Intruder Alarms

can you tell me dose the snt duolink kit come with psu

Can you tell me if there is any benefit to having an mcs-730 over a mcs-710 other than being 10db louder?

Hi I need to default and reprogram an Avanti LC 8 zone alarm panel, it has an LED remote keypad and plastic end station. Building has been empty for some time and it was completely powered down. We have no record of any of the previous codes....anyone got an installation manual please?

i am after a scan 9943 with 5 or 6 remotes. Will the keypad pair up ok with a 9930. How much is a 9941 & 9943 & fobs

HI, Should the KP-250 keypad play sounds? I can hear beeps when i press buttons however there is no count down when the alarm is setting, there is no sound when a recorded message is played and there is no chime when the door opens... Am i missing something? i have turned the volume up - the beep gets louder. I have pressed 8 and the alert(bell) icon is lit and the chime is set to on and melody chime. Do i need another speaker installing or is my keypad faulty? Thanks in advance

Hi, I'm looking for the firmware update 6.50 on SPI Key "SOF-096-E1-650" for the GD96 released in Feb. Will you have this available at some point, as it enables the RF keyfobs ?

The chime that comes from the KP250 keypad is pitiful, even on max setting its only just audible if your in front of it. I cant see anything in the documentation that says the indoor siren can be used as as a chime speaker. Please can someone confirm if this is possible?

Hello could you please help me with how i would wire the The 12 Volt Relay Base, 45681-508 to aTexecom PREMIER ELITE 48 8 ZONE CONTROL PANEL please

We moved into our house previously without pets but with one of the above alarm panels. I need to replace three PIR with pet friendly ones. You advertise the Scantronic 430, is this compatible with the 9450 panel. Also I wanted to install a dialler but it seems that you are out of stock of all diallers. If there is one that is compatible with my control panel could you please let me know. Also I would like a clue as to how to wire up the dialler to my panel.

We moved into our house previously without pets but with one of the above alarm panels. I need to replace three PIR with pet friendly ones. You advertise the Scantronic 430, is this compatible with the 9450 panel. Also I wanted to install a dialler but it seems that you are out of stock of all diallers. If there is one that is compatible with my control panel could you please let me know. Also I would like a clue as to how to wire up the dialler to my panel. Please feel free to answer any one of the points. The main one being compatibility.

Hi, I was wondering if anyone could help me decide on a simple & effective alarm system. What I need is listed below. 1) 1 door contact 2) Minimum 2 PIR's (wired or not) 3) Key fob to de/activate alarm 4) Some sort of notification on activation (email, text/call) 5) camera that can record images/video when there is motion and the ability to send the images to a phone AND be viewable over the internet Ideally, I'd like the system to be controllable remotely and have as little wiring as possible. I have made allowance for 2 cat5 cables to the 2 known Camera/PIR locations. (Depending on the cost, I might also include a door peephole camera - again, I'…

i have a client with a texecom 48 and wants some smoke detectors now some people say run alarm cable but i would of thought it be better to use the red fire rated cable?

I’ve got a customer who wants a zone removing and an extra door contact adding to an existing hardwired system. Is there an converter or interface panel that can sit aside the control box and run a wireless zone? Any advice would be welcome.

looking for compatible door sensors, keypad and key fobs. have noticed that the key fob is sold out

currently have a Scantronic 9452 alarm system that is going off at random times when not activated. When activated the alarm goes off and the tamper light is flashing even though the alarm has not been tampered with. Also the service and fault light flash intermittently.

Hi all, I have just purchased the MCM-140+ keypad for use with an standard Powermax Alarm. When the alarm is in Enroll Keyfob mode and I press the * for two seconds, the alarm does not recognise the keypad. I have just re-enrolled all other sensors and a keyfob without any problems. Any ideas? Many thanks, Paul

hi i have just installed this panel to an exsisting system, it has 1 door entry contact and 2 pirs 1 on the route to the panel the other at the back of the house. i conected the door contact to zone 1 the pir on route to the panel on zone2 and the other to zone 3 i am using program 1 and set zone 2 as timed inhibit the problem im having is when i do a walk test zone 1 triggers zone 3 and visa versa zone 2 triggers on its own fine. so if i set the alarm as i trigger the door contact (zone 1)before i get to the panel the alarm activates so i enter the code to silence and zone 1 & 2 are solid and 3 is flashing the door contact is only 2 wir so i cant have wired it…

Hi, will the UTC GS711 - Shock sensor with magnetic contact work with a Siemens SPC system? Or do you have any suggestion on a sensor for a SPC system that have both magnetic contact and shock sensor?

I wish to buy pir for above alarm can you tell me which is the right pir for this alarm

I am looking to replace my current alarm system with a new modern system. One of my main requirements is to allow remote access to the system, and so I am looking at the Scantronic i-on 40. Although all of my sensors are wired the wireless capability will be handy if I have to upgrade in the future. I also require SMS messaging through GSM and PSTN so would be looking to also install these modules as well as one extra wireless keypad. My main concern at the moment is how the wired sensors and PIRs are connected to the i-on 40 system to ensure it will work with my current installation. Can you provide any information as to how the zones are wired on the system, or are …

The unit we received is a EE1215W Universal transmitter. We need to look at getting a receiver for it. The switch we have generates a wireless signal that has to go back to something to then make the actual switch. All we have is the transmitter. I would need to install a receiver into our product in order to make it switch on and off

Hi I purchased a security panel, Texecom Premier DC8 + a few years ago from yourselves and I am only just fitting it but have mislaid the remote key pad and installation instructions. Can you advise which remote keypads you sell that will fit this panel as I note it is not for sale any more. Also, do you have the installation instructions available? Thanks

I am after a vibration sensor to fit to my roller shutter garage door to detect attempted forcing of the door. Do you have any products that detect vibration to the door itself rather than the frame: concerned that a frame mounted sensor may not be sensitive enough. Standard wired honeywell Optima alarm panel.

What is the difference between Texecom Premier TD-W and GJD D-Tect X wireless? Are they both intended to perform the same job? Is there any drawback for Texecom product compared to the GJD one? How can i choose between these two?

hi i have a job for an alarm system in a barn with no heating and damp/sub zero temps. the barn has two doors one sliding and one side entrance/fire ext. it has mains electric for power supply. also want a gsm dialer for the system. i cannot find a system that will be ok with the damp conditions. please advise, kind regards