Intruder Alarms

Hello I have managed to obtain a copy of Wintex(v5) and the Veritas UDL. I've read that Wintex can also allow the programming of the veritas excel. Is this true? I can't find the option under "account" that allows you to choose a veritas; the list just has the premier systems... With the Veritas UDL am I required to buy a texecom PC-COM? Can't I just make my own RS232 using the tx rx and 0v (pinout 2 3 5 on the rs232) Can you please tell me whether or not I can build my own cable?

Hi, I have just finished fitting a Honeywell Accenta Mini G4 with LCD control panel system to my house. I have got to the point of powering the system up and setting it up. The manual says "check that the factory fitted links are connected to the terminals PA, TAMP and T-A. I have fitted it to PA, the TAMP connections are being used for the other sensors on the system, and the T-A terminals are wired to the Bell Box. I then connect the mains power and the battery. The manual says there should be an audible indication, which there is. The 'power' light on the G4 main unit illuminates. The LCD keypad lights up and displays "Accenta G4 RKP F131-01-111". The 'power'…

Is it possible to change the English language of the Galaxy panels into the Dutch language? Maybe by flashing the prom? Thanks in advance for your help. Marc

Hi, I'm looking for some advice, my domestic alarm died on me early hours the other day, control box has gone, wont power on at all. I'm looking to replace it, and was thinking about the items below, 1..ADE Honeywell Accenta Poly Gen4 with LCD Keypad 2..ADE Honeywell Informa Speech Dialler I'm planning on using the exisiting PIR's, internal Door Open Sounder and New Texecom external Sounder, I'd like to tie my garage into the alarm system if possible, what would I need? So 3 x questions 1.............Would the above work with what I already have? 2.............We have had a new Wood effect UPVC front door fitted, and the old door sensor is whit…

Hi. I'm after some advice regarding wiring a pyronix belle box to an optima xm alarm panel ,basically which wire go where. Thanking you in anticipation.

What is the differences between the CQR FW/GD04 Communicator (GSM) and the visonic GSM-100? Are there any other gsm-modules that are compatible with the pm+? My pm+ controlpanel is bought in sweden, will I have any problems if I buy any of the gsm-modules you have from UK? Will the sms-messages still be in swedish?

Hi I have a ADE Honeywell Accenta Mini Gen4 with 4 bosch pir

My keypad has given up the ghost with some butons not working so I cannot disable the alarm with the code. I've taken off the keypad and it has 4 wires connected. It looks very simple to replace so is it simply a case of buying a replacement and installing in the same manner? When I reconnect the power and the alarm starts going, I should be able to enter my code and all is back to normal? Or is it more complicated than that? I've been quoted for a replacment & fitting but it seems such a simple job to do yourself. Do I need to be aware of anything else?

My new house was pre-wired for a hard wired alarm which I planned to fit myself. The guy who run the cabling did a good job except he did not wire for contacts on the doors. There is no chance to wire them now as I cannot run cables thrugh the dry wall panels. My solution I think is something like a Homelink 55 I will have 6 PIR, three door contacts, and two RKP's as I have a point upstairs for night setting the system. Can I add a second 9943 RKP to the Homelink 55 ? The Homelink 55 has 6 wired zones which would cover the PIR's. I hope I could use wireless contacts for the rest. Prox tags would also be a nice addition. Grateful for any advic…

You have 2 items listed on your web site from Texecom. TEX-CGC-0001 which is listed as a Speech and Text Dialler at

I have purchased these intems against your order number 22312. I am having problems setting up the receiver to recognise the transmitter. I have teh items to hand, connected and ready to program, The transmitter is set/connected as a mode 6.with the door switch supplied. The receiver however doe's not recognise the the transmitter. Currently it hase the yellow supervision light on with the two red zone lights flashing. Can you please advise a solution, or better still, can we arrange a time when someone can talk me through the set-up? Thanks for help and best regards,

Do you sell a Visonic Powermax Complete Kit?

How do these watches operate pleae. I cannot see any buttons on side, do you press the pad which is the face of the watch? Thanks for your help

I have installed the door contact (to replace one that ceased to operate). I have followed the "deleting" and "learning" instructions for my 500r panel and acheived the "double beep" to indicate that the panel has learned the code. However when the panel is "set", although all other sensors set off the alarm when activated, the door sensor does not activate the alarm on door opening or tamper (the led on the sensor does operate). Please advise what my next step should be.

Wondering if the Knight Double Push PA Stainless Steel is a Grade3 or if you have any grade3 buttons in stock? Also, rough idea of P&P (2.1kgs)to Republic of Ireland for 3 PA Buttons 2 Viper GLX 1 Calibration tool

Hi I need to default and reprogram an Avanti LC 8 zone alarm panel, it has an LED remote keypad and plastic end station. Building has been empty for some time and it was completely powered down. We have no record of any of the previous codes....anyone got an installation manual please?

I have a Veritas alarm believed to be the r8 which is around 12 years old and ready for an upgrade. Is it possible to use the lcd keypad as an additional rkp on this unit or do I need to stick with the original keypad with led's? Helps would be appreciated. I don't really want to upgrade the main pcb etc. Thanks.

Which hardwired detectors (PIR-movement detector, magnetic contact, siren, smoke detector and siren) are compatible with the powermax+ unit?

Am i right in thinking the internal sounder should sound along with the external when the alarm is triggerd? since mine doesnt, all it seems to do is the chime facility. daniel

I have the Honeywell ADE LCD Accenta 4 x Pet PIR Starter Kit, when looking at the instructions, it say the Tamper network should be series connected, if thats the case why is there no single core wire in the kit?

FIrstly: Iam from Finland do you also ship overhere? Iam looking for wireless door switch system like Visonic. I believe this is good quality system? I have separate home automation system where i would like to integrate this. Can i do it with Receiver MCR-308 8-Output Wireless PowerCode Receiver? I mean if i have 4 door switches and and carbon oxcide detector and maybe some other then i can contact with 8 different sensors to my system? Does this unit include already relay to make conatact for 24VDC system? Can you provide such relay if its not included? How much its cost? Iam also looking for RFID system with single relay output 24VDC and some 8 tags. This would nee…

I am about to place an order for a Scantronic 9651EN-41 (9651 c/w 9941 rkp)with a remote keypad and tags etc. You do not seem to have a Scantronic external sounder. Are all the sounders you have of othr makes compatible with this control panel?

hi there can you please help asap i have got a pyronix bell box off you and a veritas alarm system i have installed it for my costumer and every thing works except when the alarm goes off the bell box does not the strobe works and when you take off the front of the bell box it stets off the alarm and works it self .

can you confirm that this includes the external sounder and gsm module? if so sold!

Re products: ESP Quest 14m PIR & Honeywell Intellisense IS215T 12m PIR. Can you please confirm price of these items and which produce would be more suitable for residential use. Is the ESP as good a quality as the Honeywell PIR. Could you also recommend a suitable control box (alarm) and entry keypad that would be compatible with these PIRs. Thank you.