Intruder Alarms

Which cable is best to use for the Comm's network ie Galaxy Panel to Keypads and to RIO's?

check outputs? can anyone help me make sure i set it up right and what to check/fix i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the extern…

Hi i have the Accenta 8 mini. and the keypad is about dead. i am thinking of getting the keyfob. I got a few questions regarding it My keypad is situated on my stairs. and i am going to install the keyfob at the bottom of the stairs. or do the keyfobs have to be on the outside.. Could i connect the Easy set Key fob. whilst the alarm is still plugged in.. As i carnt remember how to set the alarm into diagnose mode so i can open the panel so the alarm dont go off. I installed it like 3 1/2 year ago and cant find the book for it.. any help will be great Thanks

Hello! I'm about to order the following items and I'd like to know if the batteries are included or not; in case I need batteries could you please tell me which type? ADM-DOM-SI - Domonial Wireless Internal Sounder KTC 805 - Honeywell Domonial Keyfob DO800M - Honeywell Domonial Radio Door Contact Thank you very much!

Hi, I self-installed a Euro Mini about a year ago. I have two keypads installed, one upstairs and one downstairs. It's been working fine since I installed it but now its giving me error 485 COMMNS LOST. Neither of the keypads respond. If I open the panel box or the keypad to fault find, the tamper alarm will sound and I have now way of overriding it! 1. Any ideas what would cause this problem (error 485)? Does the keypad or panel have a keypad fuse? If so would a blown fuse cause this error? 2. Without a working keypad, how do I override the tamper alarm? Thanks in advance.

I have not seen any on securitywarehouse product page but do anyone know of any other site where I can get normally open surface contact. are these passive or active(need power to work?) thanks

I have purchased a belle and two twin alerts by pynonix (order no 33462) to install on a scantronic 9752 panel. Neither the scantronic nor either belle/twinalert manuals match each other so would like some guidance on wiring these up. The scantronic manual has the following output:NO1, NO2, Tr, 12V AUX and 0V, and a separate +, and LS for internal loudspeaker. The belle has B-, B+, BA, STB, SPARE, BT and TF, The twin alert has 12V+, 12V-, SPK and BA The belle shows the following connections for scantronic: B+ = 12V B- = 0v BA = BELL STB = STROBE- BT = TR TF = 0V The TwinAlert has: 12V+ = +12V 12V- = 0V SPK = SPKR (low) BA = BELL The s…

Hi, I'm looking for the firmware update 6.50 on SPI Key "SOF-096-E1-650" for the GD96 released in Feb. Will you have this available at some point, as it enables the RF keyfobs ?

Hi, Our alarm has been giving us problems for about 2 weeks. It indicates an intermittent problem with the PA and low battery - the alarm goes off intermittently as well. we have changed the battery in the main control panel and the PA. We have inherited this system and have done nothing with it apart from keeping the PA to hand (and changing the batteries), it has never been armed. What advice can you give? We would be happy to disconnect the thing and switch it off completely - but when I try (by removing the fuse) the outside alarm goes off. Please help - it is driving us nuts especially during the night when it goes off for no reason. One thing - this probl…

Hello, I resently puschased a PowerMater 10 alarm system from you and am now starting to install the equipment. There is a problem with the display on the master unit, it seems like it doesnt remove some of the characters and some texts looks really weird. For example, int the start screen it says "15:16EADY : " where i guess it should say "15:16 : READY ". If I have a fault it switches between "NOT READY TRBL" and "15:16EADY : " There are also some really strange characters for the zone naming when I try to add equipment to the system. Everything else seems to be working though, I can add equipment and arm/disarm the system. I have tried doing a "Factor…

I purchased an alarm system last year, and until today has worked without fault, however, when my Wife tried to set our alarm in the usual way using the ADE Simple Set she was unable to do so. When I came home I also tried without success. The unit shows both Power & Day lights but when either a 'learnt' or an 'unlearnt' fob is offered to the unit there is no response regardless of the length of time the fob is held against the unit. Any advice would be greatly appreciated. The unit is less than 12 months old

Hi Experts I am looking for alarm system for my house having (preferably Free App mainly to disarm the system if its false alarm from Remote location) Area needs covering are sensors covering 1 Main Door Sensor 1 Sensor /Shock Sensor for Patio 4 Sensors covering (1 on Landing,1 sensor in Kitchens area,1 for living room ,1 sensor for garage) 1 or 2 Sounders off excellent build quality preferably with blinking LED. My preference is Wireless as house is new build (But can think of Sounder being Wired if its good to do so rest of all sensors being wireless) So far i have done some research and found Visoic PowerMaster 33 or 360R …

Attached is a wiring diagram for 'Double Pole', 'EOL' and using a Risco Guardtec CPX 'Zone Doubling' Conventional Double pole requires a pair for each part of the detection device, ie 'Alarm' and 'Tamper'. Wiring the Tamper Circuit as double pole will require a global tamper, this means that all devices with tamper protection are wired in series into the tamper connections of the control panel. Zone wiring is then wired normally straight into the relevant zone connection. This has the advantage of being simpler to understand, but has the disadvantage of a global tamper, ie being able to identify the device in tamper is impossible. Lower end panels only offer Double Po…

Hi all, I have a Texecom Premier 48, to which I am trying to use the Wintex software to program. I am attempting to use my PC modem to connect to the 2400 com modem installed on the panel. However I can not get a connection with my PC to the panel. Has anybody had issues when trying to do this? Thanks.

Hi There, I would like to use the Clip MCW PIR detector by Powermax with the Scantronic RFX08 radio receiver. The frequencies are compatible but will the two units communicate properly.

We recently bought some pendant transmitters from you for a Powermax+ Alarm system. I sucessfully installed 1 of them (more by accident I think) but am struggling to make the other work. I find the instructions very confusing! Please can you help...

Is the Honeywell 12v non latching detector base a NO or NC?

Hi, Just bought from you a visonic powermaster 30 kit with some additional modules and sensores and have the following questions : 1) The Next PG2 K9 motion sensor come with 2 lens, what is the lens that is Pet tolerant? 2) I would like to buy a RS232 module to connect to the powermaster using the "Remote Programmer PC Software". Two questions : 2.a) What is the RS232 module that it's compatible with the powermaster 30? 2.Do you supply also the "Remote Programmer PC Software" ?

Do the Honeywell sensors, external siren and tag reader with built-in siren communicate over encrypted rolling code? Do these - FG8M, DFS8M, CO8M, IR8M, IRPI8M, DO8M, SEF8M and SPR-S8EZ, etc. I know the fobs and panic buttons do. These do - TCC800M, TCPA1B, etc. I am using the Honeywell Evohome Security at the moment, that uses the Le Sucre+ box. Is the Le Sucre+ box and the SPR-S8EZ grade 2 EN50131, if they are not grade 2 EN50131 is the dominion a better control panel to use instead? I know the sensors, external siren, fobs and panic buttons are grade 2 EN50131.

Hi, I purchased the above kit from yourselves just over a week ago. I am trying to wire the bellbox to the control panel, however, the connections listed in the Intellisense AG6 leaflet differ from those on the actual PCB. The manual lists TR- V- ST- V+ S- but the PCB has ST R SW V+ V- So can you tell me what to connect to where on the Accenta G4 panel? Regards, Warren

support/Elaine, is the 2.1Ah rechargeable battery included with 9448EUR-95 STYLE? thanks

Hi, How do you change user and engineer code to the Texecom premier 24 panels. The manual gives details to change from eighter 4,5 or 6 numbers. I have tried with no success to program with 4 numbers and won't except only if I use 6 digit. Please if any one can help I would be grateful as I don't want to use 6 digit. Thanks.

I've got the issue with ADE Honeywell Easy Set bought from you about 2 years ago. It requires resetting(cutting the power off) at least twice a year. Is it a known issue with these? Basically the keyfobs stop functioning and reset always helps when it happen.

Hi! I have previously purchased Visonic PowerMaster 10 Panel with Visonic PowerG KP-160 White Touch Screen Arming Station c/wProx. I wonder which Wireless Keyfob Transmitter would work with the current setup so that I could control the alarm from a distance?

Installed a new Galaxy Flex 20 with mk8 keypad and a couple of RF zones. Had some previous issue with the tampers and low battery in a few PIRs but that has been sorted now. I have a new 7.2Ah battery fully charged. Problem is when I set the alarm I get this "ALERT-BATT LOW", ent=CONTINUE SET on the panel, and then after pressing enter "ALERT-FAULT RST" ent=CONTINUE SET. So I can set the system by ignoring these error, but what are these errors coming from and how to get rid of them?