Intruder Alarms

is it true that Visonic plans to stop production of the tower 20am?

Hi, I want to purchase 1x heat sensor and 2 x smoke sensor to add to my current BT VP1000 alarm system. Can you advise me on what is compatible with it.

Hi, I am told with this system, powermax plus, I can get Pir's to hard wire. I want to hard wire 3 Pir's, but see only 2 hard wire zones. What pir's can I use for hard wire please, and are there pet friendly ones ? Which hard wired external alarm can I buy with this ? Are all batteries included with the system please ? Wanting to buy the visonic plus control panel, 5 wireless door contacts, brown colour, 2 wireless pet tolerant pir's, 1 hard wired pir, 1 wired external alarm, 1 dummy alarm box, and 2 key fobs / Can you give me the best options kit wise, and cheapest way of buying these, and total costs please ? Thanks, Alan. alanbl@sky.com

Is it possible to change the mk7 panel to a mk8 in this kit? What option do i have if i want alrms tomy gsmphone? http://www.securitywarehouse.co.uk/catalog/honeywell-galaxy-220-wireless-starter-kit-p-1632.html

Hi Have installed this Powermax plus quick fit , all is working but it comes up with a trouble fault of Tamper open on Zone 30. This Zone is not used and the resistors are crossing the Z29 GND and Z30GND , could you advise how to resolve this? The panel is arming

I have a Menvier TS690id system and am after another keypad and ID chips. The panel will accept the ID plus chips. Do you stock a keypad that will work with this panel and do you still have id biscuits in stock. Also will your proximity tag readers be compatible with the netled/netlcd keypads already fitted as an upgrade and any new keypad you can supply for the system, if not fitted into the keypad.

we are looking to fit a wireless alram to a five bed house where we will have 10+ zones, would like a keypad by the main door, so need one where the main control panel can be more like an end station. would also like to be able to control via mobile phone when away. which good quality system would you recomend

texecom odyssey bell box appears to be faulty, I have checked the voltages and the tamper circuit but the bell is active constantly. Is there anything that can be done about this?

PowerMaster 30 0r 33 + 2-way communication I have a phone line and modem next to box House and garage 1 PM 30 or 33 (IP) 3 PIR (Camera) 1 Dummy + Flash 5 x PIR (2 x Garage, Kitchen, Dining room, Landing) 1 X Key pad 1 x Siren with flash unit (main building)

I just bought an AMDT and I'd like to understand the purpose of the SET wire. What is the Alert/Set mode ? Should it be left unconnected (and be in the standby mode) ? BTW, what is its current drain ? Thanks.

is there anyway of turning down the volume of the ADE Honeywell MSN Multi Siren MS-N on the entry & exit of alarm?

Hello all, I fitted an alarm system a few years ago and put contact breakers on my windows. To save on wiring I "shared" the different wires within the 6 core cable I used between 2 zones, with a common tamper circuit, on the rear of my property. I have now had sliding sash windows fitted which have made the contacts unsuitable. I was thinking of replacing them with vibration detectors but noticed that some have LED's. I assume this means that they need a power source to operate - the same as the wiring for a PIR detector. Are non-powered vibration detectors available or will I have to rewire with 8 core in order to maintain my zone separation? Thanks for any help…

i am looking to buy control panel witch can accommodate 8 pir and auto dialer and i would also like to buy autodialer (speech dialer with at lease 5 numbers ) and if possible fob entry system with 4 key fob's

Installed an enforcer panel roughly 3 months ago and it has been working fine, setting and unsetting no false alarms etc, a few weeks ago it started flagging Mains failure, a code was entered to silence it and mains was restored. the following day it started flagging up LOW voltage on the screen, a code was entered to silence it but the orange triangle remained, the panel then died. I opened the panel and checked voltage going in and it was 240v, the battery must have ran the panel for about 14 hours but i dont see why it didnt recharge the battery because the mains was and still is entering the panel. Any suggestions or repairs i could make as its now providing no securi…

You sell them @

I have a GC Simon wireless alarm system (model: 60-911-010-4-IE) and one of my door sensors has developed a problem and needs to be replaced. However I am having great difficulty in sourcing a suitable replacement. I did by a recommended replacement from the USA but this did not work. I think because the system I have is 433Mhz and the new sensor was 319Mhz. Can you recommend a replacement sensor and where I may purchase same. Thanks in advance and regards

What is the differences between the CQR FW/GD04 Communicator (GSM) and the visonic GSM-100? Are there any other gsm-modules that are compatible with the pm+? My pm+ controlpanel is bought in sweden, will I have any problems if I buy any of the gsm-modules you have from UK? Will the sms-messages still be in swedish?

Hello! I have bought a nice second hand DSC wired panel (PC1864) and is looking for some detectors. I am among other things considering the https://www.securitywarehouse.co.uk/catalog/rokonet-shocktec-with-magnet-white-p-620.html As I understand it this unit does not require any external analyzer card or anything and should work as any stand alone wired detector with my DSC right? I am thinking on using it for the doors on my house - do the main part of the detector in this case need to be mounted on the door itself or will it detect vibrations from break ins even if mounted on the frame? Do this unit have space internally to mount resistor? Do you have some install…

Hi, I'm interested in purchasing your product 166/173 (Visonic MCM-140). Before I do can you tell me if this is the 868mhz version?

I’m after 2 No. keypads compatible with the 4 wire Gardtec 600 or can you recommend a compatible alternative.

Hi Does the Texecom Premier 24 include a remote keypad or is that an extra bit I need to buy?

I would like a wireless single PIR, single door, telephone dialing warning unit with small key pad for a 2rd floor two bed flat. Ideally I'd like an internal and external audible siren but would settle for either. Scantronic have been recommended. Any ideas on what to buy rom you please?

Can you tellme what battery will fit the honeywell large plastic cased accent gen4 with key pad and also can the honeywell compact per with pet immunity be used as a normal pic or will i have to order a honeywell IS3016 so it matches. Thanks.

You have 2 items listed on your web site from Texecom. TEX-CGC-0001 which is listed as a Speech and Text Dialler at

Have bought Gen4 RKP to replace old Gen3. No engineer programming info was supplied. Can you help please