Intruder Alarms

My system is now indicating \"trouble\"...\"AC failure...fuse failure\" The ac is connected and the supply is good. the manual says the powermax has 2 internal fuses that automatically reset. But still the trouble message is there. I am assuming its now running on the battery and will be dead within the next day. please help.

I'm currently self-building a house and am trying to decide on the alarm system (wired v wireless primarily) We have a pet (uses ground floor only) so PIR may be an issue. There are 3 doors (entrance, back and bi-fold) and 9 ground floor windows, plus 2 upstairs by a flat roof. I think I'd prefer wireless if possible, but I have a detached garage with games room above (1.5m from house). I also like the Texecom flush control panel - can you connect 2 of these? Can you recommend a system please?

Looking at Eaton 703R with Receiver and way to alert when received

I am currently designing system for my home.System will include fire detection. I require help with some of the system before placing order. 1. The panel I have selected is the Menvier TS590 which you sell complete with keypad. I would like to use prox tags with this system. Can you advise if the keypad will take the TSNET proxtr1 reader plugin? 2. Can you advise if you have in your reange carbon monoxide gas detectors which can be used with the alarm panel. I know that cooper produce one fopr their wireless system? 3. Do you have within your PIR detector range a 360 degree detector which is pet friendly? I could not find one when searching. 4. can you adv…

Currently speech dialler used to inform of movement from CCTV through text. View CCTV from iphone and would like to communicate via loud speaker to intruder. What products do you suggest, and how to connect.

Hi, I'm an installer looking for a 6 zone wired panel with option to expand using app, What do you suggest?

Hi, I am looking at the above kit to add 1 wireless door contact and 1/2 wireless PIR's to my existing wired system. Does anyone know how the unit is powered ? I think it's 12v but is this via a plug in transformer or does this somehow get it's power from an existing panel ? Also what frequency is this, is it 433 or 866 Mhz. Thanks George

I wish to order the following, can you help me ? 1x Texecom R8 plus + battery 3x Keypad (normal, no lcd) 1x indepedent Bell for inside + battery 1x indepedent Bell for outside + battery 2x Heat detector + shipping to France Thank you, very much (No need of PT wise i have already in stock ) Well, So i have 2 questions : i don't find any bell that are independant with battery, can you tell me a reference for one outside and inside ? For heat sensor, do i need RELAY version or not ?

Can you provide visonic power master magnets to compliment the visonic shock/vibration sensor making it a shock/contact sensor?

I have the above alarm unit & have been told that I need new PIR detectors. please can you give me a quote as to how much the PIR's are for the above unit.. PIR type 433. thanks

I am assembling the individual components of the Optima 4 kit minus the SAB strobe. I am substituting the Odyssey 3E, as I already have the diamond shaped cover. I have found all the components but not an exact match for 2.1Ah battery and surface door contact - could you advise which battery model and which surface contact model I should order?

i am having a problem with a gardtec 370 panel ,when i come out of engineers mode,i have an internal sounder, and the figure 66 shows on the key pad display,can anyone please tell me what this is.

Hi. I'm trying to find a light beam sensor to work on a driveway, to send a signal to my house when a vehicle or person breaks the beam. Can be hard-wired or wireless - the location is about 120m from the house - the back entrance to a farm. I think you must do such devices but I can't see them online.

Hello, I have a Scantronic system consisting of a 9448 end station and 9427 RKP. I wish to add a further RKP and the only RKP apparently available is 9427EUR-80. Is this suitable?

Do you have a wall mounted Pir covering more than 120 degrees? Like GE's Sharpshooter

We have Optex FX-59 QZ alarm system which now it says to replace batteries however there are no batteries inside the sensors and in the panel. What are we supposed to do in this case? The alarm went off and an orange light keeps flashing.

Have Gardtec 350 panel which requires a closed tamper circuit. Can you please suggest a suitable relay to use with the mcr-304 to give a NC output.

hello, could you tell me what frequency your texecom intelligent keyfobs are? I have an 868mhz intelligent receiver and i want to make sure they match. thankyou sanj

texecom prestige ir would that work with texecom excel.does it depend on eol of the control panel and the pir to work together.

Dear Sir, I am looking for a wireless intrution alarm for a family house. I would like to have features such as, remote control frorm android or ios, GSM, camera display remotely. I live in Sweden and the alarm needs to support the EU standards so that it can be connected to a local security service if the alarm goes off. Would you recommend an Kit?

I have an old ADE Ultimate (using id biscuit) Burglar alarm system. Purchased in 1993. The remote keypads are playing up. Do you have replacement remote keypads for this system or can you suggest compatible remote keypads for this system? Thanks.

My existing panel was faulty so I puchased a Risco Gartec 490x from you. I liked it beacuse it is hybrid wireless and we are having an extension built, which will make it easy to add additional movement detectors. The control panel and keypad are installed and work fine apart from one problem. I get a warning - off chg volts high / battery/fuse fault - it takes a about 30 minutes after exiting the engineer mode for the fault to register. Its a new battery (again purchased from you) and the fuses are all Ok - any ideas what I have done wrong. Also given that I am not a registered installer will Risco technical help talk to me or am I on my own. regards

I have lost the manual that came with the Accenta 6 when it was installed some years ago. The Alarm is still functioning perfectly. Is it possible to obtain a new manual?

I have installed, approx 9 years ago, a scantronic 500r.+ system and have had the remote control stolen during a break in. My fear is they will return. Is it possible replace the control box with a new one in order to make the remote U/S, Or is it possible to disable the remote. I have 4 PIRs one door sensor and a remote key pad. Sorry I have marked this high but having just lost a new car do not wish then to re-visit disble the alarm and clear the rest of the house. Thank you for your time.

Can you tell me what wireless portal is required for the galaxy dimension 520. Thank you.