Intruder Alarms

Hello, My question to you is, do you sell 868 or 433 Mhz. recevers and transmitters (detectors) of the risco gardtec eurosec CPX range. best regards, C.Boogaard

Hi, I am going to replace my 23 year old system, and wnat to know if you sella kit, with : a control pane and key pad, and internal siren, an external siren, 3 pir sensors, wired, 5 wireless door sensors please ? How much, if you do, and do you have brown door sensors ? Then, how difficult is it to set the wireless sensors up please ? Cheers. Alan.

Can you suggest a package to provide 3 x independently switchable on/off beams of 12m, 9m, 6m span with a control panel and sounder. The sounder to mute after a preset time. the system to be mains/ 12v powered. The detectors to be preferably powered from one end only of each beam. As cheap as possible, p.s. external use near the ocean.

I need 2no wired zones aswell as the wireless ones. will the expander for the Powermaster 30 work or do i need the 8 zone expander?

hi, I am interested in purchasing a number of wireless intruder alarms. i was looking at some systems on your web page but i am unsure as to which best suits my needs. i wish to install wireless intruder alarms in 6 domestic houses. these systems do not need to be monitored by telephone line. i am looken for: 6 wirefree security alarm panels (no less than 30 zone) 6 wirefree external sounders 5 wirefree remote keypads 107 wirefree magnetic contacts can you let me know what kind of system would best suit my needs and a quotation for the overall cost. i am living in the west of ireland. will this effect delivery costs? if so can you include this in the q…

Hi, I received delivery of the MCS-710 a week ago. Upon installation the test button sounds the siren after 5 seconds, but it will not enrol with the Visonic Powermax base. There does not appear to be any wireless transmission. Regards

I ALREADY HAVE A VERITAS 8C SECURITY PANEL FITTED AND EVERYTHING WORKS FINE APART FROM THE BUTTONS. THE NUMBERS HAVE ALMOST RUBBED OFF AND SOME BUTTONS ARE NOT FUNCTIONING PROPERLY WHEN BEING PRESSED. MY QUESTION IS ...IF I PURCHASE A NEW VERITAS 8C PANEL FROM YOU CAN I USE THE FRONT PART OF THE NEW PANEL TOGETHER WITH THE BUTTONS TO REPLACE THE OLD FRONT.

Hi I ahve just purcahsed a Eurosec CP8L panel and a Pyronix Databell Plus Bell box, and would like you to confirm connections as this configuration is not listed in the manauls CP8L Bell+ Bell- Bell HO Strobe + Strove - SAB Tamper In the bell T T STB BELL 12v+ 12v- In addition is it possible to configure PGM1 to give 0v in Engineer mode to disable the bell box tamper. Various settings sre listed but not this one. Any advice apprecaited

Hi, re the above system, can this be operated by remote control or can I somehow link it to a remote garage door opener? Alternatively, is there a system that can do this?

I have an old ADE Karizma iD system I would like to replace. Do you have iD systems in stock...?

We are looking to put together a scaffold alarm using dual beam sensors possibly 6 sets with a control panel and auto dialler. What can you suggest please?

Hi, I bought a sensor scantronic 714REUR but i not able to associate with the central Homelink 75. I followed the steps in the manual: enter the menu to acquire the unit and then trigger the tamper on the sensor. The red activity led flashes regularly but not response from central. Other sensor i bought (738REUR) work correctly Thanks Stefano

I have a set of garages with two alarms installed that both join to a single masterblaster in the roof. I want a dialer that rings me or another member of the family if the alarm is triggered or the power is cut on the system. Sorry, I'm not very technical, but can the GSM dialer be connected in the roof space on the same wires as the masterblaster? Obviously the masterblaster will not work if the power goes down and so I wanted an autodialler as a back up. If so how much wiring would be needed and is it straight forward?

Hey there alarm been working fine an come home to the keypad display as follows Accenta G4 RKP F131-01-111 No lights on lcd keypad and no response from keypad been working fine for a year can send pics if it helps

Hello. Do you have an Intellisense IQ260 replacement/equivalent please. I have one in my garage, after doing some refurbishment to the building I was thinking of installing an additional sensor as a single one can no longer cover the area. That is if 2 pir's be installed in the same zone/room? an 8 core cable is installed however only 1 core remains unused. If 2 can be used on same cable maybe better to buy two identical detectors and do away with the IQ260? Thank you.

I purchased a Honeywell Accenta Metal Gen4 Control Panel and Viper GLX Shock Sensors from you a couple of years ago (Order #16133). I am only getting around to installing the alarm system now and I have a query which I hope you can answer. Before I bought the house, part of the house had already been pre-wired with 4-core alarm cable. One of the pre-wired zones at the rear of the house is wired with 4-core cable and the sensor points are linked in series, i.e. the alarm circuit and tamper circuit are both linked in series. The cables to each sensor are connected under a tiled floor, so the junction box is impossible to access without breaking tiles. As the sensor loca…

Hi, the last 2 kits I have ordered, ive got a problem with a white door contact, stuck on reed switch. and a Honeywell PIR that keeps flashing and not picking up and detection please can you advise many thanks

Galaxy RSS software and Management Suite. Wants to know the difference.

I ordered the above Visonic MCR-304 Receiver from you and it was quickly delivered without any sign of transit damage. Firstly my thanks for your prompt service. I installed the item in the prescribed way and powered it up. I then set the Learn jumper into the Learn mode and the yellow LED flashed as expected. I then pressed the Tamper spring and the yellow LED and the red LED both flashed OK and using the tamper key I was able to cycle through the various channels. I then tried to associate/enroll a known good transmitter and in this respect I used a MCT-100. This transmitter was free standing and located close to the MCR-304 so range was not an issue. I tried to force …

Which key fob is the right one for the Galaxy keyprox keypad and what are the grey fobs for?

bought a complete system buy you. Now I have a configuration issue. The alarm triggers directly when I enter, now entry delay is active. I have chosen 1. Exit/entry delay 1 for door contact and 3. home e/e for motion sensor in hallway. Is this correct? I want to be able to have Home zone active without triggering the alarm (except when door is opened). Should I choose antoher zone type for motion sensor in hallway?

Can the Galaxy Flex 20 alert me directly via PSTN or the optional GSM board, or can it only signal to an ARC?

Recently installation of a galaxy flex and looking to put Ethernet module A083-00-01 into it On looking at the other flex systems they are all in plastic boxes with the RF Portal as a seperate card inside this flex is in a metal box. Honeywell Flex 20 Small Metal Box- C005-S-E1 & as seperate RF Portal -C079-2 Does anyone know if the Ethernet module can be used within this flex? Thanks

we are searching for Flush mount type magnetic contact EN 50131-2-6 compliant, Grade 3 type do you have any?

I've bought a Visonic keypad KP-160 PG2. According to the manual, it should be possible to use an optional power source (5-12V DC) instead of batteries. Where can I buy such a power supply? Thanks