Intruder Alarms

enter engineer program mode scroll thru to P enter3 inhibit zones press x 3 times leave engineers mode system unset enter user code press p LCD still only offers set program 1 no other option offered

Sorry all you good people out there, to ask these questions , but I do not know whether it is I who is Dim or could the Electronics actually be at fault ?. When I try to register the keyfobs under other devices and I go to arming station I am asked to activate the tamper , A Is this the correct section to be in . B As there is no tamper do I just press any button or what. Also with regard to the Tag I am supposed to offer this up to the top left of the panel . I am in the arming station section but nothing is reacting. Again am I in the correct section and is there any way of verifying the Tag is working. I have proved that the Fobs are working by …

I purchased the above from you as a replacement for one in which some of the pressure pads are not working. When installed, will the new unit retain my original 4 digit code?

I purchased several items including a ADE Honeywell Accenta Mini Gen4 and a Honeywell ActiveGuard AG6 External Siren to update an old system in my house. I fitted the items and all seemed to work well. However I have just realised that when I remove the PCB cover, activating the tamper, the external bell and strobe do not operate. The sounders on both of the key pads are activated by the tamper. The external siren and strobe work as they should in all other situations (test, SOS, if the alarm is triggered etc.) I just cannot work out what is wrong, any help would be appreciated?

I am contacting you regarding this product because we have the same products in our house they work superb and I was hammering something in behing one of the sensors and it now just shows up on the alarm system as fault on landing so can you give us any suggestions as to what to do ? Thank you

Recently installation of a galaxy flex and looking to put Ethernet module A083-00-01 into it On looking at the other flex systems they are all in plastic boxes with the RF Portal as a seperate card inside this flex is in a metal box. Honeywell Flex 20 Small Metal Box- C005-S-E1 & as seperate RF Portal -C079-2 Does anyone know if the Ethernet module can be used within this flex? Thanks

Hello, I have purchased a CQR 3/8 Flush Contact 1 RD 4 Wire White, but it does not work on my door. Most probably, it's because the gap est too large and the metal door interfere with the contact detection. I am looking buying a new flush contact. Which one do you recommand? You have so many. The installation environnement is: metalic door, large gap (difficult to measure, probably at least 10mm), if possible a contact with direct wiring. Looking forward your answer

Hi All, I have a Galaxy Flex 20 panel installed with x10 PIR's, x2 door contacts, SMS & ethernet module. I need somebody with Galaxy Flex knowledge to commission all of the above (including GXRemote app). Please PM me if interested with anticipated costs. Cheers G

Hi. I am interested in a Powermax alarm system, but need some information and advice. First, I live in Sweden, shipping available? And if so, could you please state the total price delivered to me? Our needs are for a two-storage residential home at a total of 145 square meters There are two main entraces and two patio doors in glass. The two patio doors are in immediate proximity to large window portions with windows from one side of the room to the other at a total of two times 5 meters and reaching from floor to roof. There are also a bathroom window and two windows at the entrance from floor to roof. We want to have the possibility to arm the alarm for

I would like to exspand the system I have,which is PA 4 WIRED alarm (Friedland)to ad to the system with two OPTEX SAVER NEW QUAD PIR. Would this be suitable.The movement detectors I have,have got 6 connections in it.

Hi, how to wire the kx15dtam sensor to the Optima alarm panel.I simply want to replace the now obsolete Equinox E sensor. Thanks

Hi, Just bought from you a visonic powermaster 30 kit with some additional modules and sensores and have the following questions : 1) The Next PG2 K9 motion sensor come with 2 lens, what is the lens that is Pet tolerant? 2) I would like to buy a RS232 module to connect to the powermaster using the "Remote Programmer PC Software". Two questions : 2.a) What is the RS232 module that it's compatible with the powermaster 30? 2.Do you supply also the "Remote Programmer PC Software" ?

Hi, Having problems programming Honeywell Domonial wireless 2 PIR kit Thanks

Hi I have been roped in to help a friend that has an alarm panel that has died. I am looking for a panel that is 1. Easy to install 2. That can work with Biscuit ID wired sensors 3. Not expensive I think it is 6 Zone. Any ideas?

we would like to fit a wired Alarm system, we have made the following list of items We like the look of the scantronic 9941 box as we would like to put a TSD2 speech dialler on so that we can telephone and check the system remotely. > > We would then like to put a remote keypad in the porch area at the front of the house which we would like to have night set options. We would also like to have a personal attack button and maybe a keyfob to de activate the system. We would like an internal sounder but maybe this is built in to the system. > > We would like a siren and strobe sounder on the front of the building. > > Detection Points > > …

Hi, first post Can anybody tell me the recommended way of wiring a Texecom Premier48 and PSU200XP combination to the mains supply? Would each panel require its own fused spur? I will not be undertaking this work myself, but would like to have some knowledge of what is required before approaching an electrician. Thanks in advance.

Can you advise which security panel would be suitable to replace one which has failed? (only lasted 15 years, but sadly now defunct!) This unit has 6 zones (hard-wired) of which I use 4. Anything that offers similar, at least 4 hard-wired + radio to cover areas not currently covered would do. Can you suggest something? I can install it.

I am considering replacing my current alarm system, it has been installed for 20 years and it doesn't suit our needs anymore. I am looking for a recomendation for a system with the following requirements: Blank Control Panel 2 x Remote Keypads 5 x PIR sensors 2 X Door Contacts 1 x Smoke Detector 1 x external bell box I intend to replace batteries and cabling

currently have a Scantronic 9452 alarm system that is going off at random times when not activated. When activated the alarm goes off and the tamper light is flashing even though the alarm has not been tampered with. Also the service and fault light flash intermittently.

I can't find any Wired Siren for my Powermax Complete alarm. Do you have one, or could you recommend one?

Hi guys, just a quickie. Can you tell if the the Visonic Powermax+ Quickfit Kit (inc Wireless sounder)kit has the dialler built in? Can you set and unset via your telephone after an activation and can it send you a text message to let you know when the alarm is set/unset? I can't find any spec online fort his product. If you could email me a link that would be just as good. Have a good evening. Dan.

I would like to get the equivalent speech dialler but a digital one, Can you advise which speech dialler would be best?

I think before - the best way to protect a window was to have a foil running around the glass.. Now I see a lot of electronic gadgets. However I am not sure how reliable they are. Say vibration sensor. I guess it is easy to cut glass above/below such a sensor with diamond cutter and simply disconnect it with a knife or undo latches and open window slowly or get through not disturbing the sensor using the hole... I mean - if the intruder is an idiot and will smash the window with a brick it works but otherwise - unlikely... am I right? is there other means to protect glass area? If the window is obscure and design and beauty considerations arent important - is …

I am interested in a small home alarm with following function: Hybrid base unit with backup battery and communicator that can send alarm to my cellphone trough GSM mobile phone network, working in Sweden. Remote keypad Tag to set or disarm the alarm I have looked at Honeywell flex and ionEX and Microtech Galaxy 2-44 Comms C/W Keypad but I do not understand if GSM are integrated or if I have to buy it separately?

Do you stock Honeywell ECO1002A smoke detector for adding to Honeywell control panels?