Intruder Alarms

I am trying to buy 25 pieces of the Yuasa NP7-12 buy your system restricts to only 5. Can you help?

I want to use 12volt bells as my warning devices but I've been told that they will burn out the microprocessors on modern control panels. Is this just a way for the trade installer to put me off doing it myself or is there any truth in what he's saying.

Galaxy RSS software and Management Suite. Wants to know the difference.

o whom it may concern I was looking through you web side regarding the Honeywell Model G2K3WR-01-Cand i would like to ask the following question 1 when system set off I;m able to set t to call the police station and other numbers? and should be connected with GSM or landline? 2 I'm able to connect wireless movement detectors and wired detectors at the same time? 3 the system will be provided with installation manual and user manual? if the above not possible, could you please guide to the another Model with allows the above. hope to hear from you soon Thanks & Regards

I am interested in purchasing the Honeywell galaxy flex FX020 with a Mk7 keypad but have a few questions first. 1. Is the Honeywell reson8 bell box compatible with the above panel? 2. Is the Honeywell AG3 bell box compatible with the above panel? 3. Does the alarm panel come with the 680 ohm resistors for EOL wiring to the keypads? 4. Does the alarm panel come with the 1k and 2k resistors for double balanced wiring to the PIRs? 5. Does the rio zone expander come with the necessary resistors like the main panel for the additional zones? 6. Does the rio zone expander get its power from the main panel? 7. Can both the gsm/GPRS module and the Ethernet module both fi…

I need to add an additional control panel to my alarm system. The current panel is menvier ts700. Do have one which will be compatible with this or would you recommend installing 2 new control panels and if which ones please?

Hi, i'm looking to buy a wireless digital alarm system with at least 16 zones. i'll also need the contacts and pirs etc to go with it. Can you help?

Hi, I purchased a Scantronic 9651 from you in July. I have now noticed that in Eng Mode all IR and Panel tampers are taken out (as expected) allowing me to access the components, but having just taken the external siren cover off the bell rang immediately. It may be that this is correct but I was not expecting this (other panels I have installed eliminate all tampers in Eng Mode, inc the Bell). I would appreciate it if you could advice me if this is correct. Also, if it is correct is there a way to avoid the bell going off during maintenance of the system. For your info I have fitted a Pyronix Belle to the 9651 panel as below. Belle 9651 B- 0v B+ 12v BA OP1 (Bell) STB O…

Hi, I am about to move into a 200m² 4 bedroom detached house in the countryside, I've never had an alarm at a house before, but my wife is worried that as this is more isolated than previous houses (nearest house is ~100m away), that we are at a higher risk than our previous central village location. I am intending on a DIY install, I'm reasonably confident at my capabilities in laying & connecting wiring and drilling holes and am a computer programmer by trade, so would hope the programming side wouldn't beat me! After quite a lot of research I think I've settled on the Honeywell Flex 20. As the whole house needs decorating, I'm not really looking for a pri…

Do you have any motion sensors with two contact sets ? So that it is possible to use one contact for alarm, and one for home automation ?

I HAVE A RISCO ALARM FITTED WHICH CAN BE ACTIVATED REMOTELY, I AM GOING TO BUY THE RISCO 4 BUTTON REMOTE FOBS, DOES ANYONE KNOW IF THEY COME WITH PROGRAMMING INSTRUCTIONS ? OR IF NOT DOES ANYONE KNOW HOW TO PROGRAMME THEM TO MY SYSTEM ? THANKS

I'm just inquiring about your Klaxon h series burglar alarm sounded, just wanted to know is it compatible with a Honeywell accenta control panel and also is the sounder the same as shown its the picture?

Hello again I've recently come across a fault with the above type of detector. I seem to be getting either the sensor false firing or possible emc problems. I've lowered the sensitivity with the internal jumper but the fault is still present, all connections and continuity through cable seems to be good this is why I'm now thinking it could be emc. If it is emc does anyone know of a cure that doesn't involve re-running of cable. Thanks in advance for any suggestions.

I would like to order some Bosch Blue Line ISM-BLD1 TriTech Blueline Detector. These are available in three frequencies. I'm interested in the 10.525 GHz ISM-BLD1- F1 model. Would you able to supply this model ?

I'm looking for a domestic alarm that supports 2 zones (one hardwired (ground floor) with 4 PIRs, one wireless (first floor) with 3 or 4 PIRs) + 2 keypads + keyfobs + a control panel that can dial out (PSTN or other). What can you recommend which is good value for money?

Hi All First time poster..... I am looking to install an alarm system into my office with the following components:- Could someone recommend specific part number for items below ? Many Thanks Regards M. A Glalaxy G3-48 grade 3 panel with integral monitored 1 amp power supply. An Ethernet module to be fitted in the control panel. A proximity keypad. Two combined infra red and microwave movement sensors. Two graded door entry surface contacts. A viper vibration sensor to fitted to two main entry doors. Two anti lift bolts for two main entry doors. Two 12v optical smoke detectors. A graded external siren with st…

Am i right in thinking the internal sounder should sound along with the external when the alarm is triggerd? since mine doesnt, all it seems to do is the chime facility. daniel

Hi I want to add a magnetic lock that released when the panel is unset. I see there are 2 outputs on the Premier 48 both that can take 1A but this seems alot. is it really ok to wire directly on to the pannel without needing a relay. Im thinking of running the SSP Mini Magnetic Lock unmonitored on the door conserned. if I do need a relay do you have a prepackaged one with power supply etc? Any help apprecated. Rob

I purchased a Powermax plus alarm system from yourselves 3.5 years ago. Has been working fine, but I seem to have lost the Master User code, I did change them from the default. It has been working perfectly but I now need to remove a sensor from the system. How can I reset the codes. I tried the jumper reset but this had no effect.

The systems re-starts itself making impossible to use is as it fires the alarms every time the systems re-starts. The system installation was installed about 2 weeks ago and at the beginning, about every day, at any time (middle of the night or right in the afternoon) the systems alarm was on but with NO intruder detection as the system was NOT armed. Watching the log events, every time that it fails, shows “START UP” and “MAINS OK” and the LCD Keypad shows new date and time as when start up for first time (like default factory data). With this information, I understand that power is being lost for some reason so I changed the main power supply connections just to make …

do you have an alarm kit that can be set on using the mobile phone? if yes send me the product code

Have Gardtec 350 panel which requires a closed tamper circuit. Can you please suggest a suitable relay to use with the mcr-304 to give a NC output.

Is the 9448 manual the same or similar to the 9448+ manual as I need to gain access to the panel without it going into full alarm. Or can anyone tell me how this can be done. I have installed many Optimas over the years but never got involved with Scantronic.

been looking at your honeywell accenta gen4 mini packs which include a control panel and lcd keypad,

Can you please advice me on what system i shall use? I'm out after an alarm system that has at least 3 zones (1 for intrusion, 1 for fire, 1 for water leakage) for a 2 story house, preferably which own output channels and which is possible to connect to the internet. Maybe for intrusion i should have 3 zones, like inside, perimeter and outside? Sensors i will need are: Burglary (movement - with windows breakage?), fire sensors and water leakage sensors to put in sensitive areas. I have been looking at the honeywell which seems good, but can you please give me some suggestions on good systems?