Intruder Alarms

Was wondering if you can supply a simple remote panel for the Optima Plus 2

I have purchased a Scantronic ion-40 control panel and a Pyronix Deltabell E, but I'm having a problem getting the bell to trigger. I have attempted to follow the wiring diagrams supplied with the panel and the bell, but they don't match up 100% and unfortunately I cannot seem to get the bell to trigger at all Deltabell Connections: T T ENG HOLD STB BELL +12V -12V ION-40 Panel Connections: AUX 0V AUX 12V OUTPUT 1: NO OUTPUT 1: C OUTPUT 1: NC OUTPUT 2: NO OUTPUT 2: C OUTPUT 2: NC TR

I am considering buying some honeywell equipment to upgrade my alarm to wireless. Firstly I just wanted to check that all the components are fully compatible with the Galaxy G2 panel (I have the G2-20, or actually the G2-12 as it is not expanded), and that it will support this many sensors. Do you know this for sure, or should I contact Honeywell directly Honeywell Wireless Door/window compact magnetic contact Honeywell Wireless Dualtec 15m x 18m Honeywell Wireless Smoke sensor with built-in sounder DF8M Honeywell Carbon Monoxide Wireless Detector Honeywell Galaxy 2 Series Wireless Receiver (RF Portal) Microtech Galaxy MK8 Keyprox LCD Keypad Honeywel…

I have motion detectors Next K9 PG2. They create false alarm due to small animal walking in the area, How can I configure in order to eliminate these false alarms?

Would like to know if the Visonic 33 kit is easy to install?

Tate T-B600 external sounder does not seem to be available anymore. Please advise on suitable replacement external sounder box for wired system to Tate "Javelin" 8 zone panel

Hi Folks, Looking to replace a failing alarm system we currently have in place at a county scout hut. It consists of three PIR's, auto dialar and the central panel/main box. The alarm is activated by locking he door and de-activated my unlocking the door! (Clever stuff ) For ease of use we'd like to keep this system. For numerous reasons we wont be using a control panel to type in the code! Any suggestions? Just looking for a replacement system.. Something that we can use the existing lock with! (The door lock is simply wired straight to the alarm) Regards, Scott

Hello I have a veritas control panel and key pad with a wired intruder alarm system. The power circuit tripped and now I have the \"unlock\" light flashing. Until this is sorted I cannot set my alarm. Can you help please. Regards Roger Bell

We're about to install an Accenta Mini Gen4 with conventional intruder detectors, remote keypads and an external bell sounder. We will also have a number of Menvier M12 smoke detectors on Zones 7 & 8 for 24-hour fire detection. If Zones 7 & 8 trigger, we're expecting the Accenta to display an appropriate alarm on the RKPs and do 2-sec on / 2-sec off signalling on the external bell box. If possible, we also wish to fit an all-in-one sounder / strobe unit in a specific room to ensure that the occupants understand that the "bells that they can hear ringing in the distance" are indicating a fire alarm (and that they should evacuate). We're uncertain if somethi…

Hi I wonder if someone could help me please.I have a Veritas R8 with 5 zones 2 keypads,2 panic Buttons.We went away for the weekend came home electric Had triped alarm had gone over to battery and flattened both alarm panel and bell box, I turned electric back on alarm powered up and recharged but both key pads won't do anything every button you press has the same tone it seems to have locked out.The battery seems ok because if I disconnect from mains it lasts ages.Is it time for a new panel? Thanks Guys Gary

These PIRs require a power supply of min. 9V which I intend to draw from the Powermaster Central 12V auxiliary output, as it is backed up by a battery. The PIRs consume 19mA max, so 38 mA in total, which exceeds the Powermaster specs of 36 mA max for this auxiliary output. Can you suggest an alternative power output please, or do you think it's no problem to connect the PIRs as planned to the Central.

I am looking at your product MCR-308 + RL8 on-line and just wanted to confirm the the item includes the relay module (RL8). I want to use the item to add wireless zones to an existing Scantronic 9651 system, could you confirm that this is suitable?

I installed an I-on40 and two keypads, KP-01. I had a problem earlier in the year whereby the keypads beep indicating 'Duplicate Entry.' I tried replacing the keypads with a spare, but this did not resolve the issue. I had thought that it might be caused by line termination, so I changed that. It worked for several months, with one terminated and the other unterminated, but the 'Duplicate Entry'; has returned. KP1 is located about 1 meter away from the I-on40; KP2 is located about 10 meters away. KP1 is set to address 4; KP2 to address 2. The error occurs whether I try setting or unsetting the I-on40 either manually, by typing in the code, or by using a fob.

Hi, I am going to upgrade my Galaxy G2-12 wired system to a wireless system. The list of components I think I need to purchase are in another thread where I was asking about compatibility :- http://www.securitywarehouse.co.uk/forums/topic/4414-ticket-question-wireless-peripherals-with-g2-12/ and are reposted here :- - Honeywell C079-2 RF Portal - Honeywell CP051-00-01 MK8 keyprox - Honeywell C072 Boxed RIO expander - 3x Honeywell TCC8M wireless keyfob - Honeywell SMB10 Motion sensor mounts - RS485 Bus wire : Twisted pair screen cable Belden 8723 equivalent - 680 Ohm resistors - 4x Honeywell DO8M - Door - 5x Honeywell IRPI8M - IR…

Can not connect to SPC connect with SPC 4320, ethernet works I've SPC 4320 with latest firmware 3.6.6. It is a completely new central and has never been connected SPC connect. From error messages it seems that spcconnect.com have problems, but Im not sure. Nice if someone can see if you enter the SPC connect today. If so, then the problem must be on My side. fine if you someone can look at the small details of the config and help with finding what I've done wrong. I have used the video below to double check my setup to connect SPC I can not run the registration of panel spcconnect, after I enter registeration ID and username password I get the message that "Can…

would the Siemens IMKW6-10 wireless contact work on a Europlex signet 200 alarm panel.?

I’m after 2 No. keypads compatible with the 4 wire Gardtec 600 or can you recommend a compatible alternative.

I have optima MX6 old model of burger alarm system which is faulty and looking for update alarm control panel only. I would like to keep original IR sensor, alarm bell, contact switch and panick buttom if possible. Please could you kindly recommended the model number for my replacement and actual cost. Jimmy

Does the Scantronic 9651 EN-43 have a proximity remote keypad, if so does it come with any proximity tags included? Thanks

I have a Eurosec CP8L LCD. This has been very reliable. However I have had a new front door fitted which meant using a new surface mounted reed sensor for my entry/Exit contact wired in series with my back door sensor. I want to check my zone settings. I want to reset my entry time to 30secs, unfortunately I am unable to programme the zones, the display just keeps going back to "do you want to Program Chime" and will not allow me to proceed further to Program Zones. Have you any idea how I can get to the program zones. I have done a factory reset, ie:- disconnected the power, etc but to no avail. Have I pressed something I shouldn't have? I have had …

i would like to ask if the auxilliary input of the MC-302E PG2 can be programmed as a different zone.I want to use 2 different zones from the MC-320E PG2. Can this be done ?

Please could you advice on the best Honeywell Home Wireless Alarm System which will allow notifications of activations to be sent to mobile phones and allow interaction by mobile phone I was looking at a price range around &300 to £500 is there any systems in or around my budget?

Hi, Please can you recommend a smoke alarm suitable for connection to a texecom premier elite that is good for a garage/workshop area? I'm guessing (given use of angle grinders, woodworking equipment, etc) an optical alarm is not a good idea. The garage is also poorly sealed (large gaps around the door) so does get very cold in the winter. I was wondering about the Texecom Exodus RR/4W. It seems to be recommended for places where temperature won't exceed 38C, which sounds likely for my garage. Would it be a good choice? Thanks Joseph

Good Afternoon We have a Scantronic 944ES intruder alarm system, but no manual. I would be very grateful if you could advise me if you are able to supply a manual for this particular model of alarm alternatively where we could get one from. Thank you in anticipation of your assistance Regards Lucy

I Think that I require, Control panel (can be hidden under stairs) 1-off Nice looking Lcd keypad (for front door) 1-off keypad (for rear door) 3-off wired Quad PIR for inside 2-off wired Dual tech PIR for outhouse (extreme cold/heat). 3-off internal Door contacts. 1-off garage Door contacts. Panic Button Txt or voice dialler Listen in function Dial in to arm/disarm would be nice or over web via phone? It would be good if the alarm had wired and wireless zones in case I need to upgrade after the floors went down I really like the Honeywell Galaxy Dimension GD-48C with Touchsceen Keypad Kit, but is it over kill? What would you get? Thanks in advance…