Intruder Alarms

Also I have a question about the Genesis 7ah 12v battery http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&products_id=1340 Will this battery fit inside the Scantronic 9751 control panel? http://www.securitywarehouse.co.uk/catalog/index.php?main_page=product_info&cPath=36_102_41&products_id=549 Your reply will be appreciated, as I wsh to order items as soon as possible. Thanks

I'm fairly sure I can interface the Reson8 bell box to an old RS alarm Panel I installed many years ago. The panel has (in order) + Hold off, - Hold off, -SW, +SW, -ExB, -ST-, + IntBell, - IntBell, +Buzz, -Buzz, -Tamp(Zone1),+Tamp(Zone1) Basically I cannot see how to connect the Tamper supply- and Tamper return- in the Wiring diagram. I am sticking with the wiring colours. I know it's quite serviceable.

Hi, My G2-20 is set to EOL and all the other sensors I have purchased from you have had EOL built-in. I guess the Activ8 BG I purchased does not. Can you confirm how I should wire this to my Honeywell Galaxy G2 panel. I have two zones spare that I'd like to use for the motion and the break glass feature of the Activ8. I guess I need to wire a 1k resistor between two of the terminals but not sure which ones. Terminal 1 & 2 - Tamper T 3 & 4 - R-PIR (normally closed) T 5 - EOL T 6 & 7 - R-MIC (normally closed) T 8 - +12v T 9 - GND Many thanks.

I would like a wireless single PIR, single door, telephone dialing warning unit with small key pad for a 2rd floor two bed flat. Ideally I'd like an internal and external audible siren but would settle for either. Scantronic have been recommended. Any ideas on what to buy rom you please?

Hi, I am told with this system, powermax plus, I can get Pir's to hard wire. I want to hard wire 3 Pir's, but see only 2 hard wire zones. What pir's can I use for hard wire please, and are there pet friendly ones ? Which hard wired external alarm can I buy with this ? Are all batteries included with the system please ? Wanting to buy the visonic plus control panel, 5 wireless door contacts, brown colour, 2 wireless pet tolerant pir's, 1 hard wired pir, 1 wired external alarm, 1 dummy alarm box, and 2 key fobs / Can you give me the best options kit wise, and cheapest way of buying these, and total costs please ? Thanks, Alan. alanbl@sky.com

I think I have damaged the PCB. It shorted as I was removing a connection when still live. I've replaced the blown fuse but, on rewiring, it alarms as soon as the system is set. I'm confident the wiring is correct & unit programming OK (I did a factory reset). There is no fault with the PIRs. Any suggestions on how to remedy?

Good afternoon, I purchased a Veritas system with lcd keypad. The issue I have is that the keypad is showing a tamper fault and the tamper switch does not seem to be working. I have check all of the system and everything else seems in order. Is there an reason this would be a fault ? Kindest regards

Hi I have a 3-5 year old (can't specifically remember the age) HoneywellTotal Connect 2.0 E system in place with multiple motion sensors, fobs, tags ect....and the control panel seems to have failed - it's not transmitting anymore. So we can't secure our home manually or even using the App. Am I right to assume by purchasing the following new control panel (https://www.securitywarehouse.co.uk/catalog/intruder-alarm-c-36/kits-c-36_62/honeywell-suepacke-panel-with-gkps8m-keypad-and-four-tags-p-4880.html) it will effectively plug and play with all the existing peripharels (obviously after having to reset the system and reconfigure/link it all back together)? Will the new con…

Hi there Is it possible for you to give me a price for a replacement control board for a texecom Veritas R8+ end station? I have the transformer. Can you also price up an ADE reson8 bellbox please?

Hi I have a Guardtech D500 system installed in my home an it incorporates shockguard sensors etc. I have just had new double glazing fitted and some of the sensors have been damaged, I would therefore like to upgrade my system with a new one as the wiring is already in place for the sensors I would like a wired and wireless system to increase security, I have been looking at the 595 or 816 and have spected out as system below can anyone tell me if this would work and if i have missed anything out? Guredtec 595 or (816 which has 16 zones, can I use each zone for each shockguard window sensor is this correct) 2 x wired surface mount magnetic door s…

i have respond/eclipse wireless system fitted in the house occasionally i have my van in the driveway would this "Risco Wisdom Wireless Shock Detector" be suitable to fit in the van? or can you recomend one that woud work with my alarm

Proposed Gargage Alarm System Before placing a package order I just need to confirm that the Scantronic 9651EN-43 Panel will support 2 x remote extension speakers. I note it has 3 fully programmable outputs, I need a volt free relay / contact output (N/C healthy) Open Circuit on alarm condition for remote signalling to an existing Scantronic 9752 panel located in the house (this will then represent a seperate zone alarm, just like say a PIR in alarm condition going from N/C to open circuit) - please could you advise, order ready to go.

Hi I would be interested in buying Visonic alarm system. However I am not clear on the PowerLink functionality. Do I have to have Visonic IPMP server installed separately to support PowerLink for exactly this: sending emails/MMS messages with pictures from connected cameras UPON alarm trigger.

Hi, my Siren for the pyronix enforcer MK2 is low battery. Is it simply swapping the old batteries out and no programming needed Thanks

Hello can anybody give me some advice on adjusting the volume on the above alarm system to low, altering the volume adjustment on the PCB has no effect the volume tone is quite loud, I had an accenta 8 system previously installed and had the same problem?. There is an intenal speaker fitted. Thanks

I HAVE A RISCO ALARM FITTED WHICH CAN BE ACTIVATED REMOTELY, I AM GOING TO BUY THE RISCO 4 BUTTON REMOTE FOBS, DOES ANYONE KNOW IF THEY COME WITH PROGRAMMING INSTRUCTIONS ? OR IF NOT DOES ANYONE KNOW HOW TO PROGRAMME THEM TO MY SYSTEM ? THANKS

Hi! I bought a Visonic Powermax Plus last week (Thanks SecurityWarehouse !) 1. Is it possible to change Visonic Powermax Plus language ? 2. I've got two balconies : o 2 m x 3 m o 2 m x 6 m What is the best wireless protection for this balconies ? New Optex FTN-R/FTN-RAM ? Do you have other solutions ? Thanks, Jose.

I just purchased from you the homelink 75 alarm system. I would like to purchased alarm box to put on the side of my house and operated the alarm system when we are upstairs at night. Please could you let me know which equipment I need to buy, thank you.

Hi, Need an alarm system asap as I've just had an attempted break in and it's given me the kick up the backside I needed. Complete novice at alarms but a competent diyer.Please recommend me an alarm system for a 3 bed semi, conservatory upvc patio doors to the rear, upvc side kitchen door and upvc front door plus 2 downstairs windows need protecting I think i will need 4 pirs for the down stairs rooms Kitchen, hallway,dinnig room and lounge and 3 surface mount door contacts. I would like to have a panel upstairs so the alarm can be armed at night. I think I will need an extra bell box for the rear of the property please advise. Please recommend wired or wireless whic…

I need to change the battery on my alarm will the Enersys 12v 2.3 A/h Battery be a suitable replacement?

Re: Pyronix Deltabell Plus External Sounder Module Grade 2 Hi I have a dummy rear box. Could I simply connect 12V to this and make it light up my box at night together with the 2 LED flashers?

We are looking for a fully wireless, self install inturder system for our Gardeners Yard, we would need a few internal motion detectors and door contacts and some external gate contacts, we also would want some external sirens. We do have some power in the building for the base, but no internet and very little 4G signal., Is this something you can advise on?

Is the 9448 manual the same or similar to the 9448+ manual as I need to gain access to the panel without it going into full alarm. Or can anyone tell me how this can be done. I have installed many Optimas over the years but never got involved with Scantronic.

Currently have A Veritas R8plus 10 years old that is now faulty. Would like to replace with a new one, is current model a direct replacement to old. Does new unit come with battery. Can it be replaced by DIY

Looking to buy a veritas excel and want advice about PIRs ie Mirage or Prestige range.