Intruder Alarms

I built my house 17 years ago with a wired alarm system. The six core wiring is inside the wall panels etc. Over the years I have replaced a couple of PIRs etc but now some of the other components are starting to fail (e.g. some parts of the LED displays do not show etc). I was looking to use the existing wiring and replace the control panel, two keypads and the external siren with the following: ADE Honeywell Accenta Mini Gen4 with LED Keypad Secware 12v 0.8A/h Value Alarm Battery (assuming the Mini Gen4 does not include a battery) ADE Honeywell LCD Keypad for Optima / Accenta Control Panels Honeywell ActiveGuard AG6 External Siren Blue. Inc White Cover Is this feasib…

Hi, So it's 1:49am, my husband is at work and I can't get hold of him. my 9800 alarm is saying battery fault and keeps going off every few minutes. My daughter is stood by the pin pad in tears whilst i desperately try to find a solution - is there anyone who can help? I feel sick and I'm shaking! I don't know if it's going off outside. The company who installed it have gone out of business and I don't know who to ring and there's no user manual anywhere, I can't find much online either. I'm in north Kent, any help would be so gratefully received. Thank you

can you let me know if the Honeywell activguard AG6 works with the Visonic powemax system that you sell.

Hi I'm interested in getting the Visonic Powermax+ Quickfit Kit (inc Wireless sounder). What Keypanel do you recommend? I assume it's recomended that you put the control panel in a closet or something and not close to the door? Also, can the whole kit run on battery only? if so, for how long? BR

Hi, Just wondering if the above is a straight swap, we have found a number of simple GL's on doors that would be somewhat better/safer with contacts, Many thanks, Mark

I have a Gardtec 800 system with an 8 way zone expander unit. After a lightening storm the panel comes up with a fault: LEX1 tamper. I believe this is a line expander unit fault. You are selling a Gardtec 02083 Zone expander unit - is this the same as the line expander unit I have (label with EX MO1/11 EN50131-1 PD 6662 G3 EC2 PR5705 Rev 1.0 4390) I would appreciate your help.

Hello, I have a Scantronic system consisting of a 9448 end station and 9427 RKP. I wish to add a further RKP and the only RKP apparently available is 9427EUR-80. Is this suitable?

About to connect my visonic powermax complete to the telephone. According to the picture in the manual its just to plug in. But theres just two small holes. The telecable dont have pins. What to do? I havnt seen such a cable before is it typical UK?

Hi there, I have a Securit 900c alarm panel and require a replacement keypad do you sell a keypad for this model, if so can you provide me with a cost and part number so that i can order one from you. many thanks....Tom

I require an alarm system that has the capability of giving 2 outputs to a relay to indicate Set/Unset and Alarm sounding. there is only a requirement for 4 zones (2 door contacts and 2 PIRS), an external bell box and we need 2 keypad i have been looking at the Texecom alarm systems as we are familiar with these. can you advise which model would give me the above requirements.

I have a Scantronic 9651 bought from you a few years ago. It's worked fine till the PA alarmed the other morning for no reason - i.e. it wasn't pressed. I put a new battery in it Feb 2014, probably the last time I opened it up. When I put the engineer's code in, in order to open up the PA to check it, rather than going into engineer mode it said "User code reqd". Odd?! Anyway, I then put the User Code in and it said "Set". This is not normal behaviour - any ideas? Thanks,

Please would you clarify if the "Honeywell Intellisense 800L 8 Zone LED Control Panel Honeywell Intellisense 800L 8 Zone LED Control Panel" at

For our site we are going to need an expander for another building to be on the same system. Can a partition (area) have zones from the main panel and the expander?

Texicom Premier Elite 24 panel, siren and medusa PIRs, Order Number: ***** 31st March and recently completed the installation hard wiring 5 PIR’s into each of 5 of the 8 zones available within the panel. I have set all 5 zones ‘double pole / EOL’ but the panel is showing tamper fault error message. Following further investigations it appears the medusa PIR require 2 resistors to be installed across the tamper 2k2 ohm and zone 4k7 ohm. My first question is – is this correct and secondly do you stock these items.

I have just purchased today from you this item could you let me know if it has an operating Frequency: 433MHz at 200KHz bandwidth

Hi, i had a Powermaster-10 kit installed about a year ago. Recently the ability arm via a SMS message (arm xxxx) has stopped working. Using SMS to ask the alarms status (status xxxx) works and when use the communications test option via the control pannel i get the Auto test SMS message sent to my phone. I've tried differnet pass codes for differnet users etc. Plenty of credit on the sim card. So all seems to be working except the ability to arm? Any thoughts or suggestions on what else to try/check. Thanks Ewan

hello i am looking for a alarm system which will protect my home and garage .also a cctv system with hard drive.thks adam

According to installation instructions for AG6 sounder PCB should be marked as follows TR- V- ST- V+ S- The actual PCB is marked ST- R- SW- V+ V- Can you confirm R- is actually TR- and SW- is actually S-

I moved into my current property and had an extension done to the building. As a result I haved added detectors (from SecurityWarehouse) to the alarm panel (Honeywell G2-12). However, when the alarm engineer attempted to access the menu, the code I was given was not working. Hence the engineer is locked out of the menu What is the best way to get into engineer menu and reprogramme the panel? any help would be appreciated?

Hi looking to fit logic 6 to my house and i need 5 pir i was looking at the bosch ones one of those is for my garage and 1 door contact. will this all work together or would recomend a diffrent control unit? hope to hear from you soon i would like to order today thaks Dan

Can anyone recomend an alarm system that will notify by text message for alarm triggers including set/unset (ie access to the premise) I currently mainly fit texecom products and have used voice diallers regularly but a client now wants that bit more! Any advice welcome Thanks

I have bourght quite a few of these & on wiring & checking them find none sound when tested. All you get is a constant lit LED. Is there a possiblity that all are faulty or has someone designed the ultimate pointless product? If one went into alarm I'd expect all linked alarms to sound. Is this not the case with all linked 12v linked detectors?

Only zones 1,4,5 used .zone 1 is the exit/entry zone .All PIR detectors work on walk test and zone 1 works in chime mode.The alarm sets OK system bleeping until set . when the entry zone ( 1 ) operates it goes straight to alarm , after reset code entered the panel has zone 1 flashing only.

I have problem where the dialer will dial out when made to do so through test setup/Engineer mode no problem but doesn't dial when the alarm is activated. Is this Informa faulty?

my customer has a accentra mini 8 alarm system, the external sounder appears to be faulty. Can you supply a replacemnt sounder. If so can i replace old with new wire for wire without instruction? The existing sounder has security alarm with a man climbing through a window logo on it. hope this helps?