Intruder Alarms

I have an existing system with a Scantronic 500+ control panel but have no instruction manual. I know the access code but I don't know the engineers code or anything else about it. I have replaced all the batteries in the system but have triggered the Tamper alarm and I don't know how to reset this. If I replace the existing control panel with a new 500+ then: 1. Can I programme this with my own engineer code and entry code ? 2. Can I use my existing PIR's (Type 520r) and keypad (Type524r) ? 3. Does the instruction manual contain all the information I need to do the above ? 4. Is there a simpler solution to my problem ? Thanks in anticipation of some good advi…

I would like to order some Bosch Blue Line ISM-BLD1 TriTech Blueline Detector. These are available in three frequencies. I'm interested in the 10.525 GHz ISM-BLD1- F1 model. Would you able to supply this model ?

How do you loop wire two Honeywell Intellisense IS215TCE PIRs into one zone when using a ADE Honeywell Accenta Metal Gen4 control panel?

In november i bought a texecom bell box off you and its just stopped working. the rest of the alarm is functioning fine. when enter the eng code, the 05,54321 to test the sounders everything except the bell box works. it was working fine, so could i return it please unless you can suggest something to try? all the wires inside are firmly connected.

I ALREADY HAVE A VERITAS 8C SECURITY PANEL FITTED AND EVERYTHING WORKS FINE APART FROM THE BUTTONS. THE NUMBERS HAVE ALMOST RUBBED OFF AND SOME BUTTONS ARE NOT FUNCTIONING PROPERLY WHEN BEING PRESSED. MY QUESTION IS ...IF I PURCHASE A NEW VERITAS 8C PANEL FROM YOU CAN I USE THE FRONT PART OF THE NEW PANEL TOGETHER WITH THE BUTTONS TO REPLACE THE OLD FRONT.

Hi, I am going to replace my 23 year old system, and wnat to know if you sella kit, with : a control pane and key pad, and internal siren, an external siren, 3 pir sensors, wired, 5 wireless door sensors please ? How much, if you do, and do you have brown door sensors ? Then, how difficult is it to set the wireless sensors up please ? Cheers. Alan.

Risco Wireless Wisdom Kit 6 Wireless Devices could please send more details for the bell box is it totaly wire free

Hello. Interested in installing an alarm system. Such as Electronics Line Infinite Wireless Kit can you tell me if i can change options and replace the PIRs for Door Connectors? Does the external box sound and is this wireless too? Basically what I want is wireless system, 4 Door connectors, outside box, GSM to alert of event.

I have purchased the Powermax+ from you last year. Am redoing the electrics in my place and rolling electrics to my cabin. Was wondering how I can connect my cabin to this alarm. Is there a way of connecting a PIR via a cable?

Hi, I'm interested in purchasing your product 166/173 (Visonic MCM-140). Before I do can you tell me if this is the 868mhz version?

ADE Honeywell Accenta Mini Gen4 with LCD Keypad does this come with an internal speaker? If not, how can i order an Accenta with an internal speaker and LCD remote control panel

I am replacing my old alarm system. I have done some research and it appears Scantronic are a good make in terms of functionality and reliability and come recomended from a colleague who has installed them previously. I have a wired sounder at present and want to maintain the wired asoect if possible. I'm looking at: i-on16 Control Panel (1) 714 Wireless PIR (6) Wireless door contacts - brown (2) Compatible wired sounder or the wireless one for i-on16 Please advise if the above are all compatable and what is my best option for a sounder. Also would the wireless PIR work in my detached garage? It's approximately10 metres from the control panel location.

Just instaled the panel, remote key pad and sounder and pirs. Firstly the instructions didn't match the sounder terminals with the panel but I think I may have sorted it know but the proble I have is as soon as I connect the sounder battery jumper the sounder goes off this happens with the panel wired and powered on fully disconnected from the panel. I have the system up and running if I put itI into alarm I get nothing from the main sounder sound or strobe but the sounder in the remote key pad sounds Please can you help?

Can you help with my optima compact 8ep 396a? When setting the alarm i cannot set a program ie part set( prog 2 ) it defaults to prog 1.

Hi, I'm looking for the firmware update 6.50 on SPI Key "SOF-096-E1-650" for the GD96 released in Feb. Will you have this available at some point, as it enables the RF keyfobs ?

Do you sell the base for the Honeywell Thermal Smoke Detector ECO1002?

Need external apir sensor with dc input, adjustable on/off times, 180 degrees+ range. Which is suitable.

Can you source Elmdene ELM-PA-G3-SS Double Push PA

Would you be able to stock the klaxon H sires value back plate and covers as i have been using this type of external sounder. I would normally order 40 - 50 covers at a time which would be screen printed for free and 20 live plates is this something that you could arrange?

But I wonder about the price for Visonic Powermax Pro? Do you have Visonic Powermax complete as well and if so what's the price for it? If I order two complete alarm systems with accessories, is it possible to get any kind of discount? Do I need to change anything else except the power connection to get it working in Sweden?

I am looking to purchase some CQR FreeWave products and you have the 240v Interface and Keyfobs, but the 3 channel module. Is this something you can source and what is the price please?

Hi, I'm after some advice on my Accenta G4 system, as with most good DIY project a purchased it a few months ago and only reently got round to fitting it (a wedding got in the way). Anyway i've installed it and powered the system up and two issues occur. 1) There is no power on light on the system or the key pad (or any light on any of the sensors). 2) Although the key pad (and alarm) operates (i'm assuming from the battery), when i enter the security code on the kep pad it says tamper lockout. Now i can accept that there may be a tamper fault somewhere but i wondering first whether its all related to the power problem and whether there is perhaps a f…

hi i have a veritas R8 alarm and require a replacement battery could you contact me with the spec that i require as i would like to have the battery prior to opening the controll unit. many thanks.

The Texecom Premier 88 Control Panel (Part No: DBD-0121) contains the User Guide and Master User Guide booklets but not the Installation Guide. Is this available on your site and can you provide me a link to it?

I need some sales support on the purchase of a Scantronic I-ON 40 and accessories. I don't seem to be able to find some of the accessories on your web site and I am unsure what is included with a basic I-ON40. My basic requirement is for the I-ON 40, smoke alarm 720r, Autodialler GJD HY005.