Intruder Alarms

I just tried to purchase a GUARDALL W74065 M2 (W74065) IR detector, but the order was cancelled because the item is out of stock. I need to purchase a replacement for a faulty Guardall Apollo IR detector. Can you suggest a suitable replacement?

I purchased a Meniver SD2 from you a while ago and have just got round to fitting it but it isn't working and I'd like some help to get it work. I have wired the autodialer into an alarm system and all appears to be good until the unit goes to dial out. I have run test facility and the unit opens the line and then dials, it's says on the screen wiring to dial. I can hear a dial tone before the dialling but the call does not connect. Then before you can hear any connection to the dialled number the unit starts to send out the recorded message after a few seconds. The line test on the unit shows that the line is ok and the fact that a dial tone can be heard before it dials…

Eurosec CPX Panel & LCD KP, I have a site with wired detectors/door contacts/sounder + 2/3 wireless detectors so was thinking of this panel. What wireless PIR's/Door Contacts will suit and is there anything else u require for the wireless PIR's/Door Contact to communicate with the CPX, or is the CPX all set up to accept wirelss detectors ? What about the G-Tag, is this already built in to the KPads, so all u require are the Keyfobs ? Scantronic Homelink 55 Hybrid with LCD KP - as above basically, can u mix Wired/Wireless detectors etc. thx Mark.

Hello I'm after 3 off Elmdene Panic Buttons, model ELM-PA-G3-W Would securitywarehouse supply these (not current listed stock) , or can you recommend somewhere. Thanks

Hello. Interested in installing an alarm system. Such as Electronics Line Infinite Wireless Kit can you tell me if i can change options and replace the PIRs for Door Connectors? Does the external box sound and is this wireless too? Basically what I want is wireless system, 4 Door connectors, outside box, GSM to alert of event.

when setting the alarm i get the following error message + Line Failcom 1 what does this mean how do i get around this error message i am not connecting it to any phone line Also why does the Diagnostic LED flash- does this mean anything

So I am sorry in advance for the many questions, but I would rather ask that mess something up. I have decided to install my own wired alarm at home which is working out cheaper than the wireless options in the shops, I have opted for a Texecom Veritas Excel with LCD keypad, Texecom PIR's, Contacts, ext bell and also a Pyronix twin speaker/internal siren. First question - Should my brand new alarm panel smell (like electrical burny smell) ? Are they tested before being sent out. NO evidence of ever being fitted and no signs of board damage or heat exchange to components. It is brand new .... not refurbed or used. Secondly, I am putting the main control panel …

We are looking at buying the domonial system, the house is simple enough, requiring a Honeywell domonial wireless 2 PIR kit, an additional PIR, 3 more tags & a wireless siren. We also have two outbuildings that require protecting, the first is approximately 7m from the house (12m from the panel) it will need an internal alarm and 2 PIRs - one at 12m the other at 19m from the main panel, the signal would also have to travel through at least two solid walls, will it do this? There is also a barn some 45m from the panel, this is a bit more complex it will require 1 PIR and a door contact, we need to access it without always turning off the rest of the system and visa ve…

Risco Wireless Wisdom Kit 6 Wireless Devices could please send more details for the bell box is it totaly wire free

I am looking to purchase an alarm system and the Castle care has been recommended. On you site i can see the euro mini panel which comes with keypad but as i require a second keypad the only thing i can find is a unit with built in reader. Is there a basic keypad available?

I purchased an ade Optima Compact alarm system which I have fitted all seemed fine until I tried to alter the customer code from **** it would not accept the change but stopped the system from working. I have tried resetting the system back to factory settings as outlined in the manual but it does not work when the alarm is powered up it goes right into alarm but no LED lights show (not even the battery power)and the code **** does not rest/stop the alarm.

We're looking at a comms installation at an isolated site, which will also require an intruder alarm. There will be no landline phone but we anticipate installaing a 4G router which will provide both an Internet connection (WiFi and hardwired) and a phone line. The phone line will be derived from the cellular connection and we envisage using a UPS to keep the equipment going in the event of a power outage. The preference is for something that can alert the owner to an intrusion by dialling a series of phone numbers or by using SMS rather than by using a conventional. communcator and monitoring service. Remote Web maintenance is a requirement. Preference is for a system th…

We are Electrical Contractors (had products from SW in the past) normally install bells only systems but we have been asked us to replace an old system. (monitoring not required)customer ideally want a hard wired system planning to use Pyronix KX15DT`s and Pyronix Databell Plus My question is what would be a suitable control panel 8 zone minimum with 2 RKP`s which will allow programming etc with a Smart or Android phone ? Thanks Richard

Hello, My question to you is, do you sell 868 or 433 Mhz. recevers and transmitters (detectors) of the risco gardtec eurosec CPX range. best regards, C.Boogaard

Hi ! I want a good and simple home alarm for my little house and I think the Galaxy is well suited but there seems not no be any kits so I put down this list: 1 Honeywell Galaxy Dimension 48 LCD Kit (includes Keyprox & 4 Fob) 1 Honeywell Activ8 PIR - Single Channel 18m Quad Element Pet PIR 1 Honeywell Domonial Radio Door Contact 2 Honeywell Domonial Wireless PIR 1 Pyronix Twin Alert Internal Sounder Question 1: do I need external power /battery backup et.c or is it included or just optional? Question 2: What frequency is used for the wireless stuff? Question 3 Is there any other "cheap" wireless PIRs compatible available? Question 4: Do you have a…

Hi, I am going to replace my 23 year old system, and wnat to know if you sella kit, with : a control pane and key pad, and internal siren, an external siren, 3 pir sensors, wired, 5 wireless door sensors please ? How much, if you do, and do you have brown door sensors ? Then, how difficult is it to set the wireless sensors up please ? Cheers. Alan.

Please advise which is the best alarm system suitable for diy for under

Can you suggest a package to provide 3 x independently switchable on/off beams of 12m, 9m, 6m span with a control panel and sounder. The sounder to mute after a preset time. the system to be mains/ 12v powered. The detectors to be preferably powered from one end only of each beam. As cheap as possible, p.s. external use near the ocean.

i may need to put in a dialler later if the customer wants it. Which version will accept an internal card? The spec sheet implies that the compact will not but the other two versions will?

I need 2no wired zones aswell as the wireless ones. will the expander for the Powermaster 30 work or do i need the 8 zone expander?

Hi, I want to make a quick enquiry with wifi jamming becoming more common would this affect visionic powermax pro kit

hi, I am interested in purchasing a number of wireless intruder alarms. i was looking at some systems on your web page but i am unsure as to which best suits my needs. i wish to install wireless intruder alarms in 6 domestic houses. these systems do not need to be monitored by telephone line. i am looken for: 6 wirefree security alarm panels (no less than 30 zone) 6 wirefree external sounders 5 wirefree remote keypads 107 wirefree magnetic contacts can you let me know what kind of system would best suit my needs and a quotation for the overall cost. i am living in the west of ireland. will this effect delivery costs? if so can you include this in the q…

Hi, I received delivery of the MCS-710 a week ago. Upon installation the test button sounds the siren after 5 seconds, but it will not enrol with the Visonic Powermax base. There does not appear to be any wireless transmission. Regards

I ALREADY HAVE A VERITAS 8C SECURITY PANEL FITTED AND EVERYTHING WORKS FINE APART FROM THE BUTTONS. THE NUMBERS HAVE ALMOST RUBBED OFF AND SOME BUTTONS ARE NOT FUNCTIONING PROPERLY WHEN BEING PRESSED. MY QUESTION IS ...IF I PURCHASE A NEW VERITAS 8C PANEL FROM YOU CAN I USE THE FRONT PART OF THE NEW PANEL TOGETHER WITH THE BUTTONS TO REPLACE THE OLD FRONT.

I have a Visonic PowerMaxComplete system at home that I would like to connect to my PC to. Which of the following items do I require in order to do that, or do I need both?