Intruder Alarms

Hi, The Castle care tech Euro One 44 (including LCD keypad) listed on your site at

Hi, I have just bought from you the Honeywell galaxy g2-12 and mk7 keypad, Honeywell 8IR150 pirs and AG6 bell box, plus Knight G2 5 door contacts. Can you please advise how to wire a pir at the pir end and panel end and where to place resistors. The g2-12 to keypad appears straightforward but does it need a resistor at the keypad end between A and B. Also do all unused zones need a resistor across them to terminate. Could you also confirm bellbox wiring to panel.

diy er order no#6419. have system installed and seems ok but not fully tested yet! in the absence of the installation manual could you help with some zone terminology. monitor, Ln fault and fault....then normal ky, bias ky, remove+ and remove-. I wish to have it set up for just "normal" pir detection. nearly there thanks...

I have recently purchased 2 x Honeywell Combination Optical / Thermal Smoke Detector (58

Bought myself a Jablotron JA-83 panel. The manual advises to connect only 1 wired keypad (JA-81E). Additinional keypads should be connected wireless. Does anyone have an idea why ? Is this panel not able to work with 2 keypads on the same keypad connectors? Does the panel delivers not enough power to feed more than 1 keypad? Or does Jablotron likes to sell wireless keypads above wired ? I really would like to know why...

I require a standalone wireless receiver plus 2 IR room sensor to connect to an ADC type panel (wire to existing sensors has been cut by flooring contractor)... The Nova 2 would appear to fit the bill?

Hi, I've just installed a Scantronic Homelink55 and the hardwired side of this has worked perfectly straight away. However the wireless side has proved more problematic ? I am tring to 'link' the RFX16 unit with 2 x 703r transmitters, I can get the reciever into learn mode, either -- flashing for the sysetm to allocate the channel or, for instance with 09 flashing (I have configured it to addres from zone 09 onwards). I have the 703r set to have the Ln set to E -enabled; however, with 12v connected the green nlight is on but unless I change the oP there is no activity from the RED LED!! I've tried marrying the both 703rs and have tried both connected to the panel bus …

Is the Secware 12v 2.2A/h Value Alarm Battery (product number 70/118) suitable for the above control panel? Is it normal for this battery to require replacing after 5 years?

Hi, just bought one of these, does anyone know the default Username and Password to enable me to gain access to the panel via its web interface? Ta.

We have had a few enquiries about how to install a door contact to a frameless glass door. I dont currently know of a single product, as an installer it would be usual to build up the contact based on the individual door for example

many thanks recieved panic alarm fob today i recieved the 727r/728r i have registered te key fob to the alarm scantronic ion 16....however it does not arm or disarm the alarm i was wonderng if i had not done any thing obvious i also tried to add it as panic alarm that did not work. i was wondering if it could a faulty fob?

I have a PowerMAx complete wireless alarm system installed in the house. I was wanting to add an additional wireless siren (the system can handle a maximum of 2). I already have the MCS -740 wireless alarm and was hoping to purchase the wired version of this alarm, the MCS-730AC. Can you check for system compatibility. The version number of the panel is: JS702159 B.17.107 JS700421 V.1.0.02

I have your verutas 8 and i have just added another remote key pad, all works fine but i cant seem to get out of engineers mode, i go to program and put my new code in but when it comes to full alarm it will only respond to 4 3 2 1 any surgestions?

Do you sell the delta bell without covers? and is the Delta bell the back lit LED version.

Hello! I have bought a nice second hand DSC wired panel (PC1864) and is looking for some detectors. I am among other things considering the https://www.securitywarehouse.co.uk/catalog/rokonet-shocktec-with-magnet-white-p-620.html As I understand it this unit does not require any external analyzer card or anything and should work as any stand alone wired detector with my DSC right? I am thinking on using it for the doors on my house - do the main part of the detector in this case need to be mounted on the door itself or will it detect vibrations from break ins even if mounted on the frame? Do this unit have space internally to mount resistor? Do you have some install…

I would like to know if you can help me specify a new system based on the Galaxy Dimension. I need it to be able to control 4 doors using mag locks / press to release. Video door entry integration and also intruder function. Proxy tag / swipe for enable/diable of the building alarm. I think I need a Galaxy Dimension GD-48 but need help with the other parts. You seem to be the best value and I need to make a purchase by next week at the latest.

My system is showing a fault "Telecommand Batt Low" which refers to the 723r Telecmmand remote setting device. I have changed the batteries in the 3 telecommand devices I have however the system continues to show the error. I have moved the system into Engineer mode and it will not now exit. Going through the command set to exit Engineer Mode ie 99 tick, the systems goes through the "checking system bus" bit ok and after agreeing to "exit eng" the unit starts the "Checking System" routine and then flags up the "Telecommand Batt Low" problem again and will exit the Engineer Mode. How do I get out of this, as I say I have put new batteries in the remotes but this does not …

I have just purchased the rs232 remote programmer but it is saying that I need to enter installer mode to access this. The main reason I bought the pack was because I could not get the installer option on the menu and I have forgotted the installer code. I have already tried a master reset but to no avail. Please could you advise if you are able to assist.

Hi I would be interested in buying Visonic alarm system. However I am not clear on the PowerLink functionality. Do I have to have Visonic IPMP server installed separately to support PowerLink for exactly this: sending emails/MMS messages with pictures from connected cameras UPON alarm trigger.

I just purchased from you the homelink 75 alarm system. I would like to purchased alarm box to put on the side of my house and operated the alarm system when we are upstairs at night. Please could you let me know which equipment I need to buy, thank you.

Hi I need to replace my current wired alarm system.. I have a mains wired alarm with wired connections. I have a couple of PIR's that are wired, which I see no reason to replace as the cables are hidden. I would like to add additional pirs wireless. I can see execom Kit 3 32 Zone Self-Contained Wireless Kit which looks like it can take 4 wired zones. So I could install this on my current set-up and add wirless pir's to additional rooms. I have a couple of questions. How is the alarm disabled. Is it on the control panel? I see it comes with 2xPremier Elite SmartKey. What exactly is this? Can this disable the alarm without having to put in a code? I have 2 children which I …

Good morning, I am after some advice if I may please. I have a Galaxy Flex100 panel and we want to link up TWO touch centres to it. I believe on a standard panel we can only use one touchcentre. Is there any expansion modules or similar we can use so that both Touch Centres can be used on the system? Any advice greatly appreciated. Many thanks Neil Fearnley

I would like to install a burglar alarm in a clients workshops! They already have Hikvision cctv system and proximity alarms and electronic gate which are the better alarms. I was looking at Pyronix or Ajax but I saw a comment from your store on a forum saying Pyronix were a little limiting are Texecom better Ajax are more expensive!!! Please give advise!

I'm looking to buy some visonic k980 wired pir's can't seem to find them on your site. Do you sell them? and at what price?

Hi, I’m looking to buy a Visonic alarm system. Can you tell me what the difference is between the Visonic PowerMax complete kit and the Visonic PowerMax standard complete kit ? Secondly, I would be installing a gsm unit in the control panel as there is no landline in the house, which unit is best for the PowerMax complete system ?