Secware_Tech6
-
Posts
258 -
Joined
-
Last visited
-
Days Won
14
Content Type
Profiles
Forums
Events
Posts posted by Secware_Tech6
-
-
What wireless rx are you using. I assume this is then connected to the panel hard wired?
-
Hi
Solar powered cameras are usually diy type products and not professional grade. There are solar options but due to the size and cost and usually specialised. Plus you will need to run some sort of wifi transmitter as well as the camera. You will also need to consider the time the camera and any ir emitter will have to function during hours of darkeness and low recharge output in the winter,
-
Alarm battery calculator tool
-
The aritech se sirs require either a compatible panel or an analyser.
You may be better off with a knight combined unit
-
As above converters are not designed or tested for this purpose. It may work 80% of the time but may not when actually needed. You need a communicator designed for ip or gsm
-
Yes you will need a compatible lock case to suit the door type
-
You can use either the HKC with standalone contacts in enclosures eith HD external contacts
or the pyronix enforcer.
Both will function without internet but notifications wont be possible,
Note our products are designed for professional installer use
-
Unfortunatly not
-
what you need is a shunt lock. Different lock types are available for different doors, backsets etc
-
Any hard wired bell would be suitable.
We do offer SW bell stickers to add to the unit
-
It sounds like you have either a failed controller or pir.
DIsconnect all pirs andding one of them (test each one) and see if the fault disappears. If so start adding pirs back into the system until the fault reappears
-
The panel will require an ethernet module and then the ethernet cable can be plugged in
-
honeywell fob. there are also honeywell compatible available
-
Id look at the fike twinflex or better the addressable fike as this provides automatic hush in a HMO type environment
-
I dont know of a manufacturer that supplies boards only. But may be available as a special order. Usually one would replace the whole sounder to keep it looking as new as spossible as this is the detterent
-
Yes you will need a usb to serial converter. Or a PCI card supporting 232 serial
-
You do enable / disable the circuits you want in each part set.
-
the newer hkc micro rf sensors can be hidden if there is sufficient space. But will require a hkc panel
-
Bosch or Honeywell are popular pro models
-
Its should be 12v DC
-
Any non addressable sab will be compatible. ie CQR
-
Have you confirmed all the wiring is OK?
-
Its a detector, would need to be part of a solution.
-
Re the cctv do you have a preffered brand? Agree on the toy town stuff most budget equipment is exactly that.
Alarm system wise again i dont know your expereience or preffered equipment?
How do I omit a zone on a Scantronic 9651 with 9941 keypad?
in Intruder Alarms
Posted
Omitting Zones Your system may be programmed so that you can omit individual detectors.
Ask your Installer which zones can be omitted.
To omit a zone:
1. Key in your access code or present a tag and press X. The display shows: Omit Zone?
2. Press the number of the zone you want to omit (for example, key in 07 to omit zone 7).
3. Press Y. The sounder gives a double beep and the display shows the zone number followed by an "o": Note: Omit Zone? Omit Zone 07o If the display shows a “x” after the zone number then you cannot omit that zone. To omit further zones repeat steps 2 and 3.
4. Press X to finish.
To set the system with an omitted zone:
5. Key in your access code (or present a tag) and press a Level key..
6. The control unit gives an error tone and the display shows (for example): A:Omit Zone 07?
7. Press Y. If necessary, press Y again for each omitted zone shown on the display. (If you wish to escape press X.) After you press Y for the final omitted zone the control unit starts to set.