Secware

I accessed your ecommerce from the zoneminder website, I would like to ask if it is possible integrate this sensor Model: SECWARE D20B to ZoneMinder and how.

The reson 8 bell has two tampers back and front please check both the tampers , the green LED indicates healthy tamper if it's not on that means there is an open tamper /tamper issue with Reson 8.

I had some difficulty with the, Honeywell Reson8 Bell Box during install at the weekend, i could not get SCB functionality to work, i initially thought the wiring may be damaged so i took the box to the control panel with a short cable and tried again, to no avail, the circuit on the sounder does not seem to react when the spring is depressed, and the case is shut. and the Green Indicator does not come on at any point. I have managed to use the sounder as sounder and strobe only, but wondering if there is anything else i can do to resolve, as the customer would like the lights on the sounder to flash and show the box is live.

Logic 6 alarm system as ordered, however it appears to be faulty. I was replacing an existing unit and wired the PIR’s, door switches and Exterior bell box and strobe. The system immediately showed a fault on the anti-tamper side. I removed the PIRs and tested the system with door contacts and it worked fine. On testing the 13v power contacts they are not showing any power reading although the batter is running the rest of the system. It would appear that the circuit board is wired incorrectly. I can confirm that the fuses are intact but no power is being shown at the output side

we have a question about the leds should they be left on after initial walk round test on the alarm? this is referred to on the installation manual to turn them off? or can they be left on?

Honeywell Activ8 PIR with Break Glass Sensor but can't find what i'm looking for. Firstly i think this PIR is per tolerant, can you confirm if it is? Also does it have seperate n/c loops for movement, glass break & shock or is it just one for all of them

No the Com300 will only work on the Elite or Premier control panel range

can the texecom com 300 model cea-0001 fit into a tex-dcb-0001 panel please advise

Visonic panels are not compatible with I.P lines (digital lines) It can work, but cannot guarantee reliability. The analogue to digital conversion is not always successful, therefore cannot guarantee any success when using digital lines.

I was just wondering if I can use IP telephony to connect to the alarm system. I know that it works with PSTN but I have my telephone via broadband modem(however I use a traditional telephone set connected to the modem

Now, for what you are describing, seems like you are using a PowerMax + panel. This panel has built-in all the terminals and connections to hard-wire a siren into it. If you were using a PowerMax Complete or a PowerMaster 30 panel, then you will to purchase an expander module separately.

I want a texecom control panel that can report zones triggered(names&location), o The zone text is a programmable feature in zone set up. users(name&number-if possible) who armed and/or disarmed the system, o The user name text is a programmable feature in set up users. power failure, battery fault and siren fault. o The Elite panel range have a time and date stamp event log from 250-5000 events dependant upon control panel.

I want a texecom control panel that can report zones triggered(names&location), users(name&number-if possible) who armed and/or disarmed the system, power failure, battery fault and siren fault. I'll be very grateful if you have or can have such a system. My clients want to get such informations(esp. Users& zones) specifically.

Option 33 on control Panel. "Inactivity Alert" Amend to appropriate setting An alert will be sent

I have a powermaster30 and would like to use the special features ,"Look after People at home" as described in the manual. in Devices configuraion of my PIR i have set the "DISARM ACTIVITY - YES, No delay" but does not receive any information if i stop moving. Is there anything else i have to configure in the CP to use this feature?

Hi , I'm after a bit of help , I'm looking at installing an external sounder to a powermax complete panel in out house , the eves at the top of the house so don't want to be going up ladder to often to change batteries etc . I've looked on your web page and it directs me to an expander module to allow the connection up to the siren, however looking in the panel I can see some connection for 12v , internal and external sounder already on the main panel next to the connection for the telephone line , therefore can I just use those to feed the external siren, thanks for your help with this .

Hi Ulf, Sadly the UK and EU work on a different bandwidth, and the UK version has not yet been released. We currently stock the KP-160 with symbols only, for arm/disarm by prox.

Hi Ulf, Visonic do have plans to release a new version of the KP-160 which will indeed have numbers to be able to arm/disarm. However this has not yet been launched. Having chased a launch date have been advised 2nd Quarter of 2014.

The sounder requires a negative trigger to operate. Is the panel giving out a negative trigger? Is the control panel programmed as scb?

texecom odyssey bell box appears to be faulty, I have checked the voltages and the tamper circuit but the bell is active constantly. Is there anything that can be done about this?

The informa speech dialer is compatible with 8EP396A panel on the bell -ve trigger terminal.

HI Ulf, The KP-160 is a proximity unit only for arm/disarm. The current Powermaster 10 SW is Version 17.

Can I connect a telephone dialler to the Optima 8EP396A . The instruction manual says the communicator is not fitted to the Optima Compact.

The CGC-0001 is the UK version, the CGC-0002 is the international version which has the below available languages: ENGLISH SPANISH Belgium FRENCH Belgium DUTCH DUTCH DANISH