Intruder Alarms

the keypad on my scantronic 7400 alarm system is not working do you have a replacement one in stock and if not do you have anything compatable that could be fitted instead

I need to replace a PIR on my 500r+ system. I've got 515r PIR's and notice you've got 520r PIR's "compatible with 500r+" so it looks like that's a reasonable replacement. Can you confirm that it would be a viable replacement, operates on the same frequency etc.

I'm tring to programme the bell time on this panel in engineering mode. When I press "6", LED's 1,2 and 3 should show but I'm getting 1,3,5 and 7 and then it won't go any further. Does anyone know what this means and why it is happening?

I have semi decieded to purchase/install an MDT alarm system and will be connecting a stand alone autodialler also I have used Texecom speech only recently but am curious if there is an easier to use alternative available? Do all autodiallers require you to record a message during installation or are there variants that come with pre recorded messages? Thanks in advance

Can you please confirm this product is a heavy duty door surface contact, approx. size 20 x 80 x 20mm deep. Also that this product comes as a pair i.e. contact and a magnet.

Please advise if you can supply a replacement PowerMax Plus panel (433 MhZ) to Cyprus?

I have a Gardtec 800 system with an 8 way zone expander unit. After a lightening storm the panel comes up with a fault: LEX1 tamper. I believe this is a line expander unit fault. You are selling a Gardtec 02083 Zone expander unit - is this the same as the line expander unit I have (label with EX MO1/11 EN50131-1 PD 6662 G3 EC2 PR5705 Rev 1.0 4390) I would appreciate your help.

Does the Texecom SPEECH DIALLER Text Alerts system send texts directly i.e. when the intruder has already cut all the BT lines & broadband etc, will it still work - does it have a SIM card?

hi i am after a texecom 24 1xd expansion module, do you sell these as you only show the 60 version

I have a few PowerMax questions that I hope you can help me with: - Which frequency band is PowerMax+ and PowerMaxPro operating at? - How much is it for the PowerMaxPro unit (incl. GSM and Powerlink) together with 2 x keyfobs, 2 x smoke detectors and 2 x motion detectors? - Is it possible to connect a Powerlink and GSM module to to the PowerMax+?

I am tring to select an alarm with the following requirements: Up to 8 zones LCD keypads (1) Proximity tag capability (prefer it built into the keypad) Easy to use Autodialler capability preferred but not essential (can add standalone autodialler) Reasonable cost The panel will be in an obscure location which wont be accessed regulary (no need for buttons) so will be controlled/programmed by remote keypad/fob Please advise which items would be suitable

I am trying to get hold of a morley key fob for working electric gates and access doors in our apartment block. The reader is a Morley TM4 Series. Please can you let me know if you have these in stock or alternatively another key fob that is compatable with the reader. We need 6 key fobs. Thank you

I require a flush door contact to be fitted to a wooden door. Can you please recommend a product? As I am confused by the terms \\\'Grade 3\\\' \\\'Grade 2\\\' and \\\'Green Resistor\\\' \\\'Red Resistor\\\' I will be purchasing the Scantronic 9651 (not sure if that makes a difference)

I am also looking for an internal siren. Would you be able to recommend one suitable for a three bedroom house?

Hi, Can I please ask for some help on choosing a new alarm system for my 4 bed semi house with a garage on the side. The garage has a flat roof and there is a new flat roof extension being built at the back which will give access to 2 bedrooms. I have a living room at the front and a study on one side. The open plan kitchen/diner will have large folding patio doors at the back. The house is being completely gutted so hard wiring is not a problem and I have builders and electrician in at the moment re-wiring the place. I have been told about the Scantronic 9651 and 9751 systems and i would like a bell on the outside with LED lights and a number pad that can be cont…

Is the yussa NP 2.1-12 is the correct battery for the Accenta Mini gen 4 and will it fit within the case of the alarm panel? - prior to confirming an order

i would like to buy a Elmdene Grade 2 Flush Contact do i need to get the one with purple resistors to be compatible with my risco system or would other resistor colors work thanks

Having had a Texecom R8 installed since 1996 the only thing that has now failed is the "5" on the Keypad, so I have replaced the old one with new 2010 version. The swap out has worked fine, but the Red Zone 1 & 3 lamps are on all the time, I have check the wiring and all is OK, and I have done the the scan for Keypads "0 9" from the new keypad, all appears to be OK, but the the Red Zone 1 & 3 lamps remain on (on the keypad) Date stamp on the Main box is also 1996, so is this a backwards compatabity issue with the new keypad and the old main box?

could someone please recommend a backup ower supply suitable for the Risco Gardtec Eurosec CP8L

Does the Scantronic 9651 EN-43 have a proximity remote keypad, if so does it come with any proximity tags included? Thanks

Hi! I can't figure out if the wireless siren MCS 720 are compatible with Visonic PowerMax+ or not? Does MCS720 work with PowerMax+?

my customer has a accentra mini 8 alarm system, the external sounder appears to be faulty. Can you supply a replacemnt sounder. If so can i replace old with new wire for wire without instruction? The existing sounder has security alarm with a man climbing through a window logo on it. hope this helps?

Hi! Bought a Visonic Powermax+ alarm from you and have run into some problems regarding master installer code and installer code. The problems shows on both the central unit and the keypad unit. When I installed the alarm, I (of course) changed the default codes to my own. However, as far as I can remember I only changed 2 codes where off one being the user code and the other one either the master installer or the installer code. Now I can't seem to access the alarm using the other alternative of installer codes. I would be glad if you could give me some hints to where I've gone wrong. The setting and fault behavior right now are as follows: 1. When first changi…

I cant seem to find the following items on your website. 2x Texecom Ricochet Wireless Magnetic Contact -W - GBC-0001 4x Texecom Ricochet Premier Smartkey Wireless Iconic Keyfob 1x Wilress Receiver 32xp Can you source these items?

we would like to fit a wired Alarm system, we have made the following list of items We like the look of the scantronic 9941 box as we would like to put a TSD2 speech dialler on so that we can telephone and check the system remotely. > > We would then like to put a remote keypad in the porch area at the front of the house which we would like to have night set options. We would also like to have a personal attack button and maybe a keyfob to de activate the system. We would like an internal sounder but maybe this is built in to the system. > > We would like a siren and strobe sounder on the front of the building. > > Detection Points > > …