Intruder Alarms

I successfully installed my SPC4320 with IR sensor and Elmdene ELM300 internal sounder. This configuration works properly today. I wanted to connect the external Rapier sounder but I have two issues: - Tamper detection: I wired the tamper on sounder as explained in the Rapier manual by choosing the 2.2K resistor on the board and connected it directly to the TR pin on the SPC4320 but the tamper remains faulty even if the sounder is closed and fixed (sensors on the Rapier work well as confirmed by beep from the sounder). - EX+ and EX- signals: In SPC Pro->Panel setting->Controller input and output->Output (please see attached screenshot), I try to commute the ext.…

Risco Gardtec KITCP8LG2 I've a problem with one of the central units. It isn’t possible to set the number of times the bell is capable of sounding during a set period. If the system is triggered, the bell sounds always, even the third, fourth, … time when the number of bell re-arms is set to two. I’ve already disconnected all the connections and made a factory reset, but it isn’t making a solution. Please can you help me?

can you supply extra PIRs to infinate wireless kit and at what price?

i am looking to buy control panel witch can accommodate 8 pir and auto dialer and i would also like to buy autodialer (speech dialer with at lease 5 numbers ) and if possible fob entry system with 4 key fob's

I have a couple of questions if anyone can assist please before I order. I am using 3 x tritechs in house (a little ott but for pet tolerance) - I also have a conservatory that gets very hot but will not have pets. Should I just use another tritech or would a DT7450 be better? Has anyone used the Texecom Odyssey 5 compact or is it best to stick with full size? I have 3 x M12 smoke alarms on 1 zone and my installer doesnt have much experience of fitting these when using resistors. He was going to check but can anyone advise what may be required else we will just wire the whole system with seperate tamper circuit. thanks

what would be the best P.I.R. for a warehouse that is full of hole, where the local Squires, Rats and a factory cat wonder free.

hello. can anyone please tell me wwhere i can get the software from for my laptop to be able to programme a Honeywell Galaxy Dimension GD-520C thanks

Hello again I've recently come across a fault with the above type of detector. I seem to be getting either the sensor false firing or possible emc problems. I've lowered the sensitivity with the internal jumper but the fault is still present, all connections and continuity through cable seems to be good this is why I'm now thinking it could be emc. If it is emc does anyone know of a cure that doesn't involve re-running of cable. Thanks in advance for any suggestions.

Hi, I am thinking about buying a Le Sucre alarm system. I am discouraged to buy a professionally installed system because of the high maintenance charges. Is the installation of the Le Sucre system straightforward enough for a member of the public to install? I have some technical knowledge so it would help if you could highlight any specific challenges. Many thanks.

Dear sirs, I'm about to order a complete Texecom hardwired alarm system and I would like some help. Firstly I already own and I have prepared the cavity on my aluminum doors/windows for this magnetic contacts (https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/door-contacts-switches-c-36_44/knightbiased-flush-pencil-single-reed-6core-4k72k2-brown-p-4544.html) My question to you is (by your knowledge) is there any chance of interfering with the aluminum material? Aluminum is not ferromagnetic but is paramagnetic metal. I would appreciate any input on this concern

I currently have a wireless Scantronic alarm system which I am hoping to service myself. Currently it is flashing for a new battery. Firstly are you able to provide a new battery for the control boxes? Secondly if I open the box I assume it will go into tamper mode, are you able to advise whether I can source an engineer code?

I have changed the battery in my alarm, 9448+, the red tamper light is on and I am not able to extinguish it and reset the alarm

Hi, I'm looking to install an alarm system on a static caravan in an owners only holiday park. I only plan to use internal sounders (quite possibly just concealed speakers in the roof space connected to the panel) as I don't plan on disturbing neighbours in the event of a *prolonged* power outage. These would be close enough to the external vent to be easily heard outside - but also uncomfortable internally and very difficult to access. I'm after advice with regards to the most suitable PIR sensor to use. I'm planning on using a dual tech variant, but need one with a decently adjustable microwave range. Could you recommend one? I'm currently swaying tow…

Can you tell me which firmware is loaded on this key please.

Good morning, Thank you for your email regarding the cover for my Flash Guard sounder. I am quite happy to purchase a new unit but would like to know if the six core cable that controlled the old unit will be ok for a new one. I have included a photo of the old unit and to which colour went to which connection on the vertical block located on the left of the photo. 1- Yellow (Tamp out) 2- White (Tamp in) 3- 4- Blue (Supply minus) 5- 6- Green (Trigger) 7- Red (Strobe plus) 8- Black (Trobe minus) There was then a Red coming from a battery going to the plus connection on the small terminal block. I hope this will help in recommending the right sounder for my application.

I need to install a Eurosec LCD RKP keypad to replace the existing keypad which is working but worn out (keys don't work very well). If I just remove the old one and connect the existing wiring to the equivalent connectors on the new one will everything just work as normal or will the system need to be reprogrammed?

Hi I need to install a system to protect a secure shed. I dont want to spend more than

I'm looking for a replacement for my Response SA5 which I have had installed from a previous property on a 'temporary' (5 years!) basis whilst I finish a self build house project. I now have around 16 separate, hard-wired door/window contacts and I want a new system that allows them to be individually monitored. On top of that, I'd like to have 6 or so wireless zones for possible future expansion eg garden shed etc. The next requirement is to have a built in voice dialer. Lastly, I want to be able to access the system via the internet in the event of an alarm so I can interact with it - switch it off, see which zone has been triggered etc. I already have s…

Hi, I recently purchased a new CPX alarm. I have programmed the alarm with multiple sensors and was attempting to test the set when I got the following message: please enter eng + anticode 4141 Can anyone help? Thanks, Darrin

Hi, Bit of a simple question here but does anyone know where the default code 1234 is stored in the users menu so I can change it to something different? Cheers Matt

will this alarm box be compatible with my avanti sytem.I have an MDT bell box which is no longer working, I have tried running a 12v supply to bypass the battery,the green/red lights come on, but no sounder. thanks https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/sounders-c-36_45/external-sounders-c-36_45_140/pyronix-deltabell-plus-external-sounder-back-plate-blue-p-2867.html

i need to replace 3 fire sensors at home that are compatible to my house alarm system. it is a sterling 10 by pyronix. i am told they have to be normally closed. can you recommend a sensor

Hello, im intrested in a vsonic kit with gsm module, does it have gsm already installed or its extra purchase. It should work on 868mhz. WHich one do you recomend with theese demands, kind regards

My Honeywell Optima Compact intruder alarm system, now 16 months old, is activating tamper alarms at random times, in both Day and Set modes. These reset straight away. I have linked out the panel terminals for both the sensor tamper loop and the remote LCD keypad tamper loop, which takes a wiring or tamper switch fault out of the equation. The tamper alarm still activates every couple of days (or nights .... it went off at three this morning!). Question; does this indicate a control panel hardware fault or a software fault? And if the panel is faulty, is it still under warranty?

Hi I'm looking to upgrade a Texecom Veritas r8 with pet PIR. Do you know if the following is compatible (Bosch Blue Line Gen 2 BLD2 Pet TriTech Blueline Detector ISC-BDL2-WP12H )