Intruder Alarms

On the keyboard of the alarm Veritas excel is there a menu or a program in French?

I have installed veritas r8 panel last year , I was wondering if it is possible to somehow have it so it contacts my mobile phone through my internet router when going into alarm mode, I know you can get a communicator , I have used these in the pass, but I do not have a land line anymore, like many people I use mobile phones, hard wired to my router would not be a problem , your help / advice would be appreciated ,

Logic 6 alarm system as ordered, however it appears to be faulty. I was replacing an existing unit and wired the PIR’s, door switches and Exterior bell box and strobe. The system immediately showed a fault on the anti-tamper side. I removed the PIRs and tested the system with door contacts and it worked fine. On testing the 13v power contacts they are not showing any power reading although the batter is running the rest of the system. It would appear that the circuit board is wired incorrectly. I can confirm that the fuses are intact but no power is being shown at the output side

Hi I have a 3-5 year old (can't specifically remember the age) HoneywellTotal Connect 2.0 E system in place with multiple motion sensors, fobs, tags ect....and the control panel seems to have failed - it's not transmitting anymore. So we can't secure our home manually or even using the App. Am I right to assume by purchasing the following new control panel (https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/kits-c-36_62/honeywell-suepacke-panel-with-gkps8m-keypad-and-four-tags-p-4880.html) it will effectively plug and play with all the existing peripharels (obviously after having to reset the system and reconfigure/link it all back together)? Will the new con…

check outputs? can anyone help me make sure i set it up right and what to check/fix i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the extern…

I keep getting a tamper alarm, what are the common reasons for this happening? Risco Gardtec G-Tag Contour Keypad & PA(595 & 800 Series)4 Wire Thank you

Hi, Just wondered if you could tell me please how to change the volume on the 16 ohm speaker? I have one but can’t figure it out. Are they just one volume or is it changed at the panel? There is no adjustment at the keypad. https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/sounders-c-36_45/internal-sounders-c-36_45_139/secware-16-ohm-internal-speaker-tampered-grade-3-p-5040.html

I am interested kit solution with GSM capability. I would like the alarm when triggered to be sent as SMS to predefined mobile phone numbers and possibly even place calls to predefined numbers. Also I would like to be able to configure and receive status by sending SMS command. I would like to have two identical kits: Each kit has 2PIR, 2 door contacts, 1 control panel with GSM, 2 Keyfobs. The control panel can be either Plus version of Pro version, would like to know the difference on pricing. And if I have the flood and smoke detector connected, can I configure the control unit to send out different SMS to different number based on different types of…

we have a question about the leds should they be left on after initial walk round test on the alarm? this is referred to on the installation manual to turn them off? or can they be left on?

You sold the above to my installer when I renovated my property in 2012. I have never actually used it but now looking to start using it. The engineer at the time left me an engineers code which i cannot find nor can I remember the code I used. Is there anyway I can now get the alarm working? Your advice would be greatly appreciated or any contact at Scantronic. Many thanks ps a contacted another firm told me I would have to buy a new panel through him which I find hard to believe.

Can you kindly advise ideal system for the following criteria; Looking for alarm with ID Plus for my PIR's due to wiring setup of them. 15 sensors in dwelling. Only need the control panel and keypad as all other hardware in situ. wishlist: if system has sms or dialler also remote arm and status. Price up to approx

MDT Avanti LC Steel Control Panel https://www.securitywarehouse.co.uk/catalog/intruder-alarm-equipment-c-36/security-control-panels-c-36_102/control-panels-all-c-36_102_41/mdt-avanti-lc-steel-control-panel-p-1000.html Hi, can this unit ( Avanti LC 9EP309 ) replace an old ( Avanti XP PLUS Steel Panel unit - Product Code - 9EP322).

I am looking to purchase some CQR FreeWave products and you have the 240v Interface and Keyfobs, but the 3 channel module. Is this something you can source and what is the price please?

Bought myself a Jablotron JA-83 panel. The manual advises to connect only 1 wired keypad (JA-81E). Additinional keypads should be connected wireless. Does anyone have an idea why ? Is this panel not able to work with 2 keypads on the same keypad connectors? Does the panel delivers not enough power to feed more than 1 keypad? Or does Jablotron likes to sell wireless keypads above wired ? I really would like to know why...

I need to buy a new inertia vibration sensor, as I have a voltage free alarm system, I have been looking on your website and not sure if I need the GS611 - W or the GS610. Please can you advise.

I'm trying to install the Ion-40 wired keypad with my existing i-on 40 main panel. At the first mains switch on (with back-up battery and wired keypad connected) the manual says you should get option A and B on the keypad display. I get this on my display but the entire left side of the keypad buttons -including the A, B, C & D buttons (but excluding the big square button) do not do anything - ie when I press them, nothing happens. Pressing the others makes a beep and the keypad back lighting comes on for a few seconds. The only other useful thing I can add is that the 'heart-beat' LED on the main panel is flashing and when I override the main alarm panel tamper swi…

Will the COM-ADPT-02 allow the i-on30R control unit to adapt, to allow a com-data-wifi module to be added

I have a Reson8 bell box with an intermittent fault that I wish to replace. As I understand this is now an obsolete item, could someone advise the most suitable compatible replacement for the Optima Compact 8EP396 A panel. Thanks

I have recently purchased 2 x Honeywell Combination Optical / Thermal Smoke Detector (58

I think I need 11 zones: Kitchen door (E/E) Front Door (E/E) Workshop PIR Garage PIR Lounge (Pet Friendly PIR) Hallway 1 (Inhibited Pet Friendly PIR for E/E) Hallway 2 (Pet Friendly PIR) Bedroom 1 (Pet Friendly PIR) Bedroom 2 (Pet Friendly PIR) Dining room (Pet Friendly PIR) Kitchen (Inhibited Pet Friendly PIR for E/E) 1 x RKP External Sounder Is there a system/ kit that will do this (Honeywell Galant? - is this panel obsolete?) or can I link multiple PIR's to use the 8 zone kit as advertised Honeywell ADE LCD Accenta 4 x Pet PIR Starter Kit

Hi, we are looking for a ?security chain? to attach to an out-board boat engine. Should the chain be tampered with we would like an alarm to sound in the house, not at the boat, maybe 30 metres away. Do you have anything suitable? Thanks

Hi, we have constructer a community hall with aluminium windows and doors. Do you have a door and window sensor which can be wired into the building security alarm or wireless which can be concealed in the frame? The Client does not like surface mounted door alarm sensors.

can the master blaster siren be connected straight to230v supply via key switch without 12v relay supply,just need siren with 230v connection.

I have your verutas 8 and i have just added another remote key pad, all works fine but i cant seem to get out of engineers mode, i go to program and put my new code in but when it comes to full alarm it will only respond to 4 3 2 1 any surgestions?

I'm installing a Texecom Premier Elite system in my house. Looking at the Odyssey X sounders they all have the window for an alarm installer to put their logo. Would this look odd without one? After a some searching I found the Odyssey 5E. This looks better (no insert window!) but perhaps an older model? Are there other boxes that might be better for my DIY use case?