Intruder Alarms

Hi, I am about to purchase the items in my Checkout Basket and would like confirmation that the chosen items are all compatable with each other. Also I require a dummy LED to go with the dummy backplate and cover, can you advice if you have this item for the Texecom ODYSSEY 3. I also require info on which backup battery is required and fits in the control panel I have chosen. The following items are in my Checkout Basket: 1off- Scantronic 9651EN-43 (9651 c/w 9943rkp) 6off- Bosch Blueline ISM-BLP1 PIR Detectors 1off- CQR SOINT1 internal sounder 1off- Texecom ODYSSEY 3E Live Backplate 1off- Texecom ODYSSEY 3 Dummy Backplate 2off- Texecom ODYSSEY 3 covers 1off- S…

I am having difficulty in setting up this unit. My main exit entry is via zone 5 full set A. At night the main exit rout is via zone 2 and set with B. The problem is that if you enter through zone 5 when part set in B the system does not recognise zone 5 is open. Can anyone help?

Now that I've replaced the old Optima with the new Optima 2 lanel, I'm now trying to swap the old sensors with the pet friendly Active8 PIR models. However, new sensors have: 1: EDL (single connection) 2&3: Tamper (double connection) 4&5: Relay (double connection) 6: EOL (single coneection) 7: 12v + 8: 12v - Two of my old sensors have: N/C Lt Blue then Yellow Propose: Relay 4&5 + Red Propose: 12v + 7 - Black Propose: 12v - 8 24hrs Lt green then white Propose: Tamper 2&3 My remaining sensor has: Alarm Lt Green then White Propose: Relay 4&5 + Red Propose: 12v + 7 - Black Propose: 12v - 8 Tamper Empty and Empty Please…

I need a new alarm panel with voice gsm support for at least 16 hard wired + wireless. I did not know if I should get a gsm voice dialer or a new panel.

I bought a Texecom IMPAQPlus from you back last year and you gave me help with the wiring for double EOL, unfortunately my builders have pulled the wires out and I can't remember how to wire it, I know I had to put a wired link in, please can you remind me on how it should be wired. Thanks

Hi, just been delivered secware optima2 pet kit to replace old optima system. Wired unit fine, now trying to wire siren. Old siren has connections, linked to wire colours in () Strobe + (White (strobe)) Strobe - (lt Green (strobe)) T (Blue (scb)) E (Yellow (scb)) A is linked back to E via metal loop D (Red (bell)) R (blk (bell)) New siren has: ST- R- SW- V+ V- The given instructions are for the Optima XL4 and don't seem to make any sense. I seem to have 6 wires, and only 5 terminals. Can you help?? Looking again and researching on the net forums, I'm now thinking: AG6 Optima ST- to Strobe- (Lt Green) R- to T SCB (Blue) SW- to …

Maybe unwisely, I have bought a used SD1+ Speech Dialler to replace a twelve year old model that failed to respond to all the helpful advice you gave me back in February. I have carried out a factory restart, as described in the manual, and have created a 'NEWCODE'. However, when I try to program telephone numbers from 'READY' and press'ENT', the LCD still shows 'READY'! Again from 'READY', if I press 'O' 'CLEARBY' is indicated. But pressing 'B', 'CLEARBY' still remains on the LCD! Please can you help me!

Subject says it all really: I've installed a Scantronic 9651EN-43 into an existing "wired" house and extended the system using the Visonic MCT-302/MCR-308R wireless system. I've linked the Visonic zone output into the 9651 zones and also linked the anti-tamper into the main loop as well. The Visonic can send a low battery warning and I need some suggestions as to how the 9651 can handle this? Obviously, it needs to bring the warning to the home owner's attention, but it can't prevent setting the system or set off a full-blown alarm if it occurs whilst the system is set. Many thanks for your assistance!

Having received my domonial kit it had no instructions with the panel. I've spoken to Honeywell and they have emailed a copy but it seems to suggest that I need some programming software to program this panel... There isn't any with my pack. Can someone please tell me what's going on?

i am looking to buy control panel witch can accommodate 8 pir and auto dialer and i would also like to buy autodialer (speech dialer with at lease 5 numbers ) and if possible fob entry system with 4 key fob's

hi there i have an old karizma plus id system that i would like to replace with out replacing the original detectors and id biscuits i have been told that the texecom premier systems will work with the old id biscuits. Please can you tell me if that is correct and what i would need to purchase for it to work?

Is the MCS730 compatiable with the powermax + panel?

Hi Have installed this Powermax plus quick fit , all is working but it comes up with a trouble fault of Tamper open on Zone 30. This Zone is not used and the resistors are crossing the Z29 GND and Z30GND , could you advise how to resolve this? The panel is arming

Do you do the optex detectors with optional heaters?

Hi, i'm looking to buy a wireless digital alarm system with at least 16 zones. i'll also need the contacts and pirs etc to go with it. Can you help?

I am trying to buy 25 pieces of the Yuasa NP7-12 buy your system restricts to only 5. Can you help?

I have problem where the dialer will dial out when made to do so through test setup/Engineer mode no problem but doesn't dial when the alarm is activated. Is this Informa faulty?

Does anyone know how many PIR's can be connected in series together in one zone of Scantronic 9448EUR-90?

Can you give me a price for the Powermax Pro please? Your web site says 'call for price'.

what all does the ethernet adapter let you do with the galaxy unit. I was wondering does it allow u to arm/disarm the unit with the honeywell iPhone app.

Hi, I had some problem getting the SMS work with the service provider here in sweden and therefore I'am thinking about using the internet and try to avoid using an ordinary alarm central. 1 Do you have any equipment I can use to send alarms via internet from my alarm panel? 2 Is there any crude variant where I can let the alarm call my mobile and I can get some status and maybe even control the panel with my mobile phone? Best reg.

My internal sounder registered fine with the domonial control panel, and on viewing through engineering mode always registers a high signal (7/10) However, whenever I set (full or part) the alarm, typically every other time I get the 'INT SOUNDER RADIO LINK' error. I've configured the system to ignore these errors and set regardless without requiring confirmation - but my worry is there is a fault which might mean the sounder does not go off in case of intrusion. Last week I tried changing the batteries (on the off-chance the batteries supplied were low given the packaging was open), but this did not solve the problem. The positioning of the sounder is very cl…

Could you please advise as to whether the Scantronic 723 Keyfob Set/Unset Transmitter works with the ION16 and ION40 Scantronics alarm panels. I need to be able to use for both Set/Unset and PA functions VERY IMPORTANT that both can be done.

Hi I have seen your Veritas R8 alarm range I think the items below are right, please can you confirm they are all correct prior to me placing my order. 1ea.- CQR 6 Core Intruder Alarm Cable 1ea.- Texecom VERITAS REMOTE KEYPAD 1ea.- Texecom VERITAS R8 4ea.- Texecom REFLEX 1ea.- Texecom ODYSSEY 3 LIVE BACK PLATE 1ea.- Texecom ODYSSEY 3 COVER WHITE I have ordered an extra remote, I also need batteries but it says sold out so please can you tell me the batteries I need and cost,order number etc. Please can you also confirm that I am buying this the cheapest way and not missing any offers and that I have not missed anything obvious ?? I dont need an internal s…

I am trying to install Scantronic 9448EUR-90 board with two Takex MS100E multi pattern sensors connected in series on Zone 2 (all other zones are disabled) and Elmdene Quartz 1000live sounder. My problem is that control panel shows temper fault - all boxes are closed, all cable connections verified. If I reset the panel by disconnecting battery and main supply the temper light will go off Zone 2 light will go on and when you try to set the alarm with users code the temper lights come up on again. Could somebody recommend how I can solved the problem?