Intruder Alarms

I am looking for motion sensors that sit on my window cill that points out of window and can detect a person outside but only up to a few meters. I would like a buzzer that goes off but not a loud siren. I dont have Wifi for security risks as everything is multiple VLANs via ethernet cables. Can you please recommend what would be suitable to achieve this, Thank you

I have a few G3 Keypads as they are now Obolete can you upgrade with a latter model or do you have to change the pannel also?

I have the Honeywell ADE LCD Accenta 4 x Pet PIR Starter Kit, when looking at the instructions, it say the Tamper network should be series connected, if thats the case why is there no single core wire in the kit?

I need to replace a PIR motion detector for my home alarm system. The sensor that needs replaced has 7 terminals at the top of the circuit board. They are: 12v power +/-, Alarm NC x2, Test x1, Tamper NC x2. Do you sell a detector with the same connections? I tried a Pyronix MeQBlue but it only has 6 terminals (no Test terminal) and also the terminals are at the bottom of the board and not the top ( the cable length and positioning are quite limited). Thanks for your help!

I am working on a project with one of our clients. We are installing Gallagher system for them - https://security.gallagher.com/. One of their requirements is to have wireless sensors on windows connected to the Gallagher system. I was told i could use this Wireless Receiver. But do you know which sensor i could use? For example we have Ajax sensors on hand. Do you have any experience with this type of setup? look forward hearing from you.

Hi, Need confirmation that the set-up I have listed will all work together, we are ex.UK but now live in Crete where we have built a house without, regretably it now turns out, a hard wired alarm capability. Crete, once relatively crime free, has now gone bad ways and recently our neighbours were robbed and they had 6 dogs loose in the garden! So I am looking to buy and install a wireless system sourced from the UK and need clarification it will all work and is foolproof for even me to fit ! Basic I-ON16 with two PIR's, two remotes, two master blasters. Owing to our secluded position we need to make life miserable enough for the intruder to leave sooner rather t…

Hi i have a ade ultimate system that is now obsolete with standard id biscuits could anyone please advice which panel is now most engineer and user friendly and would i need to update to id plus biscuits thanks carl

Yesterday, I tried to plug the 8XE internal zone expander on my Premier 24, but it failed: the flash programming connector is longer than the expander support pillars. So it is not possible to clip the pillars. I can make photos if you need to better understand the issue. Please advise. Thanks! (I opened ticket # 24795 for that, but the answer was to ask on the support forum).

Will Eaton I-ON40H panel work with Rapier 6510 sounder? Is there a cloud subscription fee to pay for Eaton I-ON40H e.g. for image verification emails?

i`m looking to install an alarm into my 3 bedroom house. i`m going to fit my self and then get the electrician in to connect the power. i`ve been browsing through and quit like the sound of the veritas 8+. is this a good alarm and easy enough to fit. i have basic knowledge of electrics. any suggestions or comments would be grateful, thanks.

I recently purchased a galaxy flex 20 and 4 DT7450-EOL motion sensors. I wired the sensor according to the instruction manual of the motion sensor. the fault loop to zone 1, Alarm test and tamper to zone 2. The "test" to the +12V since the flex control panel doesn't have a "remote led control". see galaxt installation manual page 17 for the wiring schem in the flex manual. see page 3 for the wiring of the sensor This doesn't seem to work. Can anybody tell if the wiring is correct? I find it odd that no connection is made on the V+ and V- of the sensor.

i`m installing my alarm that i purchased earlier this year. 1. the odyssey 1e, there are three switches inside, is it only the one for the battery to be placed on that i move? 2. i`m wiring to global tamper. can i twist all the power wires together and then insert into power terminals? 3. any zones that i do not use, do i need to use the staple like pieces? any help would be great, thanks...

Am i right in thinking the internal sounder should sound along with the external when the alarm is triggerd? since mine doesnt, all it seems to do is the chime facility. daniel

good morning. can anyone please help me in picking an internal sounder which can work with cpx? thanks

Hi, Just trying to put together a quote for a high end residential property, we are upgrading the video intercom, cctv amd intruder alarm...in the past have used powermax for small residential wireless and galaxy for commercial, client likes fancy toys, is there any intruder and cctv that can be integrated or an intruder system that has an app for a smart phone but the system must be wireless. Basically they want a fleshly system he can show off

Hi, Just trying to put together a quote for a high end residential property, we are upgrading the video intercom, cctv amd intruder alarm...in the past have used powermax for small residential wireless and galaxy for commercial, client likes fancy toys, is there any intruder and cctv that can be integrated or an intruder system that has an app for a smart phone but the system must be wireless. Basically they want a fleshly system he can show off

Hi I'm looking for a wireless intruder alarm for a one floor house. It has to include - 6 wireless PIR detectors - 1 wireless external sounder - GSM/GPRS notification capability. Right now i'm investigating the rokonet wisdom and the visonic powermax. Questions 1- Which one do you think would be the most suitable system? You can refer other systems 2- I didn't find any GSM/GPRS adaptor for the rokonet wisdom in your site. The Wisdom panel refers the capability, is it already included? If not which module should be used? Thanks Nuno

Hi, i need help deciding between a PowerMax + (Visonic) or the Scantronic 9751-EN-00 55K for a 5 bedroom house. I need a 5 PIR, 8-10 shock sensors and 1 door contact with a wired outside bell, with a dial out facility. I also want to be able to hardwire the system to the garage later on. If not is there a better system that you could recommend? Any help would be greatly appreciated Many thanks, Surinder J

I wish to purchase an alarm system. I want high security, minimum false alarms and ease of installation. Ive been looking at Freewave, Risco and Visionic wireless systems. Downsatirs I have 3 living rooms and Kitchen each with a door which opens into a large hall (5 PIR ?). Front and back outer doors (2 Mag) I want telephone notification of myself or neighbour and an exteral and an internal sounder. Please recommend a suitable system Thank You A Adams

Hi Im looking to connect a module to an intruder alarm to send a signal to a panel when the alarm goes off. Is this possible with something like the Flex trigger module?

Hi, Perhaps I could ask your advice as to what alarm system I should install. Firstly I should point out that I am a chartered instrumentation engineer so am used to dealing with complex wired and programmable systems - provided that the appropriate instructions are available to me. I have a three bed property which is in a rural location. The village that I live in has been subject to a recent spate of breakins and alarm systems are springing up all over. My priorities are 1) To discourage a burgalr to even attempting a breakin. 2) Should he attempt a breakin to alarm at the earliest possible opportunity preferably before he has actualy gained access. I …

Please could you give me some advice on a wired alarm system to replace the aging Scantronic 808 system fitted to our house. I am a chartered electrical engineer, used to complex programmable industrial control equipment so will self install. The basic spec is:- 5 off existing PIR

Texecom Connect App – Free to Download The Texecom Connect app is free to install and use. However, to unlock its full functionality, your alarm system must be compatible and properly configured. For remote access and control, a Texecom SmartCom or SmartCom 4G module may be required, depending on your setup. Texecom Connect

Hi, I received delivery of the MCS-710 a week ago. Upon installation the test button sounds the siren after 5 seconds, but it will not enrol with the Visonic Powermax base. There does not appear to be any wireless transmission. Regards

Hello, We recently moved into a house that has a non functional wired ITEC Meridian panel (prob. 20 years old?). It has power to it but the front keypad does not respond to any key presses, and the alarm it not activated by the tamper switches on the panel door. The last occupiers never used it (over 12 years or so) and did not have any codes or manuals so I was thinking that the easiest solution would be to fit a new panel. I've no experience with alarms but I am an electronics engineer so am happy to give it a try with some helpful advice:) Present zone layout: Z1: PIR on stairs (6 core cable) Z2: Garage door magnetic reed switch (6 core cable) Z3: 5 of GS610…