is a shock sensor / virbration sensor that can be placed on the metal structure that will send alarm when detection noted. Do you have a device that will perform in this manner

I have a GC Simon wireless alarm system (model: 60-911-010-4-IE) and one of my door sensors has developed a problem and needs to be replaced. However I am having great difficulty in sourcing a suitable replacement. I did by a recommended replacement from the USA but this did not work. I think because the system I have is 433Mhz and the new sensor was 319Mhz. Can you recommend a replacement sensor and where I may purchase same. Thanks in advance and regards

My new house was pre-wired for a hard wired alarm which I planned to fit myself. The guy who run the cabling did a good job except he did not wire for contacts on the doors. There is no chance to wire them now as I cannot run cables thrugh the dry wall panels. My solution I think is something like a Homelink 55 I will have 6 PIR, three door contacts, and two RKP's as I have a point upstairs for night setting the system. Can I add a second 9943 RKP to the Homelink 55 ? The Homelink 55 has 6 wired zones which would cover the PIR's. I hope I could use wireless contacts for the rest. Prox tags would also be a nice addition. Grateful for any advic…

I have a Simon3 alarm 433mhz and was wondering if your advertised sensor (Risco wisdom wireless door sensor 433mhz sensor)will work as a replacement and should the simon3 alarm learn this new sensor?

My keypad has given up the ghost with some butons not working so I cannot disable the alarm with the code. I've taken off the keypad and it has 4 wires connected. It looks very simple to replace so is it simply a case of buying a replacement and installing in the same manner? When I reconnect the power and the alarm starts going, I should be able to enter my code and all is back to normal? Or is it more complicated than that? I've been quoted for a replacment & fitting but it seems such a simple job to do yourself. Do I need to be aware of anything else?

Please can you clarify whether it is possible to have the Receiver and the Transmitter running on/from different power supplies. We have asituation where the alarm power supply cannot be supplied to the transmitter but can be to the receiver, so in theory it will function. If it is possible, do you have such a power supply - we assume a plug in transformer will do.

I have concept 6 alarm panel with a remote keypad that is starting to go faulty.do you have a compatible ADE keypad that I can replace it with.

Want to install a new Texecom Wired Alarm system with following requirements: 15 of Texecom IMPAQPlus With Built in Contact 10 of Texecom IMPAQPlus 1 of Exodus FT90 1 of Motion detector - ceiling mounted 1 of glass break detectors 1 of external siren 1 of internal siren 1 metal control box. 1 of external keypads 1 of GSM dialer 5 of Fobs Can you please suggest the best control box and external keypads and dialer?

I have an optima gene4(8EP396A) I want to install a remote keypad can I use a optima lcd (8EP417A) with this panel or do I have to use an led keypad.Please can you instruct what is best to use with this panel.

I purchased the above from you as a replacement for one in which some of the pressure pads are not working. When installed, will the new unit retain my original 4 digit code?

Can you tell me if I were to buy 2 or 3 different system PIR's would they all work in any alarm system. I have a system fitted that requires additional PIR units for more protection. I have had a home security police team look over my house. I would be grateful for any advice on this matter.

I have just orderd a ADE Optima gen4 8 zone from you. It will replace a c&k Active 5. I have the Engineers code for engineering mode. The problem is I can not stop the bell box from sounding when I disconect the bell wiring or when I try to open the bell box. The bell box was fitted and suppled by Abacus and is about 3 years old. I hope you can advise . Kind regards

Hi I have a ADE Honeywell Accenta Mini Gen4 with 4 bosch pir

I have an old, but fully functional wired system. It is an Accenta G8 panel. I want to add a zone using a wireless PIR I have seen the Texecom compact W-series on your website. Does this come with a receiver that wires into the existing panel? Will it work with my existing panel??

Hi I am stuck with looking at the diagrams to wire up ressistors for the alarm. I have bought flush door magnets with out resistors. Could you send me a picture or diagram how to wire up Double pole EOL resisstors for the Texecom Premier 48 panel? i bought the honewell EMPS-75 w magnetic contacts.