Intruder Alarms

The chime that comes from the KP250 keypad is pitiful, even on max setting its only just audible if your in front of it. I cant see anything in the documentation that says the indoor siren can be used as as a chime speaker. Please can someone confirm if this is possible?

I need Reed switch for a motorized door shutter to detect if it is closed properly. What model do you suggest?

I also need a manual on how to program GJD wireless PIR's to the reciever. I bought them from you a while ago but the receiver has lost it programming.

Hi my home has been fitted with a scantronic 9651 system, it has p.i.rs in all down stairs rooms. The front and rear doors have surface mounted contacts. When I set the system and leave via my front door the alarm continues to beep and will not arm once I close the door. This has happened before and I was advised to replace the door contact which i did, this solved the problem until now! The same thing has happened again I have checked the contact and everything seems to be OK with no loose wires. The contact is grade 2 with a small circuit board inside, it also has a small spring tamper mechanism. Can anyone help? regards Steve

I'm looking to replace a Scantronic 9853. Would the Eaton I-On interface with the existing PIR's etc? what the most suitable replacement would be as this panel is not in production now.

I'm looking to buy a Honeywell SS/01 SS/F Simple Set Reader for connection to a new Honeywell Accenta Mini G4 or Optima Compact G4. Is the relay return required from the simple set reader to the panel OR will it operate just using the normal 4 wire Positive, Negative, Sound and Comms?

I’m currently considering renewing my current wired alarm system (9450) and increasing the zones to at least eight, as offered in the Secware ADE LCD Accenta 3x Optex Saver PIR starter kit. I’ll be exchanging the external bell sounder which this kit appears to accommodate all those requirements, I’d also like to exchange my two battery operated smoke sensors to wired units. What can you suggest or recommend any other?

have just installed my new control panel everthing working fine, just won't let me change the four digit code, have gone through the instructions given in user manual but it still only lets me use the factory set code to set the alarm,could you please give me some advice to correct this problem.

Does the Honeywell AG6 SAB and Cover (Blue Strobe)have led indicators on perm or flashing, to indicate power is there and it is not a dummy box.

Can Honeywell easy set fobs be used with ADE Honeywell Accenta Mini Gen4 system..alone . or is some extra sensor / equipment needed

Hi, i recently ordered some extra window/door sensor and an external siren for my Visonic Power Master 10 ADT Branded alarm. I have added a few sensors in the past with no problems but both door switches and the siren will not communicate with my alarm panel. When I add the device and press the auto-acquire button on the new sensor the panel tells me it is not a compatible device. So i tried entering the 7 digit number and now the panel said it is not registered on the network. Thinking it may be my panel at fault i tried to register them on a neighbours panel with the same results please advise?

Hi, I had some problem getting the SMS work with the service provider here in sweden and therefore I'am thinking about using the internet and try to avoid using an ordinary alarm central. 1 Do you have any equipment I can use to send alarms via internet from my alarm panel? 2 Is there any crude variant where I can let the alarm call my mobile and I can get some status and maybe even control the panel with my mobile phone? Best reg.

My new house was pre-wired for a hard wired alarm which I planned to fit myself. The guy who run the cabling did a good job except he did not wire for contacts on the doors. There is no chance to wire them now as I cannot run cables thrugh the dry wall panels. My solution I think is something like a Homelink 55 I will have 6 PIR, three door contacts, and two RKP's as I have a point upstairs for night setting the system. Can I add a second 9943 RKP to the Homelink 55 ? The Homelink 55 has 6 wired zones which would cover the PIR's. I hope I could use wireless contacts for the rest. Prox tags would also be a nice addition. Grateful for any advic…

I have installed, approx 9 years ago, a scantronic 500r.+ system and have had the remote control stolen during a break in. My fear is they will return. Is it possible replace the control box with a new one in order to make the remote U/S, Or is it possible to disable the remote. I have 4 PIRs one door sensor and a remote key pad. Sorry I have marked this high but having just lost a new car do not wish then to re-visit disble the alarm and clear the rest of the house. Thank you for your time.

I have G4 panel with LED remote keypad.I want to make door chime facility louder, do I need to connect another sounder to rkp or back to main panel? RKP is near door which terminals do I use on rkp and/or G4 panel, I already have extra sounder near main panel, close to back door also set to chime, wired to speaker terminals in main panel but this responds to alarm condition and mirrors rkp sounder when alarm activated but when front or back door is opened then I'm only getting usual beep-bo from rkp.Am I using the right connections in main panel?

Risco Wireless Wisdom Kit 6 Wireless Devices could please send more details for the bell box is it totaly wire free

Please can you advise what speech diallers are compatible with the honeywell galaxy 2 alarms. I'm looking for one that will alert for intruder and a separate alert for fire. Thank you

Can any one tell me is there such a thing as a window contact+vibration sensor combined (hard wired) if so what is it called and who makes it, seems a pity to have to fit both if there is a combined unit. thanks again for all your help

Can you give me a price for the Powermax Pro please? Your web site says 'call for price'.

I have stored a number of items in my cart and I would appreciate some advice as to whether these are all compatible or if there are better alternatives available that would work with the main system. I have a hybrid wired/wireless system with existing PIR's and magnetic contacts in place but I am expanding the system and finally installing the panel. 5 x - Honeywell Four-button compact two-way keyfob 1 x - Honeywell Galaxy Flex 50 Panel with MK8 Keyprox 1 x - Microtech Galaxy MK8 Keyprox LCD Keypad 4 x - Honeywell Wireless Dualtec 15m x 18m Pet Immune 5 x - Honeywell Galaxy ASK Keyprox Proximity FOB 1 x - Honeywell Galaxy / Dimension Boxed Power Supply Unit 4 x - Ho…

Which battery do i need to order?

Hi, I'm looking for the firmware update 6.50 on SPI Key "SOF-096-E1-650" for the GD96 released in Feb. Will you have this available at some point, as it enables the RF keyfobs ?

Could you please advice on best pet friendly pir sensors

Can you help with my optima compact 8ep 396a? When setting the alarm i cannot set a program ie part set( prog 2 ) it defaults to prog 1.

My installation went fine and system has been working fine for 2 months now. Yesterday we had a power cut and the alarm went off immediately. On investigation I found that the battery fuse was blown and that the charging circuit was generating no voltage at all. This means voltage from the supply side of the fuse holder is not present. The low voltage AC supply from the transformer is ok. If I put in a new fuse ( all I have at home is 1A ) and then connect up the battery the fuse blows immediately. The open circuit voltage on the battery is around 12.5 volts and I imagine that is the charge it had when I bought it. The battery is not a short circuit . If I ignore the …