Intruder Alarms

Hi, Will I have any compatibility problems if I buy the controlpanel (powermax+ or powermax pro) from sweden and all the sensors from UK? I would like to have the speech and text in swedish. Could I even mix my setup with sensors from sweden and UK? Does any of the powermax(+/pro/complete) controlpanels support swedish language? regards Olof

I have recently changed a Optima compact Gen 4 panel as a favour for someone. The first panel that was bought through Amazon had a fault on it. A second unit has since been fitted and all is working except the new Siren which is a Reson 8. The unit comes with pre-fitted links across TA TAMP and PA. The manual states that these should be in place when powering the unit up. This contradicts some advice on online instruction that says to remove the link to T A when wiring the siren. The external siren does not sound or flash when an alarm is activated, internal sounder in board works OK and all zones work fine on a walk test. No LED,s in the siren are vi…

Hi! Bought a Visonic Powermax+ alarm from you and have run into some problems regarding master installer code and installer code. The problems shows on both the central unit and the keypad unit. When I installed the alarm, I (of course) changed the default codes to my own. However, as far as I can remember I only changed 2 codes where off one being the user code and the other one either the master installer or the installer code. Now I can't seem to access the alarm using the other alternative of installer codes. I would be glad if you could give me some hints to where I've gone wrong. The setting and fault behavior right now are as follows: 1. When first changi…

HI I recently purchased a Menvier SD3 order number 3122 and have been having issues with it reporting 'line fail' I have checked the sim is ok by using it in my own phone and have tried another sim from another network. The aerial is undamaged but i cant get this to work. Am i missing something basic. Barry

Hi. After installing a new accenta mini today i was ready to power up. connected mains but on connecting battery connections i saw the battery fuse blow. I checked all wiring, found to be correct and changed the fuse, connected battery and again the fuse blew immediately. I then disconnected all wiring from the system, i.e. bells and detectors, so it was 'as arrived new' and again, replaced battery fuse, powered mains and connected battery and the same thing happened again. I left battery & fuse out and powered up from mains. Alarm seemed to be working ok but i then noticed smoke coming from a resistor above and slightly right to the battery fuse, so i…

I order and received your Secware Optima 4 x PIR Kit and a Honeywell ADE Informa Speech Dialler. The kit content description on your site is: 1 x Honeywell Optima Gen4 Mini Control Panel (8EP396A) 4 x Crow Swan 18m Value PIR's 1 x Ventcroft Evolution SAB and Cover (Blue Strobe) 1 x 100m 6 core Intruder Alarm Cable 1 x Secware Value 2.1 A/h Battery 1 x Surface Door Contact I actually received an Optima Gen 4 Compact Control Panel won

Hi my home has been fitted with a scantronic 9651 system, it has p.i.rs in all down stairs rooms. The front and rear doors have surface mounted contacts. When I set the system and leave via my front door the alarm continues to beep and will not arm once I close the door. This has happened before and I was advised to replace the door contact which i did, this solved the problem until now! The same thing has happened again I have checked the contact and everything seems to be OK with no loose wires. The contact is grade 2 with a small circuit board inside, it also has a small spring tamper mechanism. Can anyone help? regards Steve

Subject says it all really: I've installed a Scantronic 9651EN-43 into an existing "wired" house and extended the system using the Visonic MCT-302/MCR-308R wireless system. I've linked the Visonic zone output into the 9651 zones and also linked the anti-tamper into the main loop as well. The Visonic can send a low battery warning and I need some suggestions as to how the 9651 can handle this? Obviously, it needs to bring the warning to the home owner's attention, but it can't prevent setting the system or set off a full-blown alarm if it occurs whilst the system is set. Many thanks for your assistance!

TXI Outdoor Curtain DetectorThe TXI is the world’s first high-mount curtain detector featuring patent-pending Triple AND Logic, delivering stable and accurate intrusion detection across the entire coverage area. Designed in a compact form, it provides reliable performance even in harsh outdoor environments, with true pet tolerance for real-world reliability. Compact Design with Advanced IntelligenceSmall in size but powerful in performance, the TXI is a discreet, high-mounted outdoor detector ideal for residential properties where appearance matters. Its sleek design blends seamlessly into building exteriors, while advanced detection technology operates in the background …

Hi I have an accenta mini g4 hard wired 4 PIR and exit door magnet my panel shows unset when I enter my code zones 1 6 7 8 light up and I have to omit these zones and press the tick to set the alarm which means the entry/exit is omitted I do not have any tamper wires connected to the PIR or door or the panel the only tampers that operate are the bell box and panel cover. the alarm works fine when the zones are omitted Can anyone tell me why zone 1 keeps lighting up and showing alarmed as this is the entry/exit please help!

Hello. I

Have Risco removed the ability to show the status on the LCD keypad? I've made sure that the Keypad is installed onto the system, but when I go into the Programming Custom Screens menu, It shows LCD Status = None. When I say NO, it just moves on to LED Status, and doesn't give me the option to change the setting to Full (for status always on) or Set/Unset which it always used to!! Is there another setting I need to alter first before I'm allowed to change the "display the status" setting?? Any help appreciated

Hello, Need a little help how to program different user and allocated zones for Veritas exel panel. Cannot understand the manual fully. Fitted 2 keypad and 1 panel. Keypads fitted to 2 seperate rooms. 1st room Main using door contact ..entry/exit and pir on zone 2 inhibit and zone 3 guard to cupboard contact. 3 users for this room + cleaner. 2nd room using zone 4 programmed as entry/exit. Have set all users their access 4 digit code and ok. How do I program 2nd room user zone 4 his own zone to arm and disarm without effecting the other room/zones on full arm. And 1st room programs not to effect room 2 Your help would be greatly appriciated. …

Hi everyone. I have been reading a lot of your helpful comments on various wireless alarms[ in particular]. as you will have gathered by by nom de plume I do not know a lot about these items. My questions are, in the scantronic range is the 703r contact transmitter for hard wiring in garage block to signal back to main panel in residence by wireless and are the 2 wired relay outputs suitable for external sounders [ sab]or do I have to use a conversion panel as on sapphire website. john

Hi! I bought a Visonic Powermax Plus last week (Thanks SecurityWarehouse !) 1. Is it possible to change Visonic Powermax Plus language ? 2. I've got two balconies : o 2 m x 3 m o 2 m x 6 m What is the best wireless protection for this balconies ? New Optex FTN-R/FTN-RAM ? Do you have other solutions ? Thanks, Jose.

i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the external sounder immediately going off?any advice on how i can fix this please?

check outputs? can anyone help me make sure i set it up right and what to check/fix i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the extern…

Hi Does anybody know if the external sounder in the Pyronix Enforcer Kit3, ENF/KIT3-UK, needs a power supply? It looks as though it is just battery powered from the description. I know some of the other Pyronix sounders require power when they are lit after dark. Can anyone confirm please? Thanks

Hi, Can anyone help. I have an Pyronix Enforcer alarm, all I want to do is edit Zone B. It currently sets downstairs in house and garage, I just want to edit it to set garage only, but can't find anything in the manual to help me do this, any help much appreciated, regards

Hi, I've never actually used one of these systems before but I've got a work colleague that's recently purchased one from yourself s. three quick questions 1. Is there a cheaper alternative third party keyfob that is compatible with this system that will talk with it, I'm guessing it's probably the same as a Honeywell galaxy g2-20, or visonic powermax where you have to use the manufacture branded keyfobs? 2. If they purchased the WIFI module I understand there's apps available to monitor and control the system remotely but could they also use the apps available for there phone so it works in the same way the keyfobs do?, would this include a simple set/unset …

Hi all, purchased this from security warehouse last year and just got round to installing it. I have wired up all sensors - 3 Pir`s and 1 door contact. I have an 16ohm external speaker connected to the system I have 1 Keypad connected to the system. 1 have one Lan card connected. I turned it on for the first time and i hear a time which confirms it has been turned on. I expect the keypad to light up but there is nothing from the keypad. The keypad does not light up. I have read if i hold down the D key it allows you to select the address and there is no response from either the one supplied with the system or the flush keypad i purchase addition…

Can someone tell me if the Pyronix KX10DP from SecurityWarehouse does work also in The Netherlands? Need 5 pcs. thnx!!

I want to purchase 5x Pyronix KX10DP from SecurityWarehouse. But can I use them here in The Netherlands? Are they compatible with the ones sold here?

Hi, wonder if anyone can help. I have a Pyronix sterling10 Panel and RKP and i am changing the bell box for a Gardtec Eurosec XS3D (the triangular one) i have wiring diagrams for both but i an unsure which wires go to where ...Could anyone enlightem me?? ...ie i.e ST- on bell box to NO on panel, TMPR on bellbox to BElLL- on panel etc.. Please help... regards//Martin.

Hello, I've just unpacked my second Sterling 10 remote LCD keypad, and found out that the little spring on the tamper switch is missing ( order 19838 ). this causes continue "Tamper" alarm on my central unit. Is it possible to send me a spare spring? Best regards, Robert.